2548493ab4
When you enable CONFIG_OF_LIVE, you will end up with a lot of conversions. To generate this commit, I used coccinelle excluding drivers/core/, include/dm/, and test/ The semantic patch that makes this change is as follows: <smpl> @@ expression dev; @@ -devfdt_get_addr(dev) +dev_read_addr(dev) </smpl> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
1832 lines
51 KiB
C
1832 lines
51 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Driver for Marvell NETA network card for Armada XP and Armada 370 SoCs.
|
|
*
|
|
* U-Boot version:
|
|
* Copyright (C) 2014-2015 Stefan Roese <sr@denx.de>
|
|
*
|
|
* Based on the Linux version which is:
|
|
* Copyright (C) 2012 Marvell
|
|
*
|
|
* Rami Rosen <rosenr@marvell.com>
|
|
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <cpu_func.h>
|
|
#include <dm.h>
|
|
#include <log.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <config.h>
|
|
#include <malloc.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/io.h>
|
|
#include <dm/device_compat.h>
|
|
#include <dm/devres.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/bug.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/errno.h>
|
|
#include <phy.h>
|
|
#include <miiphy.h>
|
|
#include <watchdog.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <linux/compat.h>
|
|
#include <linux/mbus.h>
|
|
#include <asm-generic/gpio.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#if !defined(CONFIG_PHYLIB)
|
|
# error Marvell mvneta requires PHYLIB
|
|
#endif
|
|
|
|
#define CONFIG_NR_CPUS 1
|
|
#define ETH_HLEN 14 /* Total octets in header */
|
|
|
|
/* 2(HW hdr) 14(MAC hdr) 4(CRC) 32(extra for cache prefetch) */
|
|
#define WRAP (2 + ETH_HLEN + 4 + 32)
|
|
#define MTU 1500
|
|
#define RX_BUFFER_SIZE (ALIGN(MTU + WRAP, ARCH_DMA_MINALIGN))
|
|
|
|
#define MVNETA_SMI_TIMEOUT 10000
|
|
|
|
/* Registers */
|
|
#define MVNETA_RXQ_CONFIG_REG(q) (0x1400 + ((q) << 2))
|
|
#define MVNETA_RXQ_HW_BUF_ALLOC BIT(1)
|
|
#define MVNETA_RXQ_PKT_OFFSET_ALL_MASK (0xf << 8)
|
|
#define MVNETA_RXQ_PKT_OFFSET_MASK(offs) ((offs) << 8)
|
|
#define MVNETA_RXQ_THRESHOLD_REG(q) (0x14c0 + ((q) << 2))
|
|
#define MVNETA_RXQ_NON_OCCUPIED(v) ((v) << 16)
|
|
#define MVNETA_RXQ_BASE_ADDR_REG(q) (0x1480 + ((q) << 2))
|
|
#define MVNETA_RXQ_SIZE_REG(q) (0x14a0 + ((q) << 2))
|
|
#define MVNETA_RXQ_BUF_SIZE_SHIFT 19
|
|
#define MVNETA_RXQ_BUF_SIZE_MASK (0x1fff << 19)
|
|
#define MVNETA_RXQ_STATUS_REG(q) (0x14e0 + ((q) << 2))
|
|
#define MVNETA_RXQ_OCCUPIED_ALL_MASK 0x3fff
|
|
#define MVNETA_RXQ_STATUS_UPDATE_REG(q) (0x1500 + ((q) << 2))
|
|
#define MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT 16
|
|
#define MVNETA_RXQ_ADD_NON_OCCUPIED_MAX 255
|
|
#define MVNETA_PORT_RX_RESET 0x1cc0
|
|
#define MVNETA_PORT_RX_DMA_RESET BIT(0)
|
|
#define MVNETA_PHY_ADDR 0x2000
|
|
#define MVNETA_PHY_ADDR_MASK 0x1f
|
|
#define MVNETA_SMI 0x2004
|
|
#define MVNETA_PHY_REG_MASK 0x1f
|
|
/* SMI register fields */
|
|
#define MVNETA_SMI_DATA_OFFS 0 /* Data */
|
|
#define MVNETA_SMI_DATA_MASK (0xffff << MVNETA_SMI_DATA_OFFS)
|
|
#define MVNETA_SMI_DEV_ADDR_OFFS 16 /* PHY device address */
|
|
#define MVNETA_SMI_REG_ADDR_OFFS 21 /* PHY device reg addr*/
|
|
#define MVNETA_SMI_OPCODE_OFFS 26 /* Write/Read opcode */
|
|
#define MVNETA_SMI_OPCODE_READ (1 << MVNETA_SMI_OPCODE_OFFS)
|
|
#define MVNETA_SMI_READ_VALID (1 << 27) /* Read Valid */
|
|
#define MVNETA_SMI_BUSY (1 << 28) /* Busy */
|
|
#define MVNETA_MBUS_RETRY 0x2010
|
|
#define MVNETA_UNIT_INTR_CAUSE 0x2080
|
|
#define MVNETA_UNIT_CONTROL 0x20B0
|
|
#define MVNETA_PHY_POLLING_ENABLE BIT(1)
|
|
#define MVNETA_WIN_BASE(w) (0x2200 + ((w) << 3))
|
|
#define MVNETA_WIN_SIZE(w) (0x2204 + ((w) << 3))
|
|
#define MVNETA_WIN_REMAP(w) (0x2280 + ((w) << 2))
|
|
#define MVNETA_WIN_SIZE_MASK (0xffff0000)
|
|
#define MVNETA_BASE_ADDR_ENABLE 0x2290
|
|
#define MVNETA_BASE_ADDR_ENABLE_BIT 0x1
|
|
#define MVNETA_PORT_ACCESS_PROTECT 0x2294
|
|
#define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3
|
|
#define MVNETA_PORT_CONFIG 0x2400
|
|
#define MVNETA_UNI_PROMISC_MODE BIT(0)
|
|
#define MVNETA_DEF_RXQ(q) ((q) << 1)
|
|
#define MVNETA_DEF_RXQ_ARP(q) ((q) << 4)
|
|
#define MVNETA_TX_UNSET_ERR_SUM BIT(12)
|
|
#define MVNETA_DEF_RXQ_TCP(q) ((q) << 16)
|
|
#define MVNETA_DEF_RXQ_UDP(q) ((q) << 19)
|
|
#define MVNETA_DEF_RXQ_BPDU(q) ((q) << 22)
|
|
#define MVNETA_RX_CSUM_WITH_PSEUDO_HDR BIT(25)
|
|
#define MVNETA_PORT_CONFIG_DEFL_VALUE(q) (MVNETA_DEF_RXQ(q) | \
|
|
MVNETA_DEF_RXQ_ARP(q) | \
|
|
MVNETA_DEF_RXQ_TCP(q) | \
|
|
MVNETA_DEF_RXQ_UDP(q) | \
|
|
MVNETA_DEF_RXQ_BPDU(q) | \
|
|
MVNETA_TX_UNSET_ERR_SUM | \
|
|
MVNETA_RX_CSUM_WITH_PSEUDO_HDR)
|
|
#define MVNETA_PORT_CONFIG_EXTEND 0x2404
|
|
#define MVNETA_MAC_ADDR_LOW 0x2414
|
|
#define MVNETA_MAC_ADDR_HIGH 0x2418
|
|
#define MVNETA_SDMA_CONFIG 0x241c
|
|
#define MVNETA_SDMA_BRST_SIZE_16 4
|
|
#define MVNETA_RX_BRST_SZ_MASK(burst) ((burst) << 1)
|
|
#define MVNETA_RX_NO_DATA_SWAP BIT(4)
|
|
#define MVNETA_TX_NO_DATA_SWAP BIT(5)
|
|
#define MVNETA_DESC_SWAP BIT(6)
|
|
#define MVNETA_TX_BRST_SZ_MASK(burst) ((burst) << 22)
|
|
#define MVNETA_PORT_STATUS 0x2444
|
|
#define MVNETA_TX_IN_PRGRS BIT(1)
|
|
#define MVNETA_TX_FIFO_EMPTY BIT(8)
|
|
#define MVNETA_RX_MIN_FRAME_SIZE 0x247c
|
|
#define MVNETA_SERDES_CFG 0x24A0
|
|
#define MVNETA_SGMII_SERDES_PROTO 0x0cc7
|
|
#define MVNETA_QSGMII_SERDES_PROTO 0x0667
|
|
#define MVNETA_TYPE_PRIO 0x24bc
|
|
#define MVNETA_FORCE_UNI BIT(21)
|
|
#define MVNETA_TXQ_CMD_1 0x24e4
|
|
#define MVNETA_TXQ_CMD 0x2448
|
|
#define MVNETA_TXQ_DISABLE_SHIFT 8
|
|
#define MVNETA_TXQ_ENABLE_MASK 0x000000ff
|
|
#define MVNETA_ACC_MODE 0x2500
|
|
#define MVNETA_CPU_MAP(cpu) (0x2540 + ((cpu) << 2))
|
|
#define MVNETA_CPU_RXQ_ACCESS_ALL_MASK 0x000000ff
|
|
#define MVNETA_CPU_TXQ_ACCESS_ALL_MASK 0x0000ff00
|
|
#define MVNETA_RXQ_TIME_COAL_REG(q) (0x2580 + ((q) << 2))
|
|
|
|
/* Exception Interrupt Port/Queue Cause register */
|
|
|
|
#define MVNETA_INTR_NEW_CAUSE 0x25a0
|
|
#define MVNETA_INTR_NEW_MASK 0x25a4
|
|
|
|
/* bits 0..7 = TXQ SENT, one bit per queue.
|
|
* bits 8..15 = RXQ OCCUP, one bit per queue.
|
|
* bits 16..23 = RXQ FREE, one bit per queue.
|
|
* bit 29 = OLD_REG_SUM, see old reg ?
