0e14cdfaf3
This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini <trini@konsulko.com>
112 lines
3.0 KiB
Plaintext
112 lines
3.0 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_TARGET_LS1046ARDB=y
|
|
CONFIG_SYS_TEXT_BASE=0x82000000
|
|
CONFIG_SYS_MALLOC_LEN=0x102000
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=2
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x300000
|
|
CONFIG_ENV_SECT_SIZE=0x40000
|
|
CONFIG_SYS_I2C_MXC_I2C1=y
|
|
CONFIG_SYS_I2C_MXC_I2C2=y
|
|
CONFIG_SYS_I2C_MXC_I2C3=y
|
|
CONFIG_SYS_I2C_MXC_I2C4=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
|
|
CONFIG_SPL_TEXT_BASE=0x10000000
|
|
CONFIG_FSL_LS_PPA=y
|
|
CONFIG_SPL_FSL_LS_PPA=y
|
|
CONFIG_QSPI_AHB_INIT=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL_DRIVERS_MISC=y
|
|
CONFIG_SPL=y
|
|
CONFIG_AHCI=y
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_REMAKE_ELF=y
|
|
CONFIG_MP=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_SPL_LOAD_FIT=y
|
|
# CONFIG_USE_SPL_FIT_GENERATOR is not set
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_RAMBOOT_PBL=y
|
|
CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1046ardb/ls1046ardb_qspi_pbi.cfg"
|
|
CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1046ardb/ls1046ardb_rcw_qspi.cfg"
|
|
CONFIG_QSPI_BOOT=y
|
|
CONFIG_BOOTDELAY=10
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=1550000.spi-0:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)"
|
|
CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;;"
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_SPL_BOARD_INIT=y
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_MPC8XXX_INIT_DDR=y
|
|
CONFIG_SPL_NOR_SUPPORT=y
|
|
CONFIG_SPL_OS_BOOT=y
|
|
CONFIG_SYS_OS_BASE=0x40980000
|
|
CONFIG_SPL_WATCHDOG=y
|
|
CONFIG_CMD_SPL=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
|
|
CONFIG_CMD_DM=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.spi-0:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)"
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_SPL_ENV_IS_NOWHERE=y
|
|
CONFIG_USE_ETHPRIME=y
|
|
CONFIG_ETHPRIME="FM1@DTSEC3"
|
|
CONFIG_DM=y
|
|
CONFIG_SATA=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_FSL_CAAM=y
|
|
CONFIG_DDR_ECC=y
|
|
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
|
|
CONFIG_MPC8XXX_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x53
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_FSL_IFC=y
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
# CONFIG_SPI_FLASH_BAR is not set
|
|
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_REALTEK=y
|
|
CONFIG_PHY_FIXED=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_DM_MDIO=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_E1000=y
|
|
CONFIG_FMAN_ENET=y
|
|
CONFIG_SYS_FMAN_FW_ADDR=0x40900000
|
|
CONFIG_NVME_PCI=y
|
|
CONFIG_PCI=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_PCIE_LAYERSCAPE_EP=y
|
|
CONFIG_POWER_LEGACY=y
|
|
CONFIG_POWER_I2C=y
|
|
CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|
|
CONFIG_SPL_GZIP=y
|
|
CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
|