leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
master
u-boot/drivers/video/logicore_dp_tx.c
Simon Glass 41575d8e4c dm: treewide: Rename auto_alloc_size members to be shorter 
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.

Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 08:00:25 -07:00

2298 lines
66 KiB
C
Raw Permalink Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* logicore_dp_tx.c
*
* Driver for XILINX LogiCore DisplayPort v6.1 TX (Source)
* based on Xilinx dp_v3_1 driver sources, updated to dp_v4_0
*
* (C) Copyright 2016
* Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
*/
#include <common.h>
#include <clk.h>
#include <display.h>
#include <dm.h>
#include <errno.h>
#include <linux/delay.h>
#include "axi.h"
#include "logicore_dp_dpcd.h"
#include "logicore_dp_tx.h"
#include "logicore_dp_tx_regif.h"
/* Default AXI clock frequency value */
#define S_AXI_CLK_DEFAULT 100000000
/* Default DP phy clock value */
#define PHY_CLOCK_SELECT_DEFAULT PHY_CLOCK_SELECT_540GBPS
/* The maximum voltage swing level is 3 */
#define MAXIMUM_VS_LEVEL 3
/* The maximum pre-emphasis level is 3 */
#define MAXIMUM_PE_LEVEL 3
/* Error out if an AUX request yields a defer reply more than 50 times */
#define AUX_MAX_DEFER_COUNT 50
/* Error out if an AUX request times out more than 50 times awaiting a reply */
#define AUX_MAX_TIMEOUT_COUNT 50
/* Error out if checking for a connected device times out more than 50 times */
#define IS_CONNECTED_MAX_TIMEOUT_COUNT 50
/**
* enum link_training_states - States for link training state machine
* @TS_CLOCK_RECOVERY: State for clock recovery
* @TS_CHANNEL_EQUALIZATION: State for channel equalization
* @TS_ADJUST_LINK_RATE: State where link rate is reduced in reaction to
* failed link training
* @TS_ADJUST_LANE_COUNT: State where lane count is reduced in reaction to
* failed link training
* @TS_FAILURE: State of link training failure
* @TS_SUCCESS:: State for successfully completed link training
*/
enum link_training_states {
TS_CLOCK_RECOVERY,
TS_CHANNEL_EQUALIZATION,
TS_ADJUST_LINK_RATE,
TS_ADJUST_LANE_COUNT,
TS_FAILURE,
TS_SUCCESS
};
/**
* struct aux_transaction - Description of an AUX channel transaction
* @cmd_code: Command code of the transaction
* @num_bytes: The number of bytes in the transaction's payload data
* @address: The DPCD address of the transaction
* @data: Payload data of the AUX channel transaction
*/
struct aux_transaction {
u16 cmd_code;
u8 num_bytes;
u32 address;
u8 *data;
};
/**
* struct main_stream_attributes - Main stream attributes
* @pixel_clock_hz: Pixel clock of the stream (in Hz)
* @misc_0: Miscellaneous stream attributes 0 as specified
* by the DisplayPort 1.2 specification
* @misc_1: Miscellaneous stream attributes 1 as specified
* by the DisplayPort 1.2 specification
* @n_vid: N value for the video stream
* @m_vid: M value used to recover the video clock from the
* link clock
* @user_pixel_width: Width of the user data input port
* @data_per_lane: Used to translate the number of pixels per line
* to the native internal 16-bit datapath
* @avg_bytes_per_tu: Average number of bytes per transfer unit,
* scaled up by a factor of 1000
* @transfer_unit_size: Size of the transfer unit in the framing logic
* In MST mode, this is also the number of time
* slots that are alloted in the payload ID table
* @init_wait: Number of initial wait cycles at the start of a
* new line by the framing logic
* @bits_per_color: Bits per color component
* @component_format: The component format currently in use by the
* video stream
* @dynamic_range: The dynamic range currently in use by the video
* stream
* @y_cb_cr_colorimetry: The YCbCr colorimetry currently in use by the
* video stream
* @synchronous_clock_mode: Synchronous clock mode is currently in use by
* the video stream
* @override_user_pixel_width: If set to 1, the value stored for
* user_pixel_width will be used as the pixel width
* @h_start: Horizontal blank start (pixels)
* @h_active: Horizontal active resolution (pixels)
* @h_sync_width: Horizontal sync width (pixels)
* @h_total: Horizontal total (pixels)
* @h_sync_polarity: Horizontal sync polarity (0=neg|1=pos)
* @v_start: Vertical blank start (in lines)
* @v_active: Vertical active resolution (lines)
* @v_sync_width: Vertical sync width (lines)
* @v_total: Vertical total (lines)
* @v_sync_polarity: Vertical sync polarity (0=neg|1=pos)
*
* All porch parameters have been removed, because our videodata is
* hstart/vstart based, and there is no benefit in keeping the porches
*/
struct main_stream_attributes {
u32 pixel_clock_hz;
u32 misc_0;
u32 misc_1;
u32 n_vid;
//u32 m_vid;
u32 user_pixel_width;
u32 data_per_lane;
u32 avg_bytes_per_tu;
u32 transfer_unit_size;
u32 init_wait;
u32 bits_per_color;
u8 component_format;
u8 dynamic_range;
u8 y_cb_cr_colorimetry;
u8 synchronous_clock_mode;
u8 override_user_pixel_width;
u32 h_start;
u16 h_active;
u16 h_sync_width;
u16 h_total;
bool h_sync_polarity;
u32 v_start;
u16 v_active;
u16 v_sync_width;
u16 v_total;
bool v_sync_polarity;
};
/**
* struct link_config - Description of link configuration
* @lane_count: Currently selected lane count for this link
* @link_rate: Currently selected link rate for this link
* @scrambler_en: Flag to determine whether the scrambler is
* enabled for this link
* @enhanced_framing_mode: Flag to determine whether enhanced framing
* mode is active for this link
* @max_lane_count: Maximum lane count for this link
* @max_link_rate: Maximum link rate for this link
* @support_enhanced_framing_mode: Flag to indicate whether the link supports
* enhanced framing mode
* @vs_level: Voltage swing for each lane
* @pe_level: Pre-emphasis/cursor level for each lane
*/
struct link_config {
u8 lane_count;
u8 link_rate;
bool scrambler_en;
bool enhanced_framing_mode;
u8 max_lane_count;
u8 max_link_rate;
bool support_enhanced_framing_mode;
u8 vs_level;
u8 pe_level;
};
/**
* struct dp_tx - Private data structure of LogiCore DP TX devices
*
* @base: Address of register base of device
* @s_axi_clk: The AXI clock frequency in Hz
* @train_adaptive: Use adaptive link trainig (i.e. successively reduce
* link rate and/or lane count) for this device
* @max_link_rate: Maximum link rate for this device
* @max_lane_count: Maximum lane count for this device
* @dpcd_rx_caps: RX device's status registers, see below
* @lane_status_ajd_reqs: Lane status and adjustment requests information for
* this device
* @link_config: The link configuration for this device
* @main_stream_attributes: MSA set for this device
*
* dpcd_rx_caps is a raw read of the RX device's status registers. The first 4
* bytes correspond to the lane status associated with clock recovery, channel
* equalization, symbol lock, and interlane alignment. The remaining 2 bytes
* represent the pre-emphasis and voltage swing level adjustments requested by
* the RX device.