|
|
* bit 30 = TX_ERR_SUM, one bit for 4 ports
|
|
* bit 31 = MISC_SUM, one bit for 4 ports
|
|
*/
|
|
#define MVNETA_TX_INTR_MASK(nr_txqs) (((1 << nr_txqs) - 1) << 0)
|
|
#define MVNETA_TX_INTR_MASK_ALL (0xff << 0)
|
|
#define MVNETA_RX_INTR_MASK(nr_rxqs) (((1 << nr_rxqs) - 1) << 8)
|
|
#define MVNETA_RX_INTR_MASK_ALL (0xff << 8)
|
|
|
|
#define MVNETA_INTR_OLD_CAUSE 0x25a8
|
|
#define MVNETA_INTR_OLD_MASK 0x25ac
|
|
|
|
/* Data Path Port/Queue Cause Register */
|
|
#define MVNETA_INTR_MISC_CAUSE 0x25b0
|
|
#define MVNETA_INTR_MISC_MASK 0x25b4
|
|
#define MVNETA_INTR_ENABLE 0x25b8
|
|
|
|
#define MVNETA_RXQ_CMD 0x2680
|
|
#define MVNETA_RXQ_DISABLE_SHIFT 8
|
|
#define MVNETA_RXQ_ENABLE_MASK 0x000000ff
|
|
#define MVETH_TXQ_TOKEN_COUNT_REG(q) (0x2700 + ((q) << 4))
|
|
#define MVETH_TXQ_TOKEN_CFG_REG(q) (0x2704 + ((q) << 4))
|
|
#define MVNETA_GMAC_CTRL_0 0x2c00
|
|
#define MVNETA_GMAC_MAX_RX_SIZE_SHIFT 2
|
|
#define MVNETA_GMAC_MAX_RX_SIZE_MASK 0x7ffc
|
|
#define MVNETA_GMAC0_PORT_ENABLE BIT(0)
|
|
#define MVNETA_GMAC_CTRL_2 0x2c08
|
|
#define MVNETA_GMAC2_PCS_ENABLE BIT(3)
|
|
#define MVNETA_GMAC2_PORT_RGMII BIT(4)
|
|
#define MVNETA_GMAC2_PORT_RESET BIT(6)
|
|
#define MVNETA_GMAC_STATUS 0x2c10
|
|
#define MVNETA_GMAC_LINK_UP BIT(0)
|
|
#define MVNETA_GMAC_SPEED_1000 BIT(1)
|
|
#define MVNETA_GMAC_SPEED_100 BIT(2)
|
|
#define MVNETA_GMAC_FULL_DUPLEX BIT(3)
|
|
#define MVNETA_GMAC_RX_FLOW_CTRL_ENABLE BIT(4)
|
|
#define MVNETA_GMAC_TX_FLOW_CTRL_ENABLE BIT(5)
|
|
#define MVNETA_GMAC_RX_FLOW_CTRL_ACTIVE BIT(6)
|
|
#define MVNETA_GMAC_TX_FLOW_CTRL_ACTIVE BIT(7)
|
|
#define MVNETA_GMAC_AUTONEG_CONFIG 0x2c0c
|
|
#define MVNETA_GMAC_FORCE_LINK_DOWN BIT(0)
|
|
#define MVNETA_GMAC_FORCE_LINK_PASS BIT(1)
|
|
#define MVNETA_GMAC_FORCE_LINK_UP (BIT(0) | BIT(1))
|
|
#define MVNETA_GMAC_IB_BYPASS_AN_EN BIT(3)
|
|
#define MVNETA_GMAC_CONFIG_MII_SPEED BIT(5)
|
|
#define MVNETA_GMAC_CONFIG_GMII_SPEED BIT(6)
|
|
#define MVNETA_GMAC_AN_SPEED_EN BIT(7)
|
|
#define MVNETA_GMAC_SET_FC_EN BIT(8)
|
|
#define MVNETA_GMAC_ADVERT_FC_EN BIT(9)
|
|
#define MVNETA_GMAC_CONFIG_FULL_DUPLEX BIT(12)
|
|
#define MVNETA_GMAC_AN_DUPLEX_EN BIT(13)
|
|
#define MVNETA_GMAC_SAMPLE_TX_CFG_EN BIT(15)
|
|
#define MVNETA_MIB_COUNTERS_BASE 0x3080
|
|
#define MVNETA_MIB_LATE_COLLISION 0x7c
|
|
#define MVNETA_DA_FILT_SPEC_MCAST 0x3400
|
|
#define MVNETA_DA_FILT_OTH_MCAST 0x3500
|
|
#define MVNETA_DA_FILT_UCAST_BASE 0x3600
|
|
#define MVNETA_TXQ_BASE_ADDR_REG(q) (0x3c00 + ((q) << 2))
|
|
#define MVNETA_TXQ_SIZE_REG(q) (0x3c20 + ((q) << 2))
|
|
#define MVNETA_TXQ_SENT_THRESH_ALL_MASK 0x3fff0000
|
|
#define MVNETA_TXQ_SENT_THRESH_MASK(coal) ((coal) << 16)
|
|
#define MVNETA_TXQ_UPDATE_REG(q) (0x3c60 + ((q) << 2))
|
|
#define MVNETA_TXQ_DEC_SENT_SHIFT 16
|
|
#define MVNETA_TXQ_STATUS_REG(q) (0x3c40 + ((q) << 2))
|
|
#define MVNETA_TXQ_SENT_DESC_SHIFT 16
|
|
#define MVNETA_TXQ_SENT_DESC_MASK 0x3fff0000
|
|
#define MVNETA_PORT_TX_RESET 0x3cf0
|
|
#define MVNETA_PORT_TX_DMA_RESET BIT(0)
|
|
#define MVNETA_TX_MTU 0x3e0c
|
|
#define MVNETA_TX_TOKEN_SIZE 0x3e14
|
|
#define MVNETA_TX_TOKEN_SIZE_MAX 0xffffffff
|
|
#define MVNETA_TXQ_TOKEN_SIZE_REG(q) (0x3e40 + ((q) << 2))
|
|
#define MVNETA_TXQ_TOKEN_SIZE_MAX 0x7fffffff
|
|
|
|
/* Descriptor ring Macros */
|
|
#define MVNETA_QUEUE_NEXT_DESC(q, index) \
|
|
(((index) < (q)->last_desc) ? ((index) + 1) : 0)
|
|
|
|
/* Various constants */
|
|
|
|
/* Coalescing */
|
|
#define MVNETA_TXDONE_COAL_PKTS 16
|
|
#define MVNETA_RX_COAL_PKTS 32
|
|
#define MVNETA_RX_COAL_USEC 100
|
|
|
|
/* The two bytes Marvell header. Either contains a special value used
|
|
* by Marvell switches when a specific hardware mode is enabled (not
|
|
* supported by this driver) or is filled automatically by zeroes on
|
|
* the RX side. Those two bytes being at the front of the Ethernet
|
|
* header, they allow to have the IP header aligned on a 4 bytes
|
|
* boundary automatically: the hardware skips those two bytes on its
|
|
* own.
|
|
*/
|
|
#define MVNETA_MH_SIZE 2
|
|
|
|
#define MVNETA_VLAN_TAG_LEN 4
|
|
|
|
#define MVNETA_CPU_D_CACHE_LINE_SIZE 32
|
|
#define MVNETA_TX_CSUM_MAX_SIZE 9800
|
|
#define MVNETA_ACC_MODE_EXT 1
|
|
|
|
/* Timeout constants */
|
|
#define MVNETA_TX_DISABLE_TIMEOUT_MSEC 1000
|
|
#define MVNETA_RX_DISABLE_TIMEOUT_MSEC 1000
|
|
#define MVNETA_TX_FIFO_EMPTY_TIMEOUT 10000
|
|
|
|
#define MVNETA_TX_MTU_MAX 0x3ffff
|
|
|
|
/* Max number of Rx descriptors */
|
|
#define MVNETA_MAX_RXD 16
|
|
|
|
/* Max number of Tx descriptors */
|
|
#define MVNETA_MAX_TXD 16
|
|
|
|
/* descriptor aligned size */
|
|
#define MVNETA_DESC_ALIGNED_SIZE 32
|
|
|
|
struct mvneta_port {
|
|
void __iomem *base;
|
|
struct mvneta_rx_queue *rxqs;
|
|
struct mvneta_tx_queue *txqs;
|
|
|
|
u8 mcast_count[256];
|
|
u16 tx_ring_size;
|
|
u16 rx_ring_size;
|
|
|
|
phy_interface_t phy_interface;
|
|
unsigned int link;
|
|
unsigned int duplex;
|
|
unsigned int speed;
|
|
|
|
int init;
|
|
int phyaddr;
|
|
struct phy_device *phydev;
|
|
#if CONFIG_IS_ENABLED(DM_GPIO)
|
|
struct gpio_desc phy_reset_gpio;
|
|
#endif
|
|
struct mii_dev *bus;
|
|
};
|
|
|
|
/* The mvneta_tx_desc and mvneta_rx_desc structures describe the
|
|
* layout of the transmit and reception DMA descriptors, and their
|
|
* layout is therefore defined by the hardware design
|
|
*/
|
|
|
|
#define MVNETA_TX_L3_OFF_SHIFT 0
|
|
#define MVNETA_TX_IP_HLEN_SHIFT 8
|
|
#define MVNETA_TX_L4_UDP BIT(16)
|
|
#define MVNETA_TX_L3_IP6 BIT(17)
|
|
#define MVNETA_TXD_IP_CSUM BIT(18)
|
|
#define MVNETA_TXD_Z_PAD BIT(19)
|
|
#define MVNETA_TXD_L_DESC BIT(20)
|
|
#define MVNETA_TXD_F_DESC BIT(21)
|
|
#define MVNETA_TXD_FLZ_DESC (MVNETA_TXD_Z_PAD | \
|
|
MVNETA_TXD_L_DESC | \
|
|
MVNETA_TXD_F_DESC)
|
|
#define MVNETA_TX_L4_CSUM_FULL BIT(30)
|
|
