e456a81935
Add two new configurations (qemu-riscv{32,64}_spl_defconfig) with SPL
enabled for RISC-V QEMU. QEMU does not require SPL to run U-Boot. The
configurations are meant to help the development of SPL on RISC-V.
The configurations enable RAM as the only SPL boot device. Images must
be loaded at address 0x80200000. In the default boot flow, U-Boot SPL
starts in machine mode, loads the OpenSBI FW_DYNAMIC firmware and U-Boot
proper from the supplied FIT image, and starts OpenSBI. U-Boot proper is
then started in supervisor mode by OpenSBI.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
108 lines
2.4 KiB
C
108 lines
2.4 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <env.h>
|
|
#include <fdtdec.h>
|
|
#include <spl.h>
|
|
#include <virtio_types.h>
|
|
#include <virtio.h>
|
|
|
|
int board_init(void)
|
|
{
|
|
/*
|
|
* Make sure virtio bus is enumerated so that peripherals
|
|
* on the virtio bus can be discovered by their drivers
|
|
*/
|
|
virtio_init();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
ulong kernel_start;
|
|
ofnode chosen_node;
|
|
int ret;
|
|
|
|
chosen_node = ofnode_path("/chosen");
|
|
if (!ofnode_valid(chosen_node)) {
|
|
debug("No chosen node found, can't get kernel start address\n");
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_ARCH_RV64I
|
|
ret = ofnode_read_u64(chosen_node, "riscv,kernel-start",
|
|
(u64 *)&kernel_start);
|
|
#else
|
|
ret = ofnode_read_u32(chosen_node, "riscv,kernel-start",
|
|
(u32 *)&kernel_start);
|
|
#endif
|
|
if (ret) {
|
|
debug("Can't find kernel start address in device tree\n");
|
|
return 0;
|
|
}
|
|
|
|
env_set_hex("kernel_start", kernel_start);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* QEMU specifies the location of Linux (supplied with the -kernel argument)
|
|
* in the device tree using the riscv,kernel-start and riscv,kernel-end
|
|
* properties. We currently rely on the SBI implementation of BBL to run
|
|
* Linux and therefore embed Linux as payload in BBL. This causes an issue,
|
|
* because BBL detects the kernel properties in the device tree and ignores
|
|
* the Linux payload as a result. To work around this issue, we clear the
|
|
* kernel properties before booting Linux.
|
|
*
|
|
* This workaround can be removed, once we do not require BBL for its SBI
|
|
* implementation anymore.
|
|
*/
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
int chosen_offset, ret;
|
|
|
|
chosen_offset = fdt_path_offset(blob, "/chosen");
|
|
if (chosen_offset < 0)
|
|
return 0;
|
|
|
|
#ifdef CONFIG_ARCH_RV64I
|
|
ret = fdt_setprop_u64(blob, chosen_offset, "riscv,kernel-start", 0);
|
|
#else
|
|
ret = fdt_setprop_u32(blob, chosen_offset, "riscv,kernel-start", 0);
|
|
#endif
|
|
if (ret)
|
|
return ret;
|
|
|
|
#ifdef CONFIG_ARCH_RV64I
|
|
ret = fdt_setprop_u64(blob, chosen_offset, "riscv,kernel-end", 0);
|
|
#else
|
|
ret = fdt_setprop_u32(blob, chosen_offset, "riscv,kernel-end", 0);
|
|
#endif
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_SPL
|
|
u32 spl_boot_device(void)
|
|
{
|
|
/* RISC-V QEMU only supports RAM as SPL boot device */
|
|
return BOOT_DEVICE_RAM;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPL_LOAD_FIT
|
|
int board_fit_config_name_match(const char *name)
|
|
{
|
|
/* boot using first FIT config */
|
|
return 0;
|
|
}
|
|
#endif
|