*/
struct dp_tx {
u32 base;
u32 s_axi_clk;
bool train_adaptive;
u8 max_link_rate;
u8 max_lane_count;
u8 dpcd_rx_caps[16];
u8 lane_status_ajd_reqs[6];
struct link_config link_config;
struct main_stream_attributes main_stream_attributes;
};
/*
* Internal API
*/
/**
* get_reg() - Read a register of a LogiCore DP TX device
* @dev: The LogiCore DP TX device in question
* @reg: The offset of the register to read
*
* Return: The read register value
*/
static u32 get_reg(struct udevice *dev, u32 reg)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u32 value = 0;
int res;
/* TODO(mario.six@gdsys.cc): error handling */
res = axi_read(dev->parent, dp_tx->base + reg, &value, AXI_SIZE_32);
if (res < 0)
printf("%s() failed; res = %d\n", __func__, res);
return value;
}
/**
* set_reg() - Write a register of a LogiCore DP TX device
* @dev: The LogiCore DP TX device in question
* @reg: The offset of the register to write
* @value: The value to write to the register
*/
static void set_reg(struct udevice *dev, u32 reg, u32 value)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
axi_write(dev->parent, dp_tx->base + reg, &value, AXI_SIZE_32);
}
/**
* is_connected() - Check if there is a connected RX device
* @dev: The LogiCore DP TX device in question
*
* The Xilinx original calls msleep_interruptible at least once, ignoring
* status.
*
* Return: true if a connected RX device was detected, false otherwise
*/
static bool is_connected(struct udevice *dev)
{
u8 retries = 0;
do {
int status = get_reg(dev, REG_INTERRUPT_SIG_STATE) &
INTERRUPT_SIG_STATE_HPD_STATE_MASK;
if (status)
return true;
udelay(1000);
} while (retries++ < IS_CONNECTED_MAX_TIMEOUT_COUNT);
return false;
}
/**
* wait_phy_ready() - Wait for the DisplayPort PHY to come out of reset
* @dev: The LogiCore DP TX device in question
* @mask: Bit mask specifying which bit in the status register should be waited
* for
*
* Return: 0 if wait succeeded, -ve if error occurred
*/
static int wait_phy_ready(struct udevice *dev, u32 mask)
{
u16 timeout = 20000;
u32 phy_status;
/* Wait until the PHY is ready. */
do {
phy_status = get_reg(dev, REG_PHY_STATUS) & mask;
/* Protect against an infinite loop. */
if (!timeout--)
return -ETIMEDOUT;
udelay(20);
} while (phy_status != mask);
return 0;
}
/* AUX channel access */
/**
* aux_wait_ready() - Wait until another request is no longer in progress
* @dev: The LogiCore DP TX device in question
*
* Return: 0 if wait succeeded, -ve if error occurred
*/
static int aux_wait_ready(struct udevice *dev)
{
int status;
u32 timeout = 100;
/* Wait until the DisplayPort TX core is ready. */
do {
status = get_reg(dev, REG_INTERRUPT_SIG_STATE);
/* Protect against an infinite loop. */
if (!timeout--)
return -ETIMEDOUT;
udelay(20);
} while (status & REPLY_STATUS_REPLY_IN_PROGRESS_MASK);
return 0;
}
/**
* aux_wait_reply() - Wait for reply on AUX channel
* @dev: The LogiCore DP TX device in question
*
* Wait for a reply indicating that the most recent AUX request
* has been received by the RX device.
*
* Return: 0 if wait succeeded, -ve if error occurred
*/
static int aux_wait_reply(struct udevice *dev)
{
u32 timeout = 100;
while (timeout > 0) {
int status = get_reg(dev, REG_REPLY_STATUS);
/* Check for error. */
if (status & REPLY_STATUS_REPLY_ERROR_MASK)
return -ETIMEDOUT;
/* Check for a reply. */
if ((status & REPLY_STATUS_REPLY_RECEIVED_MASK) &&
!(status &
REPLY_STATUS_REQUEST_IN_PROGRESS_MASK) &&
!(status &
REPLY_STATUS_REPLY_IN_PROGRESS_MASK)) {
return 0;
}
timeout--;
udelay(20);
}
return -ETIMEDOUT;
}
/**
* aux_request_send() - Send request on the AUX channel
* @dev: The LogiCore DP TX device in question
* @request: The request to send
*
* Submit the supplied AUX request to the RX device over the AUX
* channel by writing the command, the destination address, (the write buffer
* for write commands), and the data size to the DisplayPort TX core.
*
* This is the lower-level sending routine, which is called by aux_request().