#define MVNETA_TX_L4_CSUM_NOT BIT(31)
|
|
|
|
#define MVNETA_RXD_ERR_CRC 0x0
|
|
#define MVNETA_RXD_ERR_SUMMARY BIT(16)
|
|
#define MVNETA_RXD_ERR_OVERRUN BIT(17)
|
|
#define MVNETA_RXD_ERR_LEN BIT(18)
|
|
#define MVNETA_RXD_ERR_RESOURCE (BIT(17) | BIT(18))
|
|
#define MVNETA_RXD_ERR_CODE_MASK (BIT(17) | BIT(18))
|
|
#define MVNETA_RXD_L3_IP4 BIT(25)
|
|
#define MVNETA_RXD_FIRST_LAST_DESC (BIT(26) | BIT(27))
|
|
#define MVNETA_RXD_L4_CSUM_OK BIT(30)
|
|
|
|
struct mvneta_tx_desc {
|
|
u32 command; /* Options used by HW for packet transmitting.*/
|
|
u16 reserverd1; /* csum_l4 (for future use) */
|
|
u16 data_size; /* Data size of transmitted packet in bytes */
|
|
u32 buf_phys_addr; /* Physical addr of transmitted buffer */
|
|
u32 reserved2; /* hw_cmd - (for future use, PMT) */
|
|
u32 reserved3[4]; /* Reserved - (for future use) */
|
|
};
|
|
|
|
struct mvneta_rx_desc {
|
|
u32 status; /* Info about received packet */
|
|
u16 reserved1; /* pnc_info - (for future use, PnC) */
|
|
u16 data_size; /* Size of received packet in bytes */
|
|
|
|
u32 buf_phys_addr; /* Physical address of the buffer */
|
|
u32 reserved2; /* pnc_flow_id (for future use, PnC) */
|
|
|
|
u32 buf_cookie; /* cookie for access to RX buffer in rx path */
|
|
u16 reserved3; /* prefetch_cmd, for future use */
|
|
u16 reserved4; /* csum_l4 - (for future use, PnC) */
|
|
|
|
u32 reserved5; /* pnc_extra PnC (for future use, PnC) */
|
|
u32 reserved6; /* hw_cmd (for future use, PnC and HWF) */
|
|
};
|
|
|
|
struct mvneta_tx_queue {
|
|
/* Number of this TX queue, in the range 0-7 */
|
|
u8 id;
|
|
|
|
/* Number of TX DMA descriptors in the descriptor ring */
|
|
int size;
|
|
|
|
/* Index of last TX DMA descriptor that was inserted */
|
|
int txq_put_index;
|
|
|
|
/* Index of the TX DMA descriptor to be cleaned up */
|
|
int txq_get_index;
|
|
|
|
/* Virtual address of the TX DMA descriptors array */
|
|
struct mvneta_tx_desc *descs;
|
|
|
|
/* DMA address of the TX DMA descriptors array */
|
|
dma_addr_t descs_phys;
|
|
|
|
/* Index of the last TX DMA descriptor */
|
|
int last_desc;
|
|
|
|
/* Index of the next TX DMA descriptor to process */
|
|
int next_desc_to_proc;
|
|
};
|
|
|
|
struct mvneta_rx_queue {
|
|
/* rx queue number, in the range 0-7 */
|
|
u8 id;
|
|
|
|
/* num of rx descriptors in the rx descriptor ring */
|
|
int size;
|
|
|
|
/* Virtual address of the RX DMA descriptors array */
|
|
struct mvneta_rx_desc *descs;
|
|
|
|
/* DMA address of the RX DMA descriptors array */
|
|
dma_addr_t descs_phys;
|
|
|
|
/* Index of the last RX DMA descriptor */
|
|
int last_desc;
|
|
|
|
/* Index of the next RX DMA descriptor to process */
|
|
int next_desc_to_proc;
|
|
};
|
|
|
|
/* U-Boot doesn't use the queues, so set the number to 1 */
|
|
static int rxq_number = 1;
|
|
static int txq_number = 1;
|
|
static int rxq_def;
|
|
|
|
struct buffer_location {
|
|
struct mvneta_tx_desc *tx_descs;
|
|
struct mvneta_rx_desc *rx_descs;
|
|
u32 rx_buffers;
|
|
};
|
|
|
|
/*
|
|
* All 4 interfaces use the same global buffer, since only one interface
|
|
* can be enabled at once
|
|
*/
|
|
static struct buffer_location buffer_loc;
|
|
|
|
/*
|
|
* Page table entries are set to 1MB, or multiples of 1MB
|
|
* (not < 1MB). driver uses less bd's so use 1MB bdspace.
|
|
*/
|
|
#define BD_SPACE (1 << 20)
|
|
|
|
/*
|
|
* Dummy implementation that can be overwritten by a board
|
|
* specific function
|
|
*/
|
|
__weak int board_network_enable(struct mii_dev *bus)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
/* Utility/helper methods */
|
|
|
|
/* Write helper method */
|
|
static void mvreg_write(struct mvneta_port *pp, u32 offset, u32 data)
|
|
{
|
|
writel(data, pp->base + offset);
|
|
}
|
|
|
|
/* Read helper method */
|
|
static u32 mvreg_read(struct mvneta_port *pp, u32 offset)
|
|
{
|
|
return readl(pp->base + offset);
|
|
}
|
|
|
|
/* Clear all MIB counters */
|
|
static void mvneta_mib_counters_clear(struct mvneta_port *pp)
|
|
{
|
|
int i;
|
|
|
|
/* Perform dummy reads from MIB counters */
|
|
for (i = 0; i < MVNETA_MIB_LATE_COLLISION; i += 4)
|
|
mvreg_read(pp, (MVNETA_MIB_COUNTERS_BASE + i));
|
|
}
|
|
|
|
/* Rx descriptors helper methods */
|
|
|
|
/* Checks whether the RX descriptor having this status is both the first
|
|
* and the last descriptor for the RX packet. Each RX packet is currently
|
|
* received through a single RX descriptor, so not having each RX
|
|
* descriptor with its first and last bits set is an error
|
|
*/
|
|
static int mvneta_rxq_desc_is_first_last(u32 status)
|
|
{
|
|
return (status & MVNETA_RXD_FIRST_LAST_DESC) ==
|
|
MVNETA_RXD_FIRST_LAST_DESC;
|
|
}
|
|
|
|
/* Add number of descriptors ready to receive new packets */
|
|
static void mvneta_rxq_non_occup_desc_add(struct mvneta_port *pp,
|
|
struct mvneta_rx_queue *rxq,
|
|
int ndescs)
|
|
{
|
|
/* Only MVNETA_RXQ_ADD_NON_OCCUPIED_MAX (255) descriptors can
|
|
* be added at once
|
|
*/
|
|
while (ndescs > MVNETA_RXQ_ADD_NON_OCCUPIED_MAX) {
|
|
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id),
|
|
(MVNETA_RXQ_ADD_NON_OCCUPIED_MAX <<
|
|
MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT));
|
|
ndescs -= MVNETA_RXQ_ADD_NON_OCCUPIED_MAX;
|
|
}
|
|
|
|
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id),
|
|
(ndescs << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT));
|
|
}
|
|
|
|
/* Get number of RX descriptors occupied by received packets */
|
|
static int mvneta_rxq_busy_desc_num_get(struct mvneta_port *pp,
|
|
struct mvneta_rx_queue *rxq)
|
|
{
|
|
u32 val;
|
|
|
|
val = mvreg_read(pp, MVNETA_RXQ_STATUS_REG(rxq->id));
|
|
return val & MVNETA_RXQ_OCCUPIED_ALL_MASK;
|
|
}
|
|
|
|
/* Update num of rx desc called upon return from rx path or
|
|
* from mvneta_rxq_drop_pkts().
