u-boot/configs/ls1028ardb_tfa_SECURE_BOOT_defconfig
Kuldeep Singh 36df9c7e66 configs: ls1028a: Enable FSPI support
Enable FSPI controller support. So, flash environment can now be used

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04 16:19:37 +05:30

80 lines
1.8 KiB
Plaintext

CONFIG_ARM=y
CONFIG_TARGET_LS1028ARDB=y
CONFIG_TFABOOT=y
CONFIG_SYS_MALLOC_F_LEN=0x6000
CONFIG_NXP_ESBC=y
CONFIG_ENV_SIZE=0x2000
CONFIG_DM_GPIO=y
CONFIG_FSPI_AHB_EN_4BYTE=y
CONFIG_NR_DRAM_BANKS=2
CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_BOOTDELAY=10
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256 video=1920x1080-32@60 cma=256M"
CONFIG_CMD_GREPENV=y
CONFIG_CMD_DM=y
CONFIG_CMD_GPT=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PCI=y
CONFIG_CMD_USB=y
CONFIG_CMD_WDT=y
CONFIG_CMD_CACHE=y
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-rdb"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_SCSI_AHCI=y
CONFIG_SATA_CEVA=y
CONFIG_DM_I2C=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_I2C_DEFAULT_BUS_NUMBER=0
CONFIG_I2C_MUX=y
CONFIG_I2C_MUX_PCA954x=y
CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_MTD=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_PHYLIB=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_VITESSE=y
CONFIG_DM_ETH=y
CONFIG_DM_MDIO=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
CONFIG_FSL_ENETC=y
CONFIG_PCI=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_ECAM_GENERIC=y
CONFIG_PCIE_LAYERSCAPE=y
CONFIG_DM_RTC=y
CONFIG_RTC_PCF2127=y
CONFIG_SCSI=y
CONFIG_DM_SCSI=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
CONFIG_NXP_FSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
CONFIG_WDT=y
CONFIG_WDT_SP805=y
CONFIG_RSA=y
CONFIG_CMD_SETEXPR=y
CONFIG_OF_LIBFDT_OVERLAY=y
CONFIG_EFI_LOADER_BOUNCE_BUFFER=y