*
* Return: 0 if request was sent successfully, -ve on error
*/
static int aux_request_send(struct udevice *dev,
struct aux_transaction *request)
{
u32 timeout_count;
int status;
u8 index;
/* Ensure that any pending AUX transactions have completed. */
timeout_count = 0;
do {
status = get_reg(dev, REG_REPLY_STATUS);
udelay(20);
timeout_count++;
if (timeout_count >= AUX_MAX_TIMEOUT_COUNT)
return -ETIMEDOUT;
} while ((status & REPLY_STATUS_REQUEST_IN_PROGRESS_MASK) ||
(status & REPLY_STATUS_REPLY_IN_PROGRESS_MASK));
set_reg(dev, REG_AUX_ADDRESS, request->address);
if (request->cmd_code == AUX_CMD_WRITE ||
request->cmd_code == AUX_CMD_I2C_WRITE ||
request->cmd_code == AUX_CMD_I2C_WRITE_MOT) {
/* Feed write data into the DisplayPort TX core's write FIFO. */
for (index = 0; index < request->num_bytes; index++) {
set_reg(dev,
REG_AUX_WRITE_FIFO, request->data[index]);
}
}
/* Submit the command and the data size. */
set_reg(dev, REG_AUX_CMD,
((request->cmd_code << AUX_CMD_SHIFT) |
((request->num_bytes - 1) &
AUX_CMD_NBYTES_TRANSFER_MASK)));
/* Check for a reply from the RX device to the submitted request. */
status = aux_wait_reply(dev);
if (status)
/* Waiting for a reply timed out. */
return -ETIMEDOUT;
/* Analyze the reply. */
status = get_reg(dev, REG_AUX_REPLY_CODE);
if (status == AUX_REPLY_CODE_DEFER ||
status == AUX_REPLY_CODE_I2C_DEFER) {
/* The request was deferred. */
return -EAGAIN;
} else if ((status == AUX_REPLY_CODE_NACK) ||
(status == AUX_REPLY_CODE_I2C_NACK)) {
/* The request was not acknowledged. */
return -EIO;
}
/* The request was acknowledged. */
if (request->cmd_code == AUX_CMD_READ ||
request->cmd_code == AUX_CMD_I2C_READ ||
request->cmd_code == AUX_CMD_I2C_READ_MOT) {
/* Wait until all data has been received. */
timeout_count = 0;
do {
status = get_reg(dev, REG_REPLY_DATA_COUNT);
udelay(100);
timeout_count++;
if (timeout_count >= AUX_MAX_TIMEOUT_COUNT)
return -ETIMEDOUT;
} while (status != request->num_bytes);
/* Obtain the read data from the reply FIFO. */
for (index = 0; index < request->num_bytes; index++)
request->data[index] = get_reg(dev, REG_AUX_REPLY_DATA);
}
return 0;
}
/**
* aux_request() - Submit request on the AUX channel
* @dev: The LogiCore DP TX device in question
* @request: The request to submit
*
* Submit the supplied AUX request to the RX device over the AUX
* channel. If waiting for a reply times out, or if the DisplayPort TX core
* indicates that the request was deferred, the request is sent again (up to a
* maximum specified by AUX_MAX_DEFER_COUNT|AUX_MAX_TIMEOUT_COUNT).
*
* Return: 0 if request was submitted successfully, -ve on error
*/
static int aux_request(struct udevice *dev, struct aux_transaction *request)
{
u32 defer_count = 0;
u32 timeout_count = 0;
while ((defer_count < AUX_MAX_DEFER_COUNT) &&
(timeout_count < AUX_MAX_TIMEOUT_COUNT)) {
int status = aux_wait_ready(dev);
if (status) {
/* The RX device isn't ready yet. */
timeout_count++;
continue;
}
status = aux_request_send(dev, request);
if (status == -EAGAIN) {
/* The request was deferred. */
defer_count++;
} else if (status == -ETIMEDOUT) {
/* Waiting for a reply timed out. */
timeout_count++;
} else {
/*
* -EIO indicates that the request was NACK'ed,
* 0 indicates that the request was ACK'ed.
*/
return status;
}
udelay(100);
}
/* The request was not successfully received by the RX device. */
return -ETIMEDOUT;
}
/**
* aux_common() - Common (read/write) AUX communication transmission
* @dev: The LogiCore DP TX device in question
* @cmd_type: Command code of the transaction
* @address: The DPCD address of the transaction
* @num_bytes: Number of bytes in the payload data
* @data: The payload data of the AUX command
*
* Common sequence of submitting an AUX command for AUX read, AUX write,
* I2C-over-AUX read, and I2C-over-AUX write transactions. If required, the
* reads and writes are split into multiple requests, each acting on a maximum
* of 16 bytes.
*
* Return: 0 if OK, -ve on error
*/
static int aux_common(struct udevice *dev, u32 cmd_type, u32 address,
u32 num_bytes, u8 *data)
{
struct aux_transaction request;
u32 bytes_left;
/*
* Set the start address for AUX transactions. For I2C transactions,
* this is the address of the I2C bus.
*/
request.address = address;
bytes_left = num_bytes;
while (bytes_left) {
int status;
request.cmd_code = cmd_type;
if (cmd_type == AUX_CMD_READ ||
cmd_type == AUX_CMD_WRITE) {
/* Increment address for normal AUX transactions. */
request.address = address + (num_bytes - bytes_left);
}
/* Increment the pointer to the supplied data buffer. */
request.data = &data[num_bytes - bytes_left];
request.num_bytes = (bytes_left > 16) ? 16 : bytes_left;
bytes_left -= request.num_bytes;
if (cmd_type == AUX_CMD_I2C_READ && bytes_left) {
/*
* Middle of a transaction I2C read request. Override
* the command code that was set to cmd_type.
*/
request.cmd_code = AUX_CMD_I2C_READ_MOT;
} else if ((cmd_type == AUX_CMD_I2C_WRITE) && bytes_left) {
/*
* Middle of a transaction I2C write request. Override
* the command code that was set to cmd_type.
*/
request.cmd_code = AUX_CMD_I2C_WRITE_MOT;
}
status = aux_request(dev, &request);
if (status)
return status;
}
return 0;
}
/**
* aux_read() - Issue AUX read request
* @dev: The LogiCore DP TX device in question
* @dpcd_address: The DPCD address to read from
* @bytes_to_read: Number of bytes to read
* @read_data: Buffer to receive the read data
*
* Issue a read request over the AUX channel that will read from the RX
* device's DisplayPort Configuration data (DPCD) address space. The read
* message will be divided into multiple transactions which read a maximum of
* 16 bytes each.