|
|
*/
|
|
static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
|
|
struct mvneta_rx_queue *rxq,
|
|
int rx_done, int rx_filled)
|
|
{
|
|
u32 val;
|
|
|
|
if ((rx_done <= 0xff) && (rx_filled <= 0xff)) {
|
|
val = rx_done |
|
|
(rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT);
|
|
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val);
|
|
return;
|
|
}
|
|
|
|
/* Only 255 descriptors can be added at once */
|
|
while ((rx_done > 0) || (rx_filled > 0)) {
|
|
if (rx_done <= 0xff) {
|
|
val = rx_done;
|
|
rx_done = 0;
|
|
} else {
|
|
val = 0xff;
|
|
rx_done -= 0xff;
|
|
}
|
|
if (rx_filled <= 0xff) {
|
|
val |= rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT;
|
|
rx_filled = 0;
|
|
} else {
|
|
val |= 0xff << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT;
|
|
rx_filled -= 0xff;
|
|
}
|
|
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val);
|
|
}
|
|
}
|
|
|
|
/* Get pointer to next RX descriptor to be processed by SW */
|
|
static struct mvneta_rx_desc *
|
|
mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
|
|
{
|
|
int rx_desc = rxq->next_desc_to_proc;
|
|
|
|
rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
|
|
return rxq->descs + rx_desc;
|
|
}
|
|
|
|
/* Tx descriptors helper methods */
|
|
|
|
/* Update HW with number of TX descriptors to be sent */
|
|
static void mvneta_txq_pend_desc_add(struct mvneta_port *pp,
|
|
struct mvneta_tx_queue *txq,
|
|
int pend_desc)
|
|
{
|
|
u32 val;
|
|
|
|
/* Only 255 descriptors can be added at once ; Assume caller
|
|
* process TX descriptors in quanta less than 256
|
|
*/
|
|
val = pend_desc;
|
|
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
|
|
}
|
|
|
|
/* Get pointer to next TX descriptor to be processed (send) by HW */
|
|
static struct mvneta_tx_desc *
|
|
mvneta_txq_next_desc_get(struct mvneta_tx_queue *txq)
|
|
{
|
|
int tx_desc = txq->next_desc_to_proc;
|
|
|
|
txq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(txq, tx_desc);
|
|
return txq->descs + tx_desc;
|
|
}
|
|
|
|
/* Set rxq buf size */
|
|
static void mvneta_rxq_buf_size_set(struct mvneta_port *pp,
|
|
struct mvneta_rx_queue *rxq,
|
|
int buf_size)
|
|
{
|
|
u32 val;
|
|
|
|
val = mvreg_read(pp, MVNETA_RXQ_SIZE_REG(rxq->id));
|
|
|
|
val &= ~MVNETA_RXQ_BUF_SIZE_MASK;
|
|
val |= ((buf_size >> 3) << MVNETA_RXQ_BUF_SIZE_SHIFT);
|
|
|
|
mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), val);
|
|
}
|
|
|
|
static int mvneta_port_is_fixed_link(struct mvneta_port *pp)
|
|
{
|
|
/* phy_addr is set to invalid value for fixed link */
|
|
return pp->phyaddr > PHY_MAX_ADDR;
|
|
}
|
|
|
|
|
|
/* Start the Ethernet port RX and TX activity */
|
|
static void mvneta_port_up(struct mvneta_port *pp)
|
|
{
|
|
int queue;
|
|
u32 q_map;
|
|
|
|
/* Enable all initialized TXs. */
|
|
mvneta_mib_counters_clear(pp);
|
|
q_map = 0;
|
|
for (queue = 0; queue < txq_number; queue++) {
|
|
struct mvneta_tx_queue *txq = &pp->txqs[queue];
|
|
if (txq->descs != NULL)
|
|
q_map |= (1 << queue);
|
|
}
|
|
mvreg_write(pp, MVNETA_TXQ_CMD, q_map);
|
|
|
|
/* Enable all initialized RXQs. */
|
|
q_map = 0;
|
|
for (queue = 0; queue < rxq_number; queue++) {
|
|
struct mvneta_rx_queue *rxq = &pp->rxqs[queue];
|
|
if (rxq->descs != NULL)
|
|
q_map |= (1 << queue);
|
|
}
|
|
mvreg_write(pp, MVNETA_RXQ_CMD, q_map);
|
|
}
|
|
|
|
/* Stop the Ethernet port activity */
|
|
static void mvneta_port_down(struct mvneta_port *pp)
|
|
{
|
|
u32 val;
|
|
int count;
|
|
|
|
/* Stop Rx port activity. Check port Rx activity. */
|
|
val = mvreg_read(pp, MVNETA_RXQ_CMD) & MVNETA_RXQ_ENABLE_MASK;
|
|
|
|
/* Issue stop command for active channels only */
|
|
if (val != 0)
|
|
mvreg_write(pp, MVNETA_RXQ_CMD,
|
|
val << MVNETA_RXQ_DISABLE_SHIFT);
|
|
|
|
/* Wait for all Rx activity to terminate. */
|
|
count = 0;
|
|
do {
|
|
if (count++ >= MVNETA_RX_DISABLE_TIMEOUT_MSEC) {
|
|
netdev_warn(pp->dev,
|
|
"TIMEOUT for RX stopped ! rx_queue_cmd: 0x08%x\n",
|
|
val);
|
|
break;
|
|
}
|
|
mdelay(1);
|
|
|
|
val = mvreg_read(pp, MVNETA_RXQ_CMD);
|
|
} while (val & 0xff);
|
|
|
|
/* Stop Tx port activity. Check port Tx activity. Issue stop
|
|
* command for active channels only
|
|
*/
|
|
val = (mvreg_read(pp, MVNETA_TXQ_CMD)) & MVNETA_TXQ_ENABLE_MASK;
|
|
|
|
if (val != 0)
|
|
mvreg_write(pp, MVNETA_TXQ_CMD,
|
|
(val << MVNETA_TXQ_DISABLE_SHIFT));
|
|
|
|
/* Wait for all Tx activity to terminate. */
|
|
count = 0;
|
|
do {
|
|
if (count++ >= MVNETA_TX_DISABLE_TIMEOUT_MSEC) {
|
|
netdev_warn(pp->dev,
|
|
"TIMEOUT for TX stopped status=0x%08x\n",
|
|
val);
|
|
break;
|
|
}
|
|
mdelay(1);
|
|
|
|
/* Check TX Command reg that all Txqs are stopped */
|
|
val = mvreg_read(pp, MVNETA_TXQ_CMD);
|
|
|
|
} while (val & 0xff);
|
|
|
|
/* Double check to verify that TX FIFO is empty */
|
|
count = 0;
|
|
do {
|
|
if (count++ >= MVNETA_TX_FIFO_EMPTY_TIMEOUT) {
|
|
netdev_warn(pp->dev,
|
|
"TX FIFO empty timeout status=0x08%x\n",
|
|
val);
|
|
break;
|
|
}
|
|
mdelay(1);
|
|
|
|
val = mvreg_read(pp, MVNETA_PORT_STATUS);
|
|
} while (!(val & MVNETA_TX_FIFO_EMPTY) &&
|
|
(val & MVNETA_TX_IN_PRGRS));
|
|
|
|
udelay(200);
|
|
}
|
|
|
|
/* Enable the port by setting the port enable bit of the MAC control register */
|
|
static void mvneta_port_enable(struct mvneta_port *pp)
|
|
{
|
|
u32 val;
|
|
|
|
/* Enable port */
|
|
val = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
|
|
val |= MVNETA_GMAC0_PORT_ENABLE;
|
|
mvreg_write(pp, MVNETA_GMAC_CTRL_0, val);
|
|
}
|
|
|
|
/* Disable the port and wait for about 200 usec before retuning */
|
|
static void mvneta_port_disable(struct mvneta_port *pp)
|
|
{
|
|
u32 val;
|
|
|
|
/* Reset the Enable bit in the Serial Control Register */
|
|
val = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
|
|
val &= ~MVNETA_GMAC0_PORT_ENABLE;
|
|
mvreg_write(pp, MVNETA_GMAC_CTRL_0, val);
|
|
|
|
udelay(200);
|
|
}
|
|
|
|
/* Multicast tables methods */
|
|
|
|
/* Set all entries in Unicast MAC Table; queue==-1 means reject all */
|
|
static void mvneta_set_ucast_table(struct mvneta_port *pp, int queue)
|
|
{
|
|
int offset;
|
|
u32 val;
|
|
|
|
if (queue == -1) {
|
|
val = 0;
|
|
} else {
|
|
val = 0x1 | (queue << 1);
|
|
val |= (val << 24) | (val << 16) | (val << 8);
|
|
}
|
|
|
|
for (offset = 0; offset <= 0xc; offset += 4)
|
|
mvreg_write(pp, MVNETA_DA_FILT_UCAST_BASE + offset, val);
|
|
}
|
|
|
|
/* Set all entries in Special Multicast MAC Table; queue==-1 means reject all */
|
|
static void mvneta_set_special_mcast_table(struct mvneta_port *pp, int queue)
|
|
{
|
|
int offset;
|
|
u32 val;
|
|
|
|
if (queue == -1) {
|
|
val = 0;
|
|
} else {
|
|
val = 0x1 | (queue << 1);
|
|
val |= (val << 24) | (val << 16) | (val << 8);
|
|
}
|
|
|
|
for (offset = 0; offset <= 0xfc; offset += 4)
|
|
mvreg_write(pp, MVNETA_DA_FILT_SPEC_MCAST + offset, val);
|
|
}
|
|
|
|
/* Set all entries in Other Multicast MAC Table. queue==-1 means reject all */
|
|
static void mvneta_set_other_mcast_table(struct mvneta_port *pp, int queue)
|
|
{
|
|
int offset;
|
|
u32 val;
|
|
|
|
if (queue == -1) {
|
|
memset(pp->mcast_count, 0, sizeof(pp->mcast_count));
|
|
val = 0;
|
|
} else {
|
|
memset(pp->mcast_count, 1, sizeof(pp->mcast_count));
|
|
val = 0x1 | (queue << 1);
|
|
val |= (val << 24) | (val << 16) | (val << 8);
|
|
}
|
|
|
|
for (offset = 0; offset <= 0xfc; offset += 4)
|
|
mvreg_write(pp, MVNETA_DA_FILT_OTH_MCAST + offset, val);
|
|
}
|
|
|
|
/* This method sets defaults to the NETA port:
|
|
* Clears interrupt Cause and Mask registers.
|
|
* Clears all MAC tables.
|
|
* Sets defaults to all registers.
|
|
* Resets RX and TX descriptor rings.
|
|
* Resets PHY.
|
|
* This method can be called after mvneta_port_down() to return the port
|
|
* settings to defaults.
