a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
100 lines
2.4 KiB
C
100 lines
2.4 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
|
|
*/
|
|
|
|
#ifndef _CONFIG_SYNOLOGY_DS414_H
|
|
#define _CONFIG_SYNOLOGY_DS414_H
|
|
|
|
/*
|
|
* High Level Configuration Options (easy to change)
|
|
*/
|
|
|
|
/*
|
|
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
|
|
* for DDR ECC byte filling in the SPL before loading the main
|
|
* U-Boot into it.
|
|
*/
|
|
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
|
|
|
|
/*
|
|
* Commands configuration
|
|
*/
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_MVTWSI
|
|
#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
|
|
#define CONFIG_SYS_I2C_SLAVE 0x0
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
/* Environment in SPI NOR flash */
|
|
|
|
#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII
|
|
|
|
/* PCIe support */
|
|
#ifndef CONFIG_SPL_BUILD
|
|
#define CONFIG_PCI_SCAN_SHOW
|
|
#endif
|
|
|
|
/* USB/EHCI/XHCI configuration */
|
|
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
|
|
/* FIXME: broken XHCI support
|
|
* Below defines should enable support for the two rear USB3 ports. Sadly, this
|
|
* does not work because:
|
|
* - xhci-pci seems to not support DM_USB, so with that enabled it is not
|
|
* found.
|
|
* - USB init fails, controller does not respond in time */
|
|
|
|
#if !defined(CONFIG_USB_XHCI_HCD)
|
|
#define CONFIG_EHCI_IS_TDI
|
|
#endif
|
|
|
|
/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
|
|
|
|
/*
|
|
* mv-common.h should be defined after CMD configs since it used them
|
|
* to enable certain macros
|
|
*/
|
|
#include "mv-common.h"
|
|
|
|
/*
|
|
* Memory layout while starting into the bin_hdr via the
|
|
* BootROM:
|
|
*
|
|
* 0x4000.4000 - 0x4003.4000 headers space (192KiB)
|
|
* 0x4000.4030 bin_hdr start address
|
|
* 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB)
|
|
* 0x4007.fffc BootROM stack top
|
|
*
|
|
* The address space between 0x4007.fffc and 0x400f.fff is not locked in
|
|
* L2 cache thus cannot be used.
|
|
*/
|
|
|
|
/* SPL */
|
|
/* Defines for SPL */
|
|
#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
|
|
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#define CONFIG_SYS_MALLOC_SIMPLE
|
|
#endif
|
|
|
|
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
|
|
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
|
|
|
|
/* SPL related SPI defines */
|
|
|
|
/* DS414 bus width is 32bits */
|
|
#define CONFIG_DDR_32BIT
|
|
|
|
/* Default Environment */
|
|
#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm"
|
|
#define CONFIG_LOADADDR 0x80000
|
|
|
|
#endif /* _CONFIG_SYNOLOGY_DS414_H */
|