*
* Return: 0 if read operation was successful, -ve on error
*/
static int aux_read(struct udevice *dev, u32 dpcd_address, u32 bytes_to_read,
void *read_data)
{
int status;
if (!is_connected(dev))
return -ENODEV;
/* Send AUX read transaction. */
status = aux_common(dev, AUX_CMD_READ, dpcd_address,
bytes_to_read, (u8 *)read_data);
return status;
}
/**
* aux_write() - Issue AUX write request
* @dev: The LogiCore DP TX device in question
* @dpcd_address: The DPCD address to write to
* @bytes_to_write: Number of bytes to write
* @write_data: Buffer containig data to be written
*
* Issue a write request over the AUX channel that will write to
* the RX device's DisplayPort Configuration data (DPCD) address space. The
* write message will be divided into multiple transactions which write a
* maximum of 16 bytes each.
*
* Return: 0 if write operation was successful, -ve on error
*/
static int aux_write(struct udevice *dev, u32 dpcd_address, u32 bytes_to_write,
void *write_data)
{
int status;
if (!is_connected(dev))
return -ENODEV;
/* Send AUX write transaction. */
status = aux_common(dev, AUX_CMD_WRITE, dpcd_address,
bytes_to_write, (u8 *)write_data);
return status;
}
/* Core initialization */
/**
* initialize() - Initialize a LogiCore DP TX device
* @dev: The LogiCore DP TX device in question
*
* Return: Always 0
*/
static int initialize(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u32 val;
u32 phy_config;
unsigned int k;
/* place the PHY (and GTTXRESET) into reset. */
phy_config = get_reg(dev, REG_PHY_CONFIG);
set_reg(dev, REG_PHY_CONFIG, phy_config | PHY_CONFIG_GT_ALL_RESET_MASK);
/* reset the video streams and AUX logic. */
set_reg(dev, REG_SOFT_RESET,
SOFT_RESET_VIDEO_STREAM_ALL_MASK |
SOFT_RESET_AUX_MASK);
/* disable the DisplayPort TX core. */
set_reg(dev, REG_ENABLE, 0);
/* set the clock divider. */
val = get_reg(dev, REG_AUX_CLK_DIVIDER);
val &= ~AUX_CLK_DIVIDER_VAL_MASK;
val |= dp_tx->s_axi_clk / 1000000;
set_reg(dev, REG_AUX_CLK_DIVIDER, val);
/* set the DisplayPort TX core's clock speed. */
set_reg(dev, REG_PHY_CLOCK_SELECT, PHY_CLOCK_SELECT_DEFAULT);
/* bring the PHY (and GTTXRESET) out of reset. */
set_reg(dev, REG_PHY_CONFIG,
phy_config & ~PHY_CONFIG_GT_ALL_RESET_MASK);
/* enable the DisplayPort TX core. */
set_reg(dev, REG_ENABLE, 1);
/* Unmask Hot-Plug-Detect (HPD) interrupts. */
set_reg(dev, REG_INTERRUPT_MASK,
~INTERRUPT_MASK_HPD_PULSE_DETECTED_MASK &
~INTERRUPT_MASK_HPD_EVENT_MASK &
~INTERRUPT_MASK_HPD_IRQ_MASK);
for (k = 0; k < 4; k++) {
/* Disable pre-cursor levels. */
set_reg(dev, REG_PHY_PRECURSOR_LANE_0 + 4 * k, 0);
/* Write default voltage swing levels to the TX registers. */
set_reg(dev, REG_PHY_VOLTAGE_DIFF_LANE_0 + 4 * k, 0);
/* Write default pre-emphasis levels to the TX registers. */
set_reg(dev, REG_PHY_POSTCURSOR_LANE_0 + 4 * k, 0);
}
return 0;
}
/**
* is_link_rate_valid() - Check if given link rate is valif for device
* @dev: The LogiCore DP TX device in question
* @link_rate: The link rate to be checked for validity
*
* Return: true if he supplied link rate is valid, false otherwise
*/
static bool is_link_rate_valid(struct udevice *dev, u8 link_rate)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
bool valid = true;
if (link_rate != LINK_BW_SET_162GBPS &&
link_rate != LINK_BW_SET_270GBPS &&
link_rate != LINK_BW_SET_540GBPS)
valid = false;
else if (link_rate > dp_tx->link_config.max_link_rate)
valid = false;
return valid;
}
/**
* is_lane_count_valid() - Check if given lane count is valif for device
* @dev: The LogiCore DP TX device in question
* @lane_count: The lane count to be checked for validity
*
* Return: true if he supplied lane count is valid, false otherwise
*/
static bool is_lane_count_valid(struct udevice *dev, u8 lane_count)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
bool valid = true;
if (lane_count != LANE_COUNT_SET_1 &&
lane_count != LANE_COUNT_SET_2 &&
lane_count != LANE_COUNT_SET_4)
valid = false;
else if (lane_count > dp_tx->link_config.max_lane_count)
valid = false;
return valid;
}
/**
* get_rx_capabilities() - Check if capabilities of RX device are valid for TX
* device
* @dev: The LogiCore DP TX device in question
*
* Return: 0 if the capabilities of the RX device are valid for the TX device,
* -ve if not, of an error occurred during capability determination
*/
static int get_rx_capabilities(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u8 rx_max_link_rate;
u8 rx_max_lane_count;
if (!is_connected(dev))
return -ENODEV;
status = aux_read(dev, DPCD_RECEIVER_CAP_FIELD_START, 16,
dp_tx->dpcd_rx_caps);
if (status)
return -EIO;
rx_max_link_rate = dp_tx->dpcd_rx_caps[DPCD_MAX_LINK_RATE];
rx_max_lane_count = dp_tx->dpcd_rx_caps[DPCD_MAX_LANE_COUNT] &
DPCD_MAX_LANE_COUNT_MASK;
dp_tx->link_config.max_link_rate =
(rx_max_link_rate > dp_tx->max_link_rate) ?
dp_tx->max_link_rate : rx_max_link_rate;
if (!is_link_rate_valid(dev, rx_max_link_rate))
return -EINVAL;
dp_tx->link_config.max_lane_count =
(rx_max_lane_count > dp_tx->max_lane_count) ?