|
|
*/
|
|
static void mvneta_defaults_set(struct mvneta_port *pp)
|
|
{
|
|
int cpu;
|
|
int queue;
|
|
u32 val;
|
|
|
|
/* Clear all Cause registers */
|
|
mvreg_write(pp, MVNETA_INTR_NEW_CAUSE, 0);
|
|
mvreg_write(pp, MVNETA_INTR_OLD_CAUSE, 0);
|
|
mvreg_write(pp, MVNETA_INTR_MISC_CAUSE, 0);
|
|
|
|
/* Mask all interrupts */
|
|
mvreg_write(pp, MVNETA_INTR_NEW_MASK, 0);
|
|
mvreg_write(pp, MVNETA_INTR_OLD_MASK, 0);
|
|
mvreg_write(pp, MVNETA_INTR_MISC_MASK, 0);
|
|
mvreg_write(pp, MVNETA_INTR_ENABLE, 0);
|
|
|
|
/* Enable MBUS Retry bit16 */
|
|
mvreg_write(pp, MVNETA_MBUS_RETRY, 0x20);
|
|
|
|
/* Set CPU queue access map - all CPUs have access to all RX
|
|
* queues and to all TX queues
|
|
*/
|
|
for (cpu = 0; cpu < CONFIG_NR_CPUS; cpu++)
|
|
mvreg_write(pp, MVNETA_CPU_MAP(cpu),
|
|
(MVNETA_CPU_RXQ_ACCESS_ALL_MASK |
|
|
MVNETA_CPU_TXQ_ACCESS_ALL_MASK));
|
|
|
|
/* Reset RX and TX DMAs */
|
|
mvreg_write(pp, MVNETA_PORT_RX_RESET, MVNETA_PORT_RX_DMA_RESET);
|
|
mvreg_write(pp, MVNETA_PORT_TX_RESET, MVNETA_PORT_TX_DMA_RESET);
|
|
|
|
/* Disable Legacy WRR, Disable EJP, Release from reset */
|
|
mvreg_write(pp, MVNETA_TXQ_CMD_1, 0);
|
|
for (queue = 0; queue < txq_number; queue++) {
|
|
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(queue), 0);
|
|
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(queue), 0);
|
|
}
|
|
|
|
mvreg_write(pp, MVNETA_PORT_TX_RESET, 0);
|
|
mvreg_write(pp, MVNETA_PORT_RX_RESET, 0);
|
|
|
|
/* Set Port Acceleration Mode */
|
|
val = MVNETA_ACC_MODE_EXT;
|
|
mvreg_write(pp, MVNETA_ACC_MODE, val);
|
|
|
|
/* Update val of portCfg register accordingly with all RxQueue types */
|
|
val = MVNETA_PORT_CONFIG_DEFL_VALUE(rxq_def);
|
|
mvreg_write(pp, MVNETA_PORT_CONFIG, val);
|
|
|
|
val = 0;
|
|
mvreg_write(pp, MVNETA_PORT_CONFIG_EXTEND, val);
|
|
mvreg_write(pp, MVNETA_RX_MIN_FRAME_SIZE, 64);
|
|
|
|
/* Build PORT_SDMA_CONFIG_REG */
|
|
val = 0;
|
|
|
|
/* Default burst size */
|
|
val |= MVNETA_TX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16);
|
|
val |= MVNETA_RX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16);
|
|
val |= MVNETA_RX_NO_DATA_SWAP | MVNETA_TX_NO_DATA_SWAP;
|
|
|
|
/* Assign port SDMA configuration */
|
|
mvreg_write(pp, MVNETA_SDMA_CONFIG, val);
|
|
|
|
/* Enable PHY polling in hardware if not in fixed-link mode */
|
|
if (!mvneta_port_is_fixed_link(pp)) {
|
|
val = mvreg_read(pp, MVNETA_UNIT_CONTROL);
|
|
val |= MVNETA_PHY_POLLING_ENABLE;
|
|
mvreg_write(pp, MVNETA_UNIT_CONTROL, val);
|
|
}
|
|
|
|
mvneta_set_ucast_table(pp, -1);
|
|
mvneta_set_special_mcast_table(pp, -1);
|
|
mvneta_set_other_mcast_table(pp, -1);
|
|
}
|
|
|
|
/* Set unicast address */
|
|
static void mvneta_set_ucast_addr(struct mvneta_port *pp, u8 last_nibble,
|
|
int queue)
|
|
{
|
|
unsigned int unicast_reg;
|
|
unsigned int tbl_offset;
|
|
unsigned int reg_offset;
|
|
|
|
/* Locate the Unicast table entry */
|
|
last_nibble = (0xf & last_nibble);
|
|
|
|
/* offset from unicast tbl base */
|
|
tbl_offset = (last_nibble / 4) * 4;
|
|
|
|
/* offset within the above reg */
|
|
reg_offset = last_nibble % 4;
|
|
|
|
unicast_reg = mvreg_read(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset));
|
|
|
|
if (queue == -1) {
|
|
/* Clear accepts frame bit at specified unicast DA tbl entry */
|
|
unicast_reg &= ~(0xff << (8 * reg_offset));
|
|
} else {
|
|
unicast_reg &= ~(0xff << (8 * reg_offset));
|
|
unicast_reg |= ((0x01 | (queue << 1)) << (8 * reg_offset));
|
|
}
|
|
|
|
mvreg_write(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset), unicast_reg);
|
|
}
|
|
|
|
/* Set mac address */
|
|
static void mvneta_mac_addr_set(struct mvneta_port *pp, unsigned char *addr,
|
|
int queue)
|
|
{
|
|
unsigned int mac_h;
|
|
unsigned int mac_l;
|
|
|
|
if (queue != -1) {
|
|
mac_l = (addr[4] << 8) | (addr[5]);
|
|
mac_h = (addr[0] << 24) | (addr[1] << 16) |
|
|
(addr[2] << 8) | (addr[3] << 0);
|
|
|
|
mvreg_write(pp, MVNETA_MAC_ADDR_LOW, mac_l);
|
|
mvreg_write(pp, MVNETA_MAC_ADDR_HIGH, mac_h);
|
|
}
|
|
|
|
/* Accept frames of this address */
|
|
mvneta_set_ucast_addr(pp, addr[5], queue);
|
|
}
|
|
|
|
static int mvneta_write_hwaddr(struct udevice *dev)
|
|
{
|
|
mvneta_mac_addr_set(dev_get_priv(dev),
|
|
((struct eth_pdata *)dev_get_platdata(dev))->enetaddr,
|
|
rxq_def);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Handle rx descriptor fill by setting buf_cookie and buf_phys_addr */
|
|
static void mvneta_rx_desc_fill(struct mvneta_rx_desc *rx_desc,
|
|
u32 phys_addr, u32 cookie)
|
|
{
|
|
rx_desc->buf_cookie = cookie;
|
|
rx_desc->buf_phys_addr = phys_addr;
|
|
}
|
|
|
|
/* Decrement sent descriptors counter */
|
|
static void mvneta_txq_sent_desc_dec(struct mvneta_port *pp,
|
|
struct mvneta_tx_queue *txq,
|
|
int sent_desc)
|
|
{
|
|
u32 val;
|
|
|
|
/* Only 255 TX descriptors can be updated at once */
|
|
while (sent_desc > 0xff) {
|
|
val = 0xff << MVNETA_TXQ_DEC_SENT_SHIFT;
|
|
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
|
|
sent_desc = sent_desc - 0xff;
|
|
}
|
|
|
|
val = sent_desc << MVNETA_TXQ_DEC_SENT_SHIFT;
|
|
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
|
|
}
|
|
|
|
/* Get number of TX descriptors already sent by HW */
|
|
static int mvneta_txq_sent_desc_num_get(struct mvneta_port *pp,
|
|
struct mvneta_tx_queue *txq)
|
|
{
|
|
u32 val;
|
|
int sent_desc;
|
|
|
|
val = mvreg_read(pp, MVNETA_TXQ_STATUS_REG(txq->id));
|
|
sent_desc = (val & MVNETA_TXQ_SENT_DESC_MASK) >>
|
|
MVNETA_TXQ_SENT_DESC_SHIFT;
|
|
|
|
return sent_desc;
|
|
}
|
|
|
|
/* Display more error info */
|
|
static void mvneta_rx_error(struct mvneta_port *pp,
|
|
struct mvneta_rx_desc *rx_desc)
|
|
{
|
|
u32 status = rx_desc->status;
|
|
|
|
if (!mvneta_rxq_desc_is_first_last(status)) {
|
|
netdev_err(pp->dev,
|
|
"bad rx status %08x (buffer oversize), size=%d\n",
|
|
status, rx_desc->data_size);
|
|
return;
|
|
}
|
|
|
|
switch (status & MVNETA_RXD_ERR_CODE_MASK) {
|
|
case MVNETA_RXD_ERR_CRC:
|
|
netdev_err(pp->dev, "bad rx status %08x (crc error), size=%d\n",
|
|
status, rx_desc->data_size);
|
|
break;
|
|
case MVNETA_RXD_ERR_OVERRUN:
|
|
netdev_err(pp->dev, "bad rx status %08x (overrun error), size=%d\n",
|
|
status, rx_desc->data_size);
|
|
break;
|
|
case MVNETA_RXD_ERR_LEN:
|
|
netdev_err(pp->dev, "bad rx status %08x (max frame length error), size=%d\n",
|
|
status, rx_desc->data_size);
|
|
break;
|
|
case MVNETA_RXD_ERR_RESOURCE:
|
|
netdev_err(pp->dev, "bad rx status %08x (resource error), size=%d\n",
|
|
status, rx_desc->data_size);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static struct mvneta_rx_queue *mvneta_rxq_handle_get(struct mvneta_port *pp,
|
|
int rxq)
|
|
{
|
|
return &pp->rxqs[rxq];
|
|
}
|
|
|
|
|
|
/* Drop packets received by the RXQ and free buffers */
|
|
static void mvneta_rxq_drop_pkts(struct mvneta_port *pp,
|
|
struct mvneta_rx_queue *rxq)
|
|
{
|
|
int rx_done;
|
|
|
|
rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq);
|
|
if (rx_done)
|
|
mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_done);
|
|
}
|
|
|
|
/* Handle rxq fill: allocates rxq skbs; called when initializing a port */
|
|
static int mvneta_rxq_fill(struct mvneta_port *pp, struct mvneta_rx_queue *rxq,
|
|
int num)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < num; i++) {
|
|
u32 addr;
|
|
|
|
/* U-Boot special: Fill in the rx buffer addresses */
|
|
addr = buffer_loc.rx_buffers + (i * RX_BUFFER_SIZE);
|
|
mvneta_rx_desc_fill(rxq->descs + i, addr, addr);
|
|
}
|
|
|
|
/* Add this number of RX descriptors as non occupied (ready to
|
|
* get packets)
|
|
*/
|
|
