03544c6640
The driver assumed that I2C1 and I2C2 were always enabled, and if they were not, then an asynchronous abort was (silently) raised, to be caught much later on in the Linux kernel. Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4 are. To make the change binary-invariant, declare I2C1 and I2C2 in every include/configs/ file which defines CONFIG_SYS_I2C_MXC. Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed (CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE) config options. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
82 lines
2.5 KiB
C
82 lines
2.5 KiB
C
/*
|
|
* Copyright (C) 2012 Freescale Semiconductor, Inc.
|
|
*
|
|
* Configuration settings for the Freescale i.MX6Q SabreAuto board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __MX6QSABREAUTO_CONFIG_H
|
|
#define __MX6QSABREAUTO_CONFIG_H
|
|
|
|
#define CONFIG_MACH_TYPE 3529
|
|
#define CONFIG_MXC_UART_BASE UART4_BASE
|
|
#define CONFIG_CONSOLE_DEV "ttymxc3"
|
|
#define CONFIG_MMCROOT "/dev/mmcblk0p2"
|
|
#define PHYS_SDRAM_SIZE (2u * 1024 * 1024 * 1024)
|
|
|
|
/* USB Configs */
|
|
#define CONFIG_CMD_USB
|
|
#define CONFIG_USB_EHCI
|
|
#define CONFIG_USB_EHCI_MX6
|
|
#define CONFIG_USB_STORAGE
|
|
#define CONFIG_USB_HOST_ETHER
|
|
#define CONFIG_USB_ETHER_ASIX
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
|
|
#define CONFIG_PCA953X
|
|
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} }
|
|
|
|
#include "mx6sabre_common.h"
|
|
|
|
#undef CONFIG_SYS_NO_FLASH
|
|
#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
|
|
#define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024)
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
|
|
#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 2
|
|
#if defined(CONFIG_ENV_IS_IN_MMC)
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#endif
|
|
|
|
/* I2C Configs */
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_MXC
|
|
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
/* NAND flash command */
|
|
#define CONFIG_CMD_NAND
|
|
#define CONFIG_CMD_NAND_TRIMFFS
|
|
|
|
/* NAND stuff */
|
|
#define CONFIG_NAND_MXS
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE 0x40000000
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
|
|
/* DMA stuff, needed for GPMI/MXS NAND support */
|
|
#define CONFIG_APBH_DMA
|
|
#define CONFIG_APBH_DMA_BURST
|
|
#define CONFIG_APBH_DMA_BURST8
|
|
|
|
/* PMIC */
|
|
#define CONFIG_POWER
|
|
#define CONFIG_POWER_I2C
|
|
#define CONFIG_POWER_PFUZE100
|
|
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
|
|
|
|
#endif /* __MX6QSABREAUTO_CONFIG_H */
|