dp_tx->max_lane_count : rx_max_lane_count;
if (!is_lane_count_valid(dev, rx_max_lane_count))
return -EINVAL;
dp_tx->link_config.support_enhanced_framing_mode =
dp_tx->dpcd_rx_caps[DPCD_MAX_LANE_COUNT] &
DPCD_ENHANCED_FRAME_SUPPORT_MASK;
return 0;
}
/**
* enable_main_link() - Switch on main link for a device
* @dev: The LogiCore DP TX device in question
*/
static void enable_main_link(struct udevice *dev)
{
/* reset the scrambler. */
set_reg(dev, REG_FORCE_SCRAMBLER_RESET, 0x1);
/* enable the main stream. */
set_reg(dev, REG_ENABLE_MAIN_STREAM, 0x1);
}
/**
* disable_main_link() - Switch off main link for a device
* @dev: The LogiCore DP TX device in question
*/
static void disable_main_link(struct udevice *dev)
{
/* reset the scrambler. */
set_reg(dev, REG_FORCE_SCRAMBLER_RESET, 0x1);
/* Disable the main stream. */
set_reg(dev, REG_ENABLE_MAIN_STREAM, 0x0);
}
/**
* reset_dp_phy() - Reset a device
* @dev: The LogiCore DP TX device in question
* @reset: Bit mask determining which bits in the device's config register
* should be set for the reset
*/
static void reset_dp_phy(struct udevice *dev, u32 reset)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u32 val;
set_reg(dev, REG_ENABLE, 0x0);
val = get_reg(dev, REG_PHY_CONFIG);
/* Apply reset. */
set_reg(dev, REG_PHY_CONFIG, val | reset);
/* Remove reset. */
set_reg(dev, REG_PHY_CONFIG, val);
/* Wait for the PHY to be ready. */
wait_phy_ready(dev, phy_status_lanes_ready_mask(dp_tx->max_lane_count));
set_reg(dev, REG_ENABLE, 0x1);
}
/**
* set_enhanced_frame_mode() - Enable/Disable enhanced frame mode
* @dev: The LogiCore DP TX device in question
* @enable: Flag to determine whether to enable (1) or disable (0) the enhanced
* frame mode
*
* Enable or disable the enhanced framing symbol sequence for
* both the DisplayPort TX core and the RX device.
*
* Return: 0 if enabling/disabling the enhanced frame mode was successful, -ve
* on error
*/
static int set_enhanced_frame_mode(struct udevice *dev, u8 enable)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u8 val;
if (!is_connected(dev))
return -ENODEV;
if (dp_tx->link_config.support_enhanced_framing_mode)
dp_tx->link_config.enhanced_framing_mode = enable;
else
dp_tx->link_config.enhanced_framing_mode = false;
/* Write enhanced frame mode enable to the DisplayPort TX core. */
set_reg(dev, REG_ENHANCED_FRAME_EN,
dp_tx->link_config.enhanced_framing_mode);
/* Write enhanced frame mode enable to the RX device. */
status = aux_read(dev, DPCD_LANE_COUNT_SET, 0x1, &val);
if (status)
return -EIO;
if (dp_tx->link_config.enhanced_framing_mode)
val |= DPCD_ENHANCED_FRAME_EN_MASK;
else
val &= ~DPCD_ENHANCED_FRAME_EN_MASK;
status = aux_write(dev, DPCD_LANE_COUNT_SET, 0x1, &val);
if (status)
return -EIO;
return 0;
}
/**
* set_lane_count() - Set the lane count
* @dev: The LogiCore DP TX device in question
* @lane_count: Lane count to set
*
* Set the number of lanes to be used by the main link for both
* the DisplayPort TX core and the RX device.
*
* Return: 0 if setting the lane count was successful, -ve on error
*/
static int set_lane_count(struct udevice *dev, u8 lane_count)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u8 val;
if (!is_connected(dev))
return -ENODEV;
printf(" set lane count to %u\n", lane_count);
dp_tx->link_config.lane_count = lane_count;
/* Write the new lane count to the DisplayPort TX core. */
set_reg(dev, REG_LANE_COUNT_SET, dp_tx->link_config.lane_count);
/* Write the new lane count to the RX device. */
status = aux_read(dev, DPCD_LANE_COUNT_SET, 0x1, &val);
if (status)
return -EIO;
val &= ~DPCD_LANE_COUNT_SET_MASK;
val |= dp_tx->link_config.lane_count;
status = aux_write(dev, DPCD_LANE_COUNT_SET, 0x1, &val);
if (status)
return -EIO;
return 0;
}
/**
* set_clk_speed() - Set DP phy clock speed
* @dev: The LogiCore DP TX device in question
* @speed: The clock frquency to set (one of PHY_CLOCK_SELECT_*)
*
* Set the clock frequency for the DisplayPort PHY corresponding to a desired
* data rate.
*
* Return: 0 if setting the DP phy clock speed was successful, -ve on error
*/
static int set_clk_speed(struct udevice *dev, u32 speed)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u32 val;
u32 mask;
/* Disable the DisplayPort TX core first. */
val = get_reg(dev, REG_ENABLE);
set_reg(dev, REG_ENABLE, 0x0);
/* Change speed of the feedback clock. */
set_reg(dev, REG_PHY_CLOCK_SELECT, speed);
/* Re-enable the DisplayPort TX core if it was previously enabled. */
if (val)
set_reg(dev, REG_ENABLE, 0x1);
/* Wait until the PHY is ready. */
mask = phy_status_lanes_ready_mask(dp_tx->max_lane_count);
status = wait_phy_ready(dev, mask);
if (status)
return -EIO;
return 0;
}
/**
* set_link_rate() - Set the link rate
* @dev: The LogiCore DP TX device in question
* @link_rate: The link rate to set (one of LINK_BW_SET_*)
*
* Set the data rate to be used by the main link for both the DisplayPort TX
* core and the RX device.