mvneta_rxq_non_occup_desc_add(pp, rxq, i);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Rx/Tx queue initialization/cleanup methods */
|
|
|
|
/* Create a specified RX queue */
|
|
static int mvneta_rxq_init(struct mvneta_port *pp,
|
|
struct mvneta_rx_queue *rxq)
|
|
|
|
{
|
|
rxq->size = pp->rx_ring_size;
|
|
|
|
/* Allocate memory for RX descriptors */
|
|
rxq->descs_phys = (dma_addr_t)rxq->descs;
|
|
if (rxq->descs == NULL)
|
|
return -ENOMEM;
|
|
|
|
WARN_ON(rxq->descs != PTR_ALIGN(rxq->descs, ARCH_DMA_MINALIGN));
|
|
|
|
rxq->last_desc = rxq->size - 1;
|
|
|
|
/* Set Rx descriptors queue starting address */
|
|
mvreg_write(pp, MVNETA_RXQ_BASE_ADDR_REG(rxq->id), rxq->descs_phys);
|
|
mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), rxq->size);
|
|
|
|
/* Fill RXQ with buffers from RX pool */
|
|
mvneta_rxq_buf_size_set(pp, rxq, RX_BUFFER_SIZE);
|
|
mvneta_rxq_fill(pp, rxq, rxq->size);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Cleanup Rx queue */
|
|
static void mvneta_rxq_deinit(struct mvneta_port *pp,
|
|
struct mvneta_rx_queue *rxq)
|
|
{
|
|
mvneta_rxq_drop_pkts(pp, rxq);
|
|
|
|
rxq->descs = NULL;
|
|
rxq->last_desc = 0;
|
|
rxq->next_desc_to_proc = 0;
|
|
rxq->descs_phys = 0;
|
|
}
|
|
|
|
/* Create and initialize a tx queue */
|
|
static int mvneta_txq_init(struct mvneta_port *pp,
|
|
struct mvneta_tx_queue *txq)
|
|
{
|
|
txq->size = pp->tx_ring_size;
|
|
|
|
/* Allocate memory for TX descriptors */
|
|
txq->descs_phys = (dma_addr_t)txq->descs;
|
|
if (txq->descs == NULL)
|
|
return -ENOMEM;
|
|
|
|
WARN_ON(txq->descs != PTR_ALIGN(txq->descs, ARCH_DMA_MINALIGN));
|
|
|
|
txq->last_desc = txq->size - 1;
|
|
|
|
/* Set maximum bandwidth for enabled TXQs */
|
|
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0x03ffffff);
|
|
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0x3fffffff);
|
|
|
|
/* Set Tx descriptors queue starting address */
|
|
mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), txq->descs_phys);
|
|
mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), txq->size);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Free allocated resources when mvneta_txq_init() fails to allocate memory*/
|
|
static void mvneta_txq_deinit(struct mvneta_port *pp,
|
|
struct mvneta_tx_queue *txq)
|
|
{
|
|
txq->descs = NULL;
|
|
txq->last_desc = 0;
|
|
txq->next_desc_to_proc = 0;
|
|
txq->descs_phys = 0;
|
|
|
|
/* Set minimum bandwidth for disabled TXQs */
|
|
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0);
|
|
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0);
|
|
|
|
/* Set Tx descriptors queue starting address and size */
|
|
mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), 0);
|
|
mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), 0);
|
|
}
|
|
|
|
/* Cleanup all Tx queues */
|
|
static void mvneta_cleanup_txqs(struct mvneta_port *pp)
|
|
{
|
|
int queue;
|
|
|
|
for (queue = 0; queue < txq_number; queue++)
|
|
mvneta_txq_deinit(pp, &pp->txqs[queue]);
|
|
}
|
|
|
|
/* Cleanup all Rx queues */
|
|
static void mvneta_cleanup_rxqs(struct mvneta_port *pp)
|
|
{
|
|
int queue;
|
|
|
|
for (queue = 0; queue < rxq_number; queue++)
|
|
mvneta_rxq_deinit(pp, &pp->rxqs[queue]);
|
|
}
|
|
|
|
|
|
/* Init all Rx queues */
|
|
static int mvneta_setup_rxqs(struct mvneta_port *pp)
|
|
{
|
|
int queue;
|
|
|
|
for (queue = 0; queue < rxq_number; queue++) {
|
|
int err = mvneta_rxq_init(pp, &pp->rxqs[queue]);
|
|
if (err) {
|
|
netdev_err(pp->dev, "%s: can't create rxq=%d\n",
|
|
__func__, queue);
|
|
mvneta_cleanup_rxqs(pp);
|
|
return err;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Init all tx queues */
|
|
static int mvneta_setup_txqs(struct mvneta_port *pp)
|
|
{
|
|
int queue;
|
|
|
|
for (queue = 0; queue < txq_number; queue++) {
|
|
int err = mvneta_txq_init(pp, &pp->txqs[queue]);
|
|
if (err) {
|
|
netdev_err(pp->dev, "%s: can't create txq=%d\n",
|
|
__func__, queue);
|
|
mvneta_cleanup_txqs(pp);
|
|
return err;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void mvneta_start_dev(struct mvneta_port *pp)
|
|
{
|
|
/* start the Rx/Tx activity */
|
|
mvneta_port_enable(pp);
|
|
}
|
|
|
|
static void mvneta_adjust_link(struct udevice *dev)
|
|
{
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
struct phy_device *phydev = pp->phydev;
|
|
int status_change = 0;
|
|
|
|
if (mvneta_port_is_fixed_link(pp)) {
|
|
debug("Using fixed link, skip link adjust\n");
|
|
return;
|
|
}
|
|
|
|
if (phydev->link) {
|
|
if ((pp->speed != phydev->speed) ||
|
|
(pp->duplex != phydev->duplex)) {
|
|
u32 val;
|
|
|
|
val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
|
|
val &= ~(MVNETA_GMAC_CONFIG_MII_SPEED |
|
|
MVNETA_GMAC_CONFIG_GMII_SPEED |
|
|
MVNETA_GMAC_CONFIG_FULL_DUPLEX |
|
|
MVNETA_GMAC_AN_SPEED_EN |
|
|
MVNETA_GMAC_AN_DUPLEX_EN);
|
|
|
|
if (phydev->duplex)
|
|
val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
|
|
|
|
if (phydev->speed == SPEED_1000)
|
|
val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
|
|
else
|
|
val |= MVNETA_GMAC_CONFIG_MII_SPEED;
|
|
|
|
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
|
|
|
|
pp->duplex = phydev->duplex;
|
|
pp->speed = phydev->speed;
|
|
}
|
|
}
|
|
|
|
if (phydev->link != pp->link) {
|
|
if (!phydev->link) {
|
|
pp->duplex = -1;
|
|
pp->speed = 0;
|
|
}
|
|
|
|
pp->link = phydev->link;
|
|
status_change = 1;
|
|
}
|
|
|
|
if (status_change) {
|
|
if (phydev->link) {
|
|
u32 val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
|
|
val |= (MVNETA_GMAC_FORCE_LINK_PASS |
|
|
MVNETA_GMAC_FORCE_LINK_DOWN);
|
|
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
|
|
mvneta_port_up(pp);
|
|
} else {
|
|
mvneta_port_down(pp);
|
|
}
|
|
}
|
|
}
|
|
|
|
static int mvneta_open(struct udevice *dev)
|
|
{
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
int ret;
|
|
|
|
ret = mvneta_setup_rxqs(pp);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = mvneta_setup_txqs(pp);
|
|
if (ret)
|
|
return ret;
|
|
|
|
mvneta_adjust_link(dev);
|
|
|
|
mvneta_start_dev(pp);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Initialize hw */
|
|
static int mvneta_init2(struct mvneta_port *pp)
|
|
{
|
|
int queue;
|
|
|
|
/* Disable port */
|
|
mvneta_port_disable(pp);
|
|
|
|
/* Set port default values */
|
|
mvneta_defaults_set(pp);
|
|
|
|
pp->txqs = kzalloc(txq_number * sizeof(struct mvneta_tx_queue),
|
|
GFP_KERNEL);
|
|
if (!pp->txqs)
|
|
return -ENOMEM;
|
|
|
|
/* U-Boot special: use preallocated area */
|
|
pp->txqs[0].descs = buffer_loc.tx_descs;
|
|
|
|
/* Initialize TX descriptor rings */
|
|
for (queue = 0; queue < txq_number; queue++) {
|
|
struct mvneta_tx_queue *txq = &pp->txqs[queue];
|
|
txq->id = queue;
|
|
txq->size = pp->tx_ring_size;
|
|
}
|
|
|
|
pp->rxqs = kzalloc(rxq_number * sizeof(struct mvneta_rx_queue),
|
|
GFP_KERNEL);
|
|
if (!pp->rxqs) {
|
|
kfree(pp->txqs);
|
|
return -ENOMEM;
|
|
}
|
|
|
|
/* U-Boot special: use preallocated area */
|
|
pp->rxqs[0].descs = buffer_loc.rx_descs;
|
|
|
|
/* Create Rx descriptor rings */
|
|
for (queue = 0; queue < rxq_number; queue++) {
|
|
struct mvneta_rx_queue *rxq = &pp->rxqs[queue];
|
|
rxq->id = queue;
|
|
rxq->size = pp->rx_ring_size;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* platform glue : initialize decoding windows */
|
|
|
|
/*
|
|
* Not like A380, in Armada3700, there are two layers of decode windows for GBE:
|
|
* First layer is: GbE Address window that resides inside the GBE unit,
|
|
* Second layer is: Fabric address window which is located in the NIC400
|
|
* (South Fabric).
|
|
* To simplify the address decode configuration for Armada3700, we bypass the
|
|
* first layer of GBE decode window by setting the first window to 4GB.
