a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
85 lines
2.2 KiB
Plaintext
85 lines
2.2 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_K3=y
|
|
CONFIG_TI_SECURE_DEVICE=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x8000
|
|
CONFIG_SOC_K3_AM6=y
|
|
CONFIG_TARGET_AM654_A53_EVM=y
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
|
CONFIG_ENV_SIZE=0x20000
|
|
CONFIG_SPL_STACK_R_ADDR=0x82000000
|
|
CONFIG_NR_DRAM_BANKS=2
|
|
CONFIG_SPL_FS_FAT=y
|
|
CONFIG_SPL_LIBDISK_SUPPORT=y
|
|
CONFIG_SPL_TEXT_BASE=0x80080000
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
|
|
CONFIG_FIT_IMAGE_POST_PROCESS=y
|
|
CONFIG_SPL_LOAD_FIT=y
|
|
CONFIG_SPL_FIT_IMAGE_POST_PROCESS=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run get_fit_${boot}; run get_overlaystring; run run_fit"
|
|
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
|
|
CONFIG_SPL_STACK_R=y
|
|
CONFIG_SPL_SEPARATE_BSS=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
|
|
CONFIG_SPL_I2C_SUPPORT=y
|
|
CONFIG_SPL_DM_MAILBOX=y
|
|
CONFIG_SPL_DM_RESET=y
|
|
CONFIG_SPL_POWER_DOMAIN=y
|
|
CONFIG_SPL_YMODEM_SUPPORT=y
|
|
CONFIG_CMD_ASKENV=y
|
|
# CONFIG_CMD_FLASH is not set
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_TIME=y
|
|
# CONFIG_ISO_PARTITION is not set
|
|
# CONFIG_EFI_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="k3-am654-base-board"
|
|
CONFIG_SPL_MULTI_DTB_FIT=y
|
|
CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
|
|
CONFIG_ENV_IS_IN_FAT=y
|
|
CONFIG_ENV_FAT_INTERFACE="mmc"
|
|
CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_SPL_DM_SEQ_ALIAS=y
|
|
CONFIG_CLK=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_CLK_TI_SCI=y
|
|
CONFIG_DMA_CHANNELS=y
|
|
CONFIG_TI_K3_NAVSS_UDMA=y
|
|
CONFIG_TI_SCI_PROTOCOL=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DM_PCA953X=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_SYS_I2C_OMAP24XX=y
|
|
CONFIG_DM_MAILBOX=y
|
|
CONFIG_K3_SEC_PROXY=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_MMC_SDHCI=y
|
|
CONFIG_PINCTRL=y
|
|
# CONFIG_PINCTRL_GENERIC is not set
|
|
CONFIG_SPL_PINCTRL=y
|
|
# CONFIG_SPL_PINCTRL_GENERIC is not set
|
|
CONFIG_PINCTRL_SINGLE=y
|
|
CONFIG_POWER_DOMAIN=y
|
|
CONFIG_TI_SCI_POWER_DOMAIN=y
|
|
CONFIG_DM_RESET=y
|
|
CONFIG_RESET_TI_SCI=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_SOC_TI=y
|
|
CONFIG_SYSRESET=y
|
|
CONFIG_SPL_SYSRESET=y
|
|
CONFIG_SYSRESET_TI_SCI=y
|
|
CONFIG_OF_LIBFDT_OVERLAY=y
|