380e32b171
Two defconfigs were missed when transitioning the SYS_FMAN_FW_ADDR
symbol to Kconfig. CONFIG_SYS_FMAN_FW_ADDR is currently initialized to
0 by default on these builds, which prevents the firmware from loading.
Add the correct symbols to these defconfigs.
Fixes: a97a071d10 ("configs: fsl: migrate FMAN/QE specific defines to Kconfig")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
85 lines
2.2 KiB
Plaintext
85 lines
2.2 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_COUNTER_FREQUENCY=25000000
|
|
CONFIG_TARGET_LS1046AFRWY=y
|
|
CONFIG_TFABOOT=y
|
|
CONFIG_SYS_TEXT_BASE=0x82000000
|
|
CONFIG_SYS_MALLOC_LEN=0x102000
|
|
CONFIG_NR_DRAM_BANKS=2
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x500000
|
|
CONFIG_ENV_SECT_SIZE=0x40000
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-frwy"
|
|
CONFIG_FSL_USE_PCA9547_MUX=y
|
|
CONFIG_QSPI_AHB_INIT=y
|
|
CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
|
|
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
|
|
CONFIG_ENV_ADDR=0x40500000
|
|
CONFIG_AHCI=y
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_REMAKE_ELF=y
|
|
CONFIG_MP=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_BOOTDELAY=10
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=1550000.spi:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)"
|
|
CONFIG_ARCH_MISC_INIT=y
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.spi:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)"
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_USE_ETHPRIME=y
|
|
CONFIG_ETHPRIME="FM1@DTSEC3"
|
|
CONFIG_DM=y
|
|
CONFIG_SATA=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_FSL_CAAM=y
|
|
# CONFIG_DDR_SPD is not set
|
|
CONFIG_MPC8XXX_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x52
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_FSL_IFC=y
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
# CONFIG_SPI_FLASH_BAR is not set
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_VITESSE=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_E1000=y
|
|
CONFIG_FMAN_ENET=y
|
|
CONFIG_SYS_FMAN_FW_ADDR=0x900000
|
|
CONFIG_NVME_PCI=y
|
|
CONFIG_PCI=y
|
|
CONFIG_DM_PCI_COMPAT=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_PCIE_LAYERSCAPE_EP=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|
|
CONFIG_USB_HOST_ETHER=y
|
|
CONFIG_USB_ETHER_ASIX=y
|
|
CONFIG_USB_ETHER_ASIX88179=y
|
|
CONFIG_USB_ETHER_RTL8152=y
|