|
|
*/
|
|
static void mvneta_bypass_mbus_windows(struct mvneta_port *pp)
|
|
{
|
|
/*
|
|
* Set window size to 4GB, to bypass GBE address decode, leave the
|
|
* work to MBUS decode window
|
|
*/
|
|
mvreg_write(pp, MVNETA_WIN_SIZE(0), MVNETA_WIN_SIZE_MASK);
|
|
|
|
/* Enable GBE address decode window 0 by set bit 0 to 0 */
|
|
clrbits_le32(pp->base + MVNETA_BASE_ADDR_ENABLE,
|
|
MVNETA_BASE_ADDR_ENABLE_BIT);
|
|
|
|
/* Set GBE address decode window 0 to full Access (read or write) */
|
|
setbits_le32(pp->base + MVNETA_PORT_ACCESS_PROTECT,
|
|
MVNETA_PORT_ACCESS_PROTECT_WIN0_RW);
|
|
}
|
|
|
|
static void mvneta_conf_mbus_windows(struct mvneta_port *pp)
|
|
{
|
|
const struct mbus_dram_target_info *dram;
|
|
u32 win_enable;
|
|
u32 win_protect;
|
|
int i;
|
|
|
|
dram = mvebu_mbus_dram_info();
|
|
for (i = 0; i < 6; i++) {
|
|
mvreg_write(pp, MVNETA_WIN_BASE(i), 0);
|
|
mvreg_write(pp, MVNETA_WIN_SIZE(i), 0);
|
|
|
|
if (i < 4)
|
|
mvreg_write(pp, MVNETA_WIN_REMAP(i), 0);
|
|
}
|
|
|
|
win_enable = 0x3f;
|
|
win_protect = 0;
|
|
|
|
for (i = 0; i < dram->num_cs; i++) {
|
|
const struct mbus_dram_window *cs = dram->cs + i;
|
|
mvreg_write(pp, MVNETA_WIN_BASE(i), (cs->base & 0xffff0000) |
|
|
(cs->mbus_attr << 8) | dram->mbus_dram_target_id);
|
|
|
|
mvreg_write(pp, MVNETA_WIN_SIZE(i),
|
|
(cs->size - 1) & 0xffff0000);
|
|
|
|
win_enable &= ~(1 << i);
|
|
win_protect |= 3 << (2 * i);
|
|
}
|
|
|
|
mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable);
|
|
}
|
|
|
|
/* Power up the port */
|
|
static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
|
|
{
|
|
u32 ctrl;
|
|
|
|
/* MAC Cause register should be cleared */
|
|
mvreg_write(pp, MVNETA_UNIT_INTR_CAUSE, 0);
|
|
|
|
ctrl = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
|
|
|
|
/* Even though it might look weird, when we're configured in
|
|
* SGMII or QSGMII mode, the RGMII bit needs to be set.
|
|
*/
|
|
switch (phy_mode) {
|
|
case PHY_INTERFACE_MODE_QSGMII:
|
|
mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_QSGMII_SERDES_PROTO);
|
|
ctrl |= MVNETA_GMAC2_PCS_ENABLE | MVNETA_GMAC2_PORT_RGMII;
|
|
break;
|
|
case PHY_INTERFACE_MODE_SGMII:
|
|
mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_SGMII_SERDES_PROTO);
|
|
ctrl |= MVNETA_GMAC2_PCS_ENABLE | MVNETA_GMAC2_PORT_RGMII;
|
|
break;
|
|
case PHY_INTERFACE_MODE_RGMII:
|
|
case PHY_INTERFACE_MODE_RGMII_ID:
|
|
ctrl |= MVNETA_GMAC2_PORT_RGMII;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* Cancel Port Reset */
|
|
ctrl &= ~MVNETA_GMAC2_PORT_RESET;
|
|
mvreg_write(pp, MVNETA_GMAC_CTRL_2, ctrl);
|
|
|
|
while ((mvreg_read(pp, MVNETA_GMAC_CTRL_2) &
|
|
MVNETA_GMAC2_PORT_RESET) != 0)
|
|
continue;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Device initialization routine */
|
|
static int mvneta_init(struct udevice *dev)
|
|
{
|
|
struct eth_pdata *pdata = dev_get_platdata(dev);
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
int err;
|
|
|
|
pp->tx_ring_size = MVNETA_MAX_TXD;
|
|
pp->rx_ring_size = MVNETA_MAX_RXD;
|
|
|
|
err = mvneta_init2(pp);
|
|
if (err < 0) {
|
|
dev_err(&pdev->dev, "can't init eth hal\n");
|
|
return err;
|
|
}
|
|
|
|
mvneta_mac_addr_set(pp, pdata->enetaddr, rxq_def);
|
|
|
|
err = mvneta_port_power_up(pp, pp->phy_interface);
|
|
if (err < 0) {
|
|
dev_err(&pdev->dev, "can't power up port\n");
|
|
return err;
|
|
}
|
|
|
|
/* Call open() now as it needs to be done before runing send() */
|
|
mvneta_open(dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* U-Boot only functions follow here */
|
|
|
|
/* SMI / MDIO functions */
|
|
|
|
static int smi_wait_ready(struct mvneta_port *pp)
|
|
{
|
|
u32 timeout = MVNETA_SMI_TIMEOUT;
|
|
u32 smi_reg;
|
|
|
|
/* wait till the SMI is not busy */
|
|
do {
|
|
/* read smi register */
|
|
smi_reg = mvreg_read(pp, MVNETA_SMI);
|
|
if (timeout-- == 0) {
|
|
printf("Error: SMI busy timeout\n");
|
|
return -EFAULT;
|
|
}
|
|
} while (smi_reg & MVNETA_SMI_BUSY);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* mvneta_mdio_read - miiphy_read callback function.
|
|
*
|
|
* Returns 16bit phy register value, or 0xffff on error
|
|
*/
|
|
static int mvneta_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
|
|
{
|
|
struct mvneta_port *pp = bus->priv;
|
|
u32 smi_reg;
|
|
u32 timeout;
|
|
|
|
/* check parameters */
|
|
if (addr > MVNETA_PHY_ADDR_MASK) {
|
|
printf("Error: Invalid PHY address %d\n", addr);
|
|
return -EFAULT;
|
|
}
|
|
|
|
if (reg > MVNETA_PHY_REG_MASK) {
|
|
printf("Err: Invalid register offset %d\n", reg);
|
|
return -EFAULT;
|
|
}
|
|
|
|
/* wait till the SMI is not busy */
|
|
if (smi_wait_ready(pp) < 0)
|
|
return -EFAULT;
|
|
|
|
/* fill the phy address and regiser offset and read opcode */
|
|
smi_reg = (addr << MVNETA_SMI_DEV_ADDR_OFFS)
|
|
| (reg << MVNETA_SMI_REG_ADDR_OFFS)
|
|
| MVNETA_SMI_OPCODE_READ;
|
|
|
|
/* write the smi register */
|
|
mvreg_write(pp, MVNETA_SMI, smi_reg);
|
|
|
|
/* wait till read value is ready */
|
|
timeout = MVNETA_SMI_TIMEOUT;
|
|
|
|
do {
|
|
/* read smi register */
|
|
smi_reg = mvreg_read(pp, MVNETA_SMI);
|
|
if (timeout-- == 0) {
|
|
printf("Err: SMI read ready timeout\n");
|
|
return -EFAULT;
|
|
}
|
|
} while (!(smi_reg & MVNETA_SMI_READ_VALID));
|
|
|
|
/* Wait for the data to update in the SMI register */
|
|
for (timeout = 0; timeout < MVNETA_SMI_TIMEOUT; timeout++)
|
|
;
|
|
|
|
return mvreg_read(pp, MVNETA_SMI) & MVNETA_SMI_DATA_MASK;
|
|
}
|
|
|
|
/*
|
|
* mvneta_mdio_write - miiphy_write callback function.
