0613c36a7a
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS Signed-off-by: Tom Rini <trini@konsulko.com>
136 lines
4.0 KiB
C
136 lines
4.0 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
|
|
* Hayden Fraser (Hayden.Fraser@freescale.com)
|
|
*/
|
|
|
|
#ifndef _M5253DEMO_H
|
|
#define _M5253DEMO_H
|
|
|
|
#include <linux/stringify.h>
|
|
|
|
#define CFG_SYS_UART_PORT (0)
|
|
|
|
|
|
/* Configuration for environment
|
|
* Environment is embedded in u-boot in the second sector of the flash
|
|
*/
|
|
|
|
#define LDS_BOARD_TEXT \
|
|
. = DEFINED(env_offset) ? env_offset : .; \
|
|
env/embedded.o(.text*);
|
|
|
|
#ifdef CONFIG_DRIVER_DM9000
|
|
# define CFG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
|
|
"loadaddr=10000\0" \
|
|
"u-boot=u-boot.bin\0" \
|
|
"load=tftp ${loadaddr) ${u-boot}\0" \
|
|
"upd=run load; run prog\0" \
|
|
"prog=prot off 0xff800000 0xff82ffff;" \
|
|
"era 0xff800000 0xff82ffff;" \
|
|
"cp.b ${loadaddr} 0xff800000 ${filesize};" \
|
|
"save\0" \
|
|
""
|
|
#endif
|
|
|
|
/* I2C */
|
|
#define CFG_SYS_I2C_PINMUX_REG (*(u32 *) (CFG_SYS_MBAR+0x19C))
|
|
#define CFG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF)
|
|
#define CFG_SYS_I2C_PINMUX_SET (0)
|
|
|
|
#undef CFG_SYS_PLL_BYPASS /* bypass PLL for test purpose */
|
|
#define CFG_SYS_FAST_CLK
|
|
#ifdef CFG_SYS_FAST_CLK
|
|
# define CFG_SYS_PLLCR 0x1243E054
|
|
# define CFG_SYS_CLK 140000000
|
|
#else
|
|
# define CFG_SYS_PLLCR 0x135a4140
|
|
# define CFG_SYS_CLK 70000000
|
|
#endif
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
|
|
#define CFG_SYS_MBAR 0x10000000 /* Register Base Addrs */
|
|
#define CFG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */
|
|
|
|
/*
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CFG_SYS_INIT_RAM_ADDR 0x20000000
|
|
#define CFG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
|
|
|
|
/*
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CFG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CFG_SYS_SDRAM_BASE 0x00000000
|
|
#define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization ??
|
|
*/
|
|
#define CFG_SYS_BOOTMAPSZ (CFG_SYS_SDRAM_BASE + (CFG_SYS_SDRAM_SIZE << 20))
|
|
|
|
/* FLASH organization */
|
|
#define CFG_SYS_FLASH_BASE (CFG_SYS_CS0_BASE)
|
|
|
|
#define FLASH_SST6401B 0x200
|
|
#define SST_ID_xF6401B 0x236D236D
|
|
|
|
#ifdef CONFIG_SYS_FLASH_CFI
|
|
/*
|
|
* Unable to use CFI driver, due to incompatible sector erase command by SST.
|
|
* Amd/Atmel use 0x30 for sector erase, SST use 0x50.
|
|
* 0x30 is block erase in SST
|
|
*/
|
|
# define CFG_SYS_FLASH_SIZE 0x800000
|
|
#else
|
|
# define CFG_SYS_SST_SECT 2048
|
|
# define CFG_SYS_SST_SECTSZ 0x1000
|
|
#endif
|
|
|
|
/* Cache Configuration */
|
|
|
|
#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
|
|
CFG_SYS_INIT_RAM_SIZE - 8)
|
|
#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
|
|
CFG_SYS_INIT_RAM_SIZE - 4)
|
|
#define CFG_SYS_ICACHE_INV (CF_CACR_DCM)
|
|
#define CFG_SYS_CACHE_ACR0 (CFG_SYS_FLASH_BASE | \
|
|
CF_ADDRMASK(8) | \
|
|
CF_ACR_EN | CF_ACR_SM_ALL)
|
|
#define CFG_SYS_CACHE_ACR1 (CFG_SYS_SDRAM_BASE | \
|
|
CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
|
|
CF_ACR_EN | CF_ACR_SM_ALL)
|
|
#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \
|
|
CF_CACR_DBWE)
|
|
|
|
#define CFG_SYS_CS0_BASE 0xFF800000
|
|
#define CFG_SYS_CS0_MASK 0x007F0021
|
|
#define CFG_SYS_CS0_CTRL 0x00001D80
|
|
|
|
#define CFG_SYS_CS1_BASE 0xE0000000
|
|
#define CFG_SYS_CS1_MASK 0x00000001
|
|
#define CFG_SYS_CS1_CTRL 0x00003DD8
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Port configuration
|
|
*/
|
|
#define CFG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
|
|
#define CFG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */
|
|
#define CFG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */
|
|
#define CFG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */
|
|
#define CFG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */
|
|
#define CFG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
|
|
#define CFG_SYS_GPIO1_LED 0x00400000 /* user led */
|
|
|
|
#endif /* _M5253DEMO_H */
|