320d266368
Add the needed information to enable the debug uart to have printf before the serial driver probe (so before probe for clock, pincontrol and reset drivers) To enable the debug on uart 4 (default console): + CONFIG_DEBUG_UART=y + CONFIG_DEBUG_UART_STM32=y Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
73 lines
1.5 KiB
Plaintext
73 lines
1.5 KiB
Plaintext
if ARCH_STM32MP
|
|
|
|
config SPL
|
|
select SPL_BOARD_INIT
|
|
select SPL_CLK
|
|
select SPL_DM
|
|
select SPL_DM_SEQ_ALIAS
|
|
select SPL_FRAMEWORK
|
|
select SPL_GPIO_SUPPORT
|
|
select SPL_LIBCOMMON_SUPPORT
|
|
select SPL_LIBGENERIC_SUPPORT
|
|
select SPL_OF_CONTROL
|
|
select SPL_OF_TRANSLATE
|
|
select SPL_PINCTRL
|
|
select SPL_REGMAP
|
|
select SPL_RESET_SUPPORT
|
|
select SPL_SERIAL_SUPPORT
|
|
select SPL_SYSCON
|
|
select SPL_DRIVERS_MISC_SUPPORT
|
|
imply SPL_LIBDISK_SUPPORT
|
|
|
|
config SYS_SOC
|
|
default "stm32mp"
|
|
|
|
config TARGET_STM32MP1
|
|
bool "Support stm32mp1xx"
|
|
select ARCH_SUPPORT_PSCI
|
|
select CPU_V7A
|
|
select CPU_V7_HAS_NONSEC
|
|
select CPU_V7_HAS_VIRT
|
|
select PINCTRL_STM32
|
|
select STM32_RESET
|
|
select SYS_ARCH_TIMER
|
|
select SYSRESET_SYSCON
|
|
help
|
|
target STMicroelectronics SOC STM32MP1 family
|
|
STMicroelectronics MPU with core ARMv7
|
|
|
|
config SYS_TEXT_BASE
|
|
prompt "U-Boot base address"
|
|
default 0xC0100000
|
|
help
|
|
configure the U-Boot base address
|
|
when DDR driver is used:
|
|
DDR + 1MB (0xC0100000)
|
|
|
|
config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2
|
|
hex "Partition on MMC2 to use to load U-Boot from"
|
|
depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
|
|
default 1
|
|
help
|
|
Partition on the second MMC to load U-Boot from when the MMC is being
|
|
used in raw mode
|
|
|
|
source "board/st/stm32mp1/Kconfig"
|
|
|
|
# currently activated for debug / should be deactivated for real product
|
|
if DEBUG_UART
|
|
|
|
config DEBUG_UART_BOARD_INIT
|
|
default y
|
|
|
|
# debug on UART4 by default
|
|
config DEBUG_UART_BASE
|
|
default 0x40010000
|
|
|
|
# clock source is HSI on reset
|
|
config DEBUG_UART_CLOCK
|
|
default 64000000
|
|
endif
|
|
|
|
endif
|