*
* Return: 0 if setting the link rate was successful, -ve on error
*/
static int set_link_rate(struct udevice *dev, u8 link_rate)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
/* Write a corresponding clock frequency to the DisplayPort TX core. */
switch (link_rate) {
case LINK_BW_SET_162GBPS:
printf(" set link rate to 1.62 Gb/s\n");
status = set_clk_speed(dev, PHY_CLOCK_SELECT_162GBPS);
break;
case LINK_BW_SET_270GBPS:
printf(" set link rate to 2.70 Gb/s\n");
status = set_clk_speed(dev, PHY_CLOCK_SELECT_270GBPS);
break;
case LINK_BW_SET_540GBPS:
printf(" set link rate to 5.40 Gb/s\n");
status = set_clk_speed(dev, PHY_CLOCK_SELECT_540GBPS);
break;
default:
return -EINVAL;
}
if (status)
return -EIO;
dp_tx->link_config.link_rate = link_rate;
/* Write new link rate to the DisplayPort TX core. */
set_reg(dev, REG_LINK_BW_SET, dp_tx->link_config.link_rate);
/* Write new link rate to the RX device. */
status = aux_write(dev, DPCD_LINK_BW_SET, 1,
&dp_tx->link_config.link_rate);
if (status)
return -EIO;
return 0;
}
/* Link training */
/**
* get_training_delay() - Get training delay
* @dev: The LogiCore DP TX device in question
* @training_state: The training state for which the required training delay
* should be queried
*
* Determine what the RX device's required training delay is for
* link training.
*
* Return: The training delay in us
*/
static int get_training_delay(struct udevice *dev, int training_state)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u16 delay;
switch (dp_tx->dpcd_rx_caps[DPCD_TRAIN_AUX_RD_INTERVAL]) {
case DPCD_TRAIN_AUX_RD_INT_100_400US:
if (training_state == TS_CLOCK_RECOVERY)
/* delay for the clock recovery phase. */
delay = 100;
else
/* delay for the channel equalization phase. */
delay = 400;
break;
case DPCD_TRAIN_AUX_RD_INT_4MS:
delay = 4000;
break;
case DPCD_TRAIN_AUX_RD_INT_8MS:
delay = 8000;
break;
case DPCD_TRAIN_AUX_RD_INT_12MS:
delay = 12000;
break;
case DPCD_TRAIN_AUX_RD_INT_16MS:
delay = 16000;
break;
default:
/* Default to 20 ms. */
delay = 20000;
break;
}
return delay;
}
/**
* set_vswing_preemp() - Build AUX data to set voltage swing and pre-emphasis
* @dev: The LogiCore DP TX device in question
* @aux_data: Buffer to receive the built AUX data
*
* Build AUX data to set current voltage swing and pre-emphasis level settings;
* the necessary data is taken from the link_config structure.
*/
static void set_vswing_preemp(struct udevice *dev, u8 *aux_data)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u8 data;
u8 vs_level_rx = dp_tx->link_config.vs_level;
u8 pe_level_rx = dp_tx->link_config.pe_level;
/* Set up the data buffer for writing to the RX device. */
data = (pe_level_rx << DPCD_TRAINING_LANEX_SET_PE_SHIFT) | vs_level_rx;
/* The maximum voltage swing has been reached. */
if (vs_level_rx == MAXIMUM_VS_LEVEL)
data |= DPCD_TRAINING_LANEX_SET_MAX_VS_MASK;
/* The maximum pre-emphasis level has been reached. */
if (pe_level_rx == MAXIMUM_PE_LEVEL)
data |= DPCD_TRAINING_LANEX_SET_MAX_PE_MASK;
memset(aux_data, data, 4);
}
/**
* adj_vswing_preemp() - Adjust voltage swing and pre-emphasis
* @dev: The LogiCore DP TX device in question
*
* Set new voltage swing and pre-emphasis levels using the
* adjustment requests obtained from the RX device.
*
* Return: 0 if voltage swing and pre-emphasis could be adjusted successfully,
* -ve on error
*/
static int adj_vswing_preemp(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u8 index;
u8 vs_level_adj_req[4];
u8 pe_level_adj_req[4];
u8 aux_data[4];
u8 *ajd_reqs = &dp_tx->lane_status_ajd_reqs[4];
/*
* Analyze the adjustment requests for changes in voltage swing and
* pre-emphasis levels.
*/
vs_level_adj_req[0] = ajd_reqs[0] & DPCD_ADJ_REQ_LANE_0_2_VS_MASK;
vs_level_adj_req[1] = (ajd_reqs[0] & DPCD_ADJ_REQ_LANE_1_3_VS_MASK) >>
DPCD_ADJ_REQ_LANE_1_3_VS_SHIFT;
vs_level_adj_req[2] = ajd_reqs[1] & DPCD_ADJ_REQ_LANE_0_2_VS_MASK;
vs_level_adj_req[3] = (ajd_reqs[1] & DPCD_ADJ_REQ_LANE_1_3_VS_MASK) >>
DPCD_ADJ_REQ_LANE_1_3_VS_SHIFT;
pe_level_adj_req[0] = (ajd_reqs[0] & DPCD_ADJ_REQ_LANE_0_2_PE_MASK) >>
DPCD_ADJ_REQ_LANE_0_2_PE_SHIFT;
pe_level_adj_req[1] = (ajd_reqs[0] & DPCD_ADJ_REQ_LANE_1_3_PE_MASK) >>
DPCD_ADJ_REQ_LANE_1_3_PE_SHIFT;
pe_level_adj_req[2] = (ajd_reqs[1] & DPCD_ADJ_REQ_LANE_0_2_PE_MASK) >>
DPCD_ADJ_REQ_LANE_0_2_PE_SHIFT;
pe_level_adj_req[3] = (ajd_reqs[1] & DPCD_ADJ_REQ_LANE_1_3_PE_MASK) >>
DPCD_ADJ_REQ_LANE_1_3_PE_SHIFT;
/*
* Change the drive settings to match the adjustment requests. Use the
* greatest level requested.
*/
dp_tx->link_config.vs_level = 0;
dp_tx->link_config.pe_level = 0;
for (index = 0; index < dp_tx->link_config.lane_count; index++) {
if (vs_level_adj_req[index] > dp_tx->link_config.vs_level)
dp_tx->link_config.vs_level = vs_level_adj_req[index];
if (pe_level_adj_req[index] > dp_tx->link_config.pe_level)
dp_tx->link_config.pe_level = pe_level_adj_req[index];
}
/*
* Verify that the voltage swing and pre-emphasis combination is
* allowed. Some combinations will result in a differential peak-to-peak
* voltage that is outside the permissible range. See the VESA
* DisplayPort v1.2 Specification, section 3.1.5.2.