|
|
*
|
|
* Returns 0 if write succeed, -EINVAL on bad parameters
|
|
* -ETIME on timeout
|
|
*/
|
|
static int mvneta_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
|
|
u16 value)
|
|
{
|
|
struct mvneta_port *pp = bus->priv;
|
|
u32 smi_reg;
|
|
|
|
/* check parameters */
|
|
if (addr > MVNETA_PHY_ADDR_MASK) {
|
|
printf("Error: Invalid PHY address %d\n", addr);
|
|
return -EFAULT;
|
|
}
|
|
|
|
if (reg > MVNETA_PHY_REG_MASK) {
|
|
printf("Err: Invalid register offset %d\n", reg);
|
|
return -EFAULT;
|
|
}
|
|
|
|
/* wait till the SMI is not busy */
|
|
if (smi_wait_ready(pp) < 0)
|
|
return -EFAULT;
|
|
|
|
/* fill the phy addr and reg offset and write opcode and data */
|
|
smi_reg = value << MVNETA_SMI_DATA_OFFS;
|
|
smi_reg |= (addr << MVNETA_SMI_DEV_ADDR_OFFS)
|
|
| (reg << MVNETA_SMI_REG_ADDR_OFFS);
|
|
smi_reg &= ~MVNETA_SMI_OPCODE_READ;
|
|
|
|
/* write the smi register */
|
|
mvreg_write(pp, MVNETA_SMI, smi_reg);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mvneta_start(struct udevice *dev)
|
|
{
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
struct phy_device *phydev;
|
|
|
|
mvneta_port_power_up(pp, pp->phy_interface);
|
|
|
|
if (!pp->init || pp->link == 0) {
|
|
if (mvneta_port_is_fixed_link(pp)) {
|
|
u32 val;
|
|
|
|
pp->init = 1;
|
|
pp->link = 1;
|
|
mvneta_init(dev);
|
|
|
|
val = MVNETA_GMAC_FORCE_LINK_UP |
|
|
MVNETA_GMAC_IB_BYPASS_AN_EN |
|
|
MVNETA_GMAC_SET_FC_EN |
|
|
MVNETA_GMAC_ADVERT_FC_EN |
|
|
MVNETA_GMAC_SAMPLE_TX_CFG_EN;
|
|
|
|
if (pp->duplex)
|
|
val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
|
|
|
|
if (pp->speed == SPEED_1000)
|
|
val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
|
|
else if (pp->speed == SPEED_100)
|
|
val |= MVNETA_GMAC_CONFIG_MII_SPEED;
|
|
|
|
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
|
|
} else {
|
|
/* Set phy address of the port */
|
|
mvreg_write(pp, MVNETA_PHY_ADDR, pp->phyaddr);
|
|
|
|
phydev = phy_connect(pp->bus, pp->phyaddr, dev,
|
|
pp->phy_interface);
|
|
if (!phydev) {
|
|
printf("phy_connect failed\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
pp->phydev = phydev;
|
|
phy_config(phydev);
|
|
phy_startup(phydev);
|
|
if (!phydev->link) {
|
|
printf("%s: No link.\n", phydev->dev->name);
|
|
return -1;
|
|
}
|
|
|
|
/* Full init on first call */
|
|
mvneta_init(dev);
|
|
pp->init = 1;
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
/* Upon all following calls, this is enough */
|
|
mvneta_port_up(pp);
|
|
mvneta_port_enable(pp);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mvneta_send(struct udevice *dev, void *packet, int length)
|
|
{
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
struct mvneta_tx_queue *txq = &pp->txqs[0];
|
|
struct mvneta_tx_desc *tx_desc;
|
|
int sent_desc;
|
|
u32 timeout = 0;
|
|
|
|
/* Get a descriptor for the first part of the packet */
|
|
tx_desc = mvneta_txq_next_desc_get(txq);
|
|
|
|
tx_desc->buf_phys_addr = (u32)(uintptr_t)packet;
|
|
tx_desc->data_size = length;
|
|
flush_dcache_range((ulong)packet,
|
|
(ulong)packet + ALIGN(length, PKTALIGN));
|
|
|
|
/* First and Last descriptor */
|
|
tx_desc->command = MVNETA_TX_L4_CSUM_NOT | MVNETA_TXD_FLZ_DESC;
|
|
mvneta_txq_pend_desc_add(pp, txq, 1);
|
|
|
|
/* Wait for packet to be sent (queue might help with speed here) */
|
|
sent_desc = mvneta_txq_sent_desc_num_get(pp, txq);
|
|
while (!sent_desc) {
|
|
if (timeout++ > 10000) {
|
|
printf("timeout: packet not sent\n");
|
|
return -1;
|
|
}
|
|
sent_desc = mvneta_txq_sent_desc_num_get(pp, txq);
|
|
}
|
|
|
|
/* txDone has increased - hw sent packet */
|
|
mvneta_txq_sent_desc_dec(pp, txq, sent_desc);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
|
|
{
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
int rx_done;
|
|
struct mvneta_rx_queue *rxq;
|
|
int rx_bytes = 0;
|
|
|
|
/* get rx queue */
|
|
rxq = mvneta_rxq_handle_get(pp, rxq_def);
|
|
rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq);
|
|
|
|
if (rx_done) {
|
|
struct mvneta_rx_desc *rx_desc;
|
|
unsigned char *data;
|
|
u32 rx_status;
|
|
|
|
/*
|
|
* No cache invalidation needed here, since the desc's are
|
|
* located in a uncached memory region
|
|
*/
|
|
rx_desc = mvneta_rxq_next_desc_get(rxq);
|
|
|
|
rx_status = rx_desc->status;
|
|
if (!mvneta_rxq_desc_is_first_last(rx_status) ||
|
|
(rx_status & MVNETA_RXD_ERR_SUMMARY)) {
|
|
mvneta_rx_error(pp, rx_desc);
|
|
/* leave the descriptor untouched */
|
|
return -EIO;
|
|
}
|
|
|
|
/* 2 bytes for marvell header. 4 bytes for crc */
|
|
rx_bytes = rx_desc->data_size - 6;
|
|
|
|
/* give packet to stack - skip on first 2 bytes */
|
|
data = (u8 *)(uintptr_t)rx_desc->buf_cookie + 2;
|
|
/*
|
|
* No cache invalidation needed here, since the rx_buffer's are
|
|
* located in a uncached memory region
|
|
*/
|
|
*packetp = data;
|
|
|
|
/*
|
|
* Only mark one descriptor as free
|
|
* since only one was processed
|
|
*/
|
|
mvneta_rxq_desc_num_update(pp, rxq, 1, 1);
|
|
}
|
|
|
|
return rx_bytes;
|
|
}
|
|
|
|
static int mvneta_probe(struct udevice *dev)
|
|
{
|
|
struct eth_pdata *pdata = dev_get_platdata(dev);
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
void *blob = (void *)gd->fdt_blob;
|
|
int node = dev_of_offset(dev);
|
|
struct mii_dev *bus;
|
|
unsigned long addr;
|
|
void *bd_space;
|
|
int ret;
|
|
int fl_node;
|
|
|
|
/*
|
|
* Allocate buffer area for descs and rx_buffers. This is only
|
|
* done once for all interfaces. As only one interface can
|
|
* be active. Make this area DMA safe by disabling the D-cache
|
|
*/
|
|
if (!buffer_loc.tx_descs) {
|
|
u32 size;
|
|
|
|
/* Align buffer area for descs and rx_buffers to 1MiB */
|
|
bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
|
|
flush_dcache_range((ulong)bd_space, (ulong)bd_space + BD_SPACE);
|
|
mmu_set_region_dcache_behaviour((phys_addr_t)bd_space, BD_SPACE,
|
|
DCACHE_OFF);
|
|
buffer_loc.tx_descs = (struct mvneta_tx_desc *)bd_space;
|
|
size = roundup(MVNETA_MAX_TXD * sizeof(struct mvneta_tx_desc),
|
|
ARCH_DMA_MINALIGN);
|
|
memset(buffer_loc.tx_descs, 0, size);
|
|
buffer_loc.rx_descs = (struct mvneta_rx_desc *)
|
|
((phys_addr_t)bd_space + size);
|
|
size += roundup(MVNETA_MAX_RXD * sizeof(struct mvneta_rx_desc),
|
|
ARCH_DMA_MINALIGN);
|
|
buffer_loc.rx_buffers = (phys_addr_t)(bd_space + size);
|
|
}
|
|
|
|
pp->base = (void __iomem *)pdata->iobase;
|
|
|
|
/* Configure MBUS address windows */
|
|
if (device_is_compatible(dev, "marvell,armada-3700-neta"))
|
|
mvneta_bypass_mbus_windows(pp);
|
|
else
|
|
mvneta_conf_mbus_windows(pp);
|
|
|
|
/* PHY interface is already decoded in mvneta_ofdata_to_platdata() */
|
|
pp->phy_interface = pdata->phy_interface;
|
|
|
|
/* fetch 'fixed-link' property from 'neta' node */
|
|
fl_node = fdt_subnode_offset(blob, node, "fixed-link");
|
|
if (fl_node != -FDT_ERR_NOTFOUND) {
|
|
/* set phy_addr to invalid value for fixed link */
|
|
pp->phyaddr = PHY_MAX_ADDR + 1;
|
|
pp->duplex = fdtdec_get_bool(blob, fl_node, "full-duplex");
|
|
pp->speed = fdtdec_get_int(blob, fl_node, "speed", 0);
|
|
} else {
|
|
/* Now read phyaddr from DT */
|
|
addr = fdtdec_get_int(blob, node, "phy", 0);
|
|
addr = fdt_node_offset_by_phandle(blob, addr);
|
|
pp->phyaddr = fdtdec_get_int(blob, addr, "reg", 0);
|
|
}
|
|
|
|
bus = mdio_alloc();
|
|
if (!bus) {
|
|
printf("Failed to allocate MDIO bus\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
bus->read = mvneta_mdio_read;
|
|
bus->write = mvneta_mdio_write;
|
|
snprintf(bus->name, sizeof(bus->name), dev->name);
|
|
bus->priv = (void *)pp;
|
|
pp->bus = bus;
|
|
|
|
ret = mdio_register(bus);
|
|
if (ret)
|
|
return ret;
|
|
|
|
#if CONFIG_IS_ENABLED(DM_GPIO)
|
|
gpio_request_by_name(dev, "phy-reset-gpios", 0,
|
|
&pp->phy_reset_gpio, GPIOD_IS_OUT);
|
|
|
|
if (dm_gpio_is_valid(&pp->phy_reset_gpio)) {
|
|
dm_gpio_set_value(&pp->phy_reset_gpio, 1);
|
|
mdelay(10);
|
|
dm_gpio_set_value(&pp->phy_reset_gpio, 0);
|
|
}
|
|
#endif
|
|
|
|
return board_network_enable(bus);
|
|
}
|
|
|
|
static void mvneta_stop(struct udevice *dev)
|
|
{
|
|
struct mvneta_port *pp = dev_get_priv(dev);
|
|
|
|
mvneta_port_down(pp);
|
|
mvneta_port_disable(pp);
|
|
}
|
|
|
|
static const struct eth_ops mvneta_ops = {
|
|
.start = mvneta_start,
|
|
.send = mvneta_send,
|
|
.recv = mvneta_recv,
|
|
.stop = mvneta_stop,
|
|
.write_hwaddr = mvneta_write_hwaddr,
|
|
};
|
|
|
|
static int mvneta_ofdata_to_platdata(struct udevice *dev)
|
|
{
|
|
struct eth_pdata *pdata = dev_get_platdata(dev);
|
|
const char *phy_mode;
|
|
|
|
pdata->iobase = dev_read_addr(dev);
|
|
|
|
/* Get phy-mode / phy_interface from DT */
|
|
pdata->phy_interface = -1;
|
|
phy_mode = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), "phy-mode",
|
|
NULL);
|
|
if (phy_mode)
|
|
pdata->phy_interface = phy_get_interface_by_name(phy_mode);
|
|
if (pdata->phy_interface == -1) {
|
|
debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
|
|
return -EINVAL;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct udevice_id mvneta_ids[] = {
|
|
{ .compatible = "marvell,armada-370-neta" },
|
|
{ .compatible = "marvell,armada-xp-neta" },
|
|
{ .compatible = "marvell,armada-3700-neta" },
|
|
{ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(mvneta) = {
|
|
.name = "mvneta",
|
|
.id = UCLASS_ETH,
|
|
.of_match = mvneta_ids,
|
|
.ofdata_to_platdata = mvneta_ofdata_to_platdata,
|
|
.probe = mvneta_probe,
|
|
.ops = &mvneta_ops,
|
|
.priv_auto_alloc_size = sizeof(struct mvneta_port),
|
|
.platdata_auto_alloc_size = sizeof(struct eth_pdata),
|
|
};
|