a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
129 lines
3.5 KiB
C
129 lines
3.5 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2010
|
|
* Ilko Iliev <iliev@ronetix.at>
|
|
* Asen Dimov <dimov@ronetix.at>
|
|
* Ronetix GmbH <www.ronetix.at>
|
|
*
|
|
* (C) Copyright 2007-2008
|
|
* Stelian Pop <stelian@popies.net>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
*
|
|
* Configuation settings for the PM9G45 board.
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/* ARM asynchronous clock */
|
|
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
|
|
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
|
|
|
|
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
#define CONFIG_SKIP_LOWLEVEL_INIT
|
|
|
|
/* general purpose I/O */
|
|
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/* SDRAM */
|
|
#define CONFIG_SYS_SDRAM_BASE 0x70000000
|
|
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
|
|
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
|
|
|
|
/* NAND flash */
|
|
#ifdef CONFIG_CMD_NAND
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
|
|
#define CONFIG_SYS_NAND_DBW_8
|
|
/* our ALE is AD21 */
|
|
#define CONFIG_SYS_NAND_MASK_ALE BIT(21)
|
|
/* our CLE is AD22 */
|
|
#define CONFIG_SYS_NAND_MASK_CLE BIT(22)
|
|
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
|
|
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD3
|
|
#define CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
|
|
#endif
|
|
|
|
/* Ethernet */
|
|
#define CONFIG_RESET_PHY_R
|
|
#define CONFIG_AT91_WANTS_COMMON_PHY
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
|
|
#define CONFIG_SYS_MEMTEST_END 0x23e00000
|
|
|
|
#ifdef CONFIG_NAND_BOOT
|
|
/* bootstrap + u-boot + env in nandflash */
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"nand read 0x70000000 0x200000 0x300000;" \
|
|
"bootm 0x70000000"
|
|
#elif CONFIG_SD_BOOT
|
|
/* bootstrap + u-boot + env + linux in mmc */
|
|
|
|
#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x71000000 dtb; " \
|
|
"fatload mmc 0:1 0x72000000 zImage; " \
|
|
"bootz 0x72000000 - 0x71000000"
|
|
#endif
|
|
|
|
/*
|
|
* Size of malloc() pool
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \
|
|
128 * 1024, 0x1000)
|
|
|
|
/* Defines for SPL */
|
|
#define CONFIG_SPL_MAX_SIZE 0x010000
|
|
#define CONFIG_SPL_STACK 0x310000
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN 0x80000
|
|
|
|
#ifdef CONFIG_SD_BOOT
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x70000000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x70080000
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
|
|
|
|
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
|
|
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
|
|
#elif CONFIG_NAND_BOOT
|
|
#define CONFIG_SPL_NAND_DRIVERS
|
|
#define CONFIG_SPL_NAND_BASE
|
|
#define CONFIG_SPL_NAND_ECC
|
|
#define CONFIG_SPL_NAND_SOFTECC
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
|
|
#define CONFIG_SYS_NAND_PAGE_COUNT 64
|
|
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
|
|
#define CONFIG_SYS_NAND_ECCSIZE 256
|
|
#define CONFIG_SYS_NAND_ECCBYTES 3
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
|
|
48, 49, 50, 51, 52, 53, 54, 55, \
|
|
56, 57, 58, 59, 60, 61, 62, 63, }
|
|
#endif
|
|
|
|
#define CONFIG_SPL_ATMEL_SIZE
|
|
#define CONFIG_SYS_MASTER_CLOCK 132096000
|
|
#define CONFIG_SYS_AT91_PLLA 0x20c73f03
|
|
#define CONFIG_SYS_MCKR 0x1301
|
|
#define CONFIG_SYS_MCKR_CSS 0x1302
|
|
|
|
#endif
|