* The valid combinations are:
* PE=0 PE=1 PE=2 PE=3
* VS=0 valid valid valid valid
* VS=1 valid valid valid
* VS=2 valid valid
* VS=3 valid
*
* NOTE:
* Xilinix dp_v3_1 driver seems to have an off by one error when
* limiting pe_level which is fixed here.
*/
if (dp_tx->link_config.pe_level > (3 - dp_tx->link_config.vs_level))
dp_tx->link_config.pe_level = 3 - dp_tx->link_config.vs_level;
/*
* Make the adjustments to both the DisplayPort TX core and the RX
* device.
*/
set_vswing_preemp(dev, aux_data);
/*
* Write the voltage swing and pre-emphasis levels for each lane to the
* RX device.
*/
status = aux_write(dev, DPCD_TRAINING_LANE0_SET, 4, aux_data);
if (status)
return -EIO;
return 0;
}
/**
* get_lane_status_adj_reqs() - Read lane status and adjustment requests
* information from the device
* @dev: The LogiCore DP TX device in question
*
* Do a burst AUX read from the RX device over the AUX channel. The contents of
* the status registers will be stored for later use by check_clock_recovery,
* check_channel_equalization, and adj_vswing_preemp.
*
* Return: 0 if the status information were read successfully, -ve on error
*/
static int get_lane_status_adj_reqs(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
/*
* Read and store 4 bytes of lane status and 2 bytes of adjustment
* requests.
*/
status = aux_read(dev, DPCD_STATUS_LANE_0_1, 6,
dp_tx->lane_status_ajd_reqs);
if (status)
return -EIO;
return 0;
}
/**
* check_clock_recovery() - Check clock recovery success
* @dev: The LogiCore DP TX device in question
* @lane_count: The number of lanes for which to check clock recovery success
*
* Check if the RX device's DisplayPort Configuration data (DPCD) indicates
* that the clock recovery sequence during link training was successful - the
* RX device's link clock and data recovery unit has realized and maintained
* the frequency lock for all lanes currently in use.
*
* Return: 0 if clock recovery was successful on all lanes in question, -ve if
* not
*/
static int check_clock_recovery(struct udevice *dev, u8 lane_count)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u8 *lane_status = dp_tx->lane_status_ajd_reqs;
/* Check that all LANEx_CR_DONE bits are set. */
switch (lane_count) {
case LANE_COUNT_SET_4:
if (!(lane_status[1] & DPCD_STATUS_LANE_3_CR_DONE_MASK))
goto out_fail;
if (!(lane_status[1] & DPCD_STATUS_LANE_2_CR_DONE_MASK))
goto out_fail;
/* Drop through and check lane 1. */
case LANE_COUNT_SET_2:
if (!(lane_status[0] & DPCD_STATUS_LANE_1_CR_DONE_MASK))
goto out_fail;
/* Drop through and check lane 0. */
case LANE_COUNT_SET_1:
if (!(lane_status[0] & DPCD_STATUS_LANE_0_CR_DONE_MASK))
goto out_fail;
default:
/* All (lane_count) lanes have achieved clock recovery. */
break;
}
return 0;
out_fail:
return -EIO;
}
/**
* check_channel_equalization() - Check channel equalization success
* @dev: The LogiCore DP TX device in question
* @lane_count: The number of lanes for which to check channel equalization
* success
*
* Check if the RX device's DisplayPort Configuration data (DPCD) indicates
* that the channel equalization sequence during link training was successful -
* the RX device has achieved channel equalization, symbol lock, and interlane
* alignment for all lanes currently in use.
*
* Return: 0 if channel equalization was successful on all lanes in question,
* -ve if not
*/
static int check_channel_equalization(struct udevice *dev, u8 lane_count)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u8 *lane_status = dp_tx->lane_status_ajd_reqs;
/* Check that all LANEx_CHANNEL_EQ_DONE bits are set. */
switch (lane_count) {
case LANE_COUNT_SET_4:
if (!(lane_status[1] & DPCD_STATUS_LANE_3_CE_DONE_MASK))
goto out_fail;
if (!(lane_status[1] & DPCD_STATUS_LANE_2_CE_DONE_MASK))
goto out_fail;
/* Drop through and check lane 1. */
case LANE_COUNT_SET_2:
if (!(lane_status[0] & DPCD_STATUS_LANE_1_CE_DONE_MASK))
goto out_fail;
/* Drop through and check lane 0. */
case LANE_COUNT_SET_1:
if (!(lane_status[0] & DPCD_STATUS_LANE_0_CE_DONE_MASK))
goto out_fail;
default:
/* All (lane_count) lanes have achieved channel equalization. */
break;
}
/* Check that all LANEx_SYMBOL_LOCKED bits are set. */
switch (lane_count) {
case LANE_COUNT_SET_4:
if (!(lane_status[1] & DPCD_STATUS_LANE_3_SL_DONE_MASK))
goto out_fail;
if (!(lane_status[1] & DPCD_STATUS_LANE_2_SL_DONE_MASK))
goto out_fail;
/* Drop through and check lane 1. */
case LANE_COUNT_SET_2:
if (!(lane_status[0] & DPCD_STATUS_LANE_1_SL_DONE_MASK))
goto out_fail;
/* Drop through and check lane 0. */
case LANE_COUNT_SET_1:
if (!(lane_status[0] & DPCD_STATUS_LANE_0_SL_DONE_MASK))
goto out_fail;
default:
/* All (lane_count) lanes have achieved symbol lock. */
break;
}
/* Check that interlane alignment is done. */
if (!(lane_status[2] & DPCD_LANE_ALIGN_STATUS_UPDATED_IA_DONE_MASK))
goto out_fail;
return 0;
out_fail:
return -EIO;
}
/**
* set_training_pattern() - Set training pattern for link training
* @dev: The LogiCore DP TX device in question
* @pattern: The training pattern to set
*
* Set the training pattern to be used during link training for both the
* DisplayPort TX core and the RX device.
*
* Return: 0 if the training pattern could be set successfully, -ve if not
*/
static int set_training_pattern(struct udevice *dev, u32 pattern)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u8 aux_data[5];
/* Write to the DisplayPort TX core. */
set_reg(dev, REG_TRAINING_PATTERN_SET, pattern);
aux_data[0] = pattern;
/* Write scrambler disable to the DisplayPort TX core. */
switch (pattern) {
case TRAINING_PATTERN_SET_OFF:
set_reg(dev, REG_SCRAMBLING_DISABLE, 0);
dp_tx->link_config.scrambler_en = 1;
break;
case TRAINING_PATTERN_SET_TP1:
case TRAINING_PATTERN_SET_TP2:
case TRAINING_PATTERN_SET_TP3:
aux_data[0] |= DPCD_TP_SET_SCRAMB_DIS_MASK;
set_reg(dev, REG_SCRAMBLING_DISABLE, 1);
dp_tx->link_config.scrambler_en = 0;
break;
default:
break;
}
/*
* Make the adjustments to both the DisplayPort TX core and the RX
* device.
*/
set_vswing_preemp(dev, &aux_data[1]);
/*
* Write the voltage swing and pre-emphasis levels for each lane to the
* RX device.
*/
if (pattern == TRAINING_PATTERN_SET_OFF)
status = aux_write(dev, DPCD_TP_SET, 1, aux_data);
else
status = aux_write(dev, DPCD_TP_SET, 5, aux_data);
if (status)
return -EIO;
return 0;
}
/**
* training_state_clock_recovery() - Run clock recovery part of link training
* @dev: The LogiCore DP TX device in question
*
* Run the clock recovery sequence as part of link training. The
* sequence is as follows:
*
* 0) Start signaling at the minimum voltage swing, pre-emphasis, and
* post- cursor levels.
* 1) Transmit training pattern 1 over the main link with symbol
* scrambling disabled.
* 2) The clock recovery loop. If clock recovery is unsuccessful after
* MaxIterations loop iterations, return.
* 2a) Wait for at least the period of time specified in the RX device's
* DisplayPort Configuration data (DPCD) register,
* TRAINING_AUX_RD_INTERVAL.
* 2b) Check if all lanes have achieved clock recovery lock. If so,
* return.
* 2c) Check if the same voltage swing level has been used 5 consecutive
* times or if the maximum level has been reached. If so, return.
* 2d) Adjust the voltage swing, pre-emphasis, and post-cursor levels as
* requested by the RX device.
* 2e) Loop back to 2a.
*
* For a more detailed description of the clock recovery sequence, see section
* 3.5.1.2.1 of the DisplayPort 1.2a specification document.
*
* Return: The next state machine state to advance to
*/
static unsigned int training_state_clock_recovery(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u32 delay_us;
u8 prev_vs_level = 0;
u8 same_vs_level_count = 0;
/*
* Obtain the required delay for clock recovery as specified by the
* RX device.
*/
delay_us = get_training_delay(dev, TS_CLOCK_RECOVERY);
/* Start CRLock. */
/* Transmit training pattern 1. */
/* Disable the scrambler. */
/* Start from minimal voltage swing and pre-emphasis levels. */
dp_tx->link_config.vs_level = 0;
dp_tx->link_config.pe_level = 0;
status = set_training_pattern(dev, TRAINING_PATTERN_SET_TP1);
if (status)
return TS_FAILURE;
while (1) {
/* Wait delay specified in TRAINING_AUX_RD_INTERVAL. */
udelay(delay_us);
/* Get lane and adjustment requests. */
status = get_lane_status_adj_reqs(dev);
if (status)
return TS_FAILURE;
/*
* Check if all lanes have realized and maintained the frequency
* lock and get adjustment requests.
*/
status = check_clock_recovery(dev,
dp_tx->link_config.lane_count);
if (!status)
return TS_CHANNEL_EQUALIZATION;
/*
* Check if the same voltage swing for each lane has been used 5
* consecutive times.
*/
if (prev_vs_level == dp_tx->link_config.vs_level) {
same_vs_level_count++;
} else {
same_vs_level_count = 0;
prev_vs_level = dp_tx->link_config.vs_level;
}
if (same_vs_level_count >= 5)
break;
/* Only try maximum voltage swing once. */
if (dp_tx->link_config.vs_level == MAXIMUM_VS_LEVEL)
break;
/* Adjust the drive settings as requested by the RX device. */
status = adj_vswing_preemp(dev);
if (status)
/* The AUX write failed. */
return TS_FAILURE;
}
return TS_ADJUST_LINK_RATE;
}
/**
* training_state_channel_equalization() - Run channel equalization part of
* link training
* @dev: The LogiCore DP TX device in question
*
* Run the channel equalization sequence as part of link
* training. The sequence is as follows:
*
* 0) Start signaling with the same drive settings used at the end of the
* clock recovery sequence.
* 1) Transmit training pattern 2 (or 3) over the main link with symbol
* scrambling disabled.
* 2) The channel equalization loop. If channel equalization is
* unsuccessful after 5 loop iterations, return.
* 2a) Wait for at least the period of time specified in the RX device's
* DisplayPort Configuration data (DPCD) register,
* TRAINING_AUX_RD_INTERVAL.
* 2b) Check if all lanes have achieved channel equalization, symbol lock,
* and interlane alignment. If so, return.
* 2c) Check if the same voltage swing level has been used 5 consecutive
* times or if the maximum level has been reached. If so, return.
* 2d) Adjust the voltage swing, pre-emphasis, and post-cursor levels as
* requested by the RX device.
* 2e) Loop back to 2a.
*
* For a more detailed description of the channel equalization sequence, see
* section 3.5.1.2.2 of the DisplayPort 1.2a specification document.
*
* Return: The next state machine state to advance to
*/
static int training_state_channel_equalization(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
u32 delay_us;
u32 iteration_count = 0;
/*
* Obtain the required delay for channel equalization as specified by
* the RX device.
*/
delay_us = get_training_delay(dev, TS_CHANNEL_EQUALIZATION);
/* Start channel equalization. */
/* Write the current drive settings. */
/* Transmit training pattern 2/3. */
if (dp_tx->dpcd_rx_caps[DPCD_MAX_LANE_COUNT] & DPCD_TPS3_SUPPORT_MASK)
status = set_training_pattern(dev, TRAINING_PATTERN_SET_TP3);
else
status = set_training_pattern(dev, TRAINING_PATTERN_SET_TP2);
if (status)
return TS_FAILURE;
while (iteration_count < 5) {
/* Wait delay specified in TRAINING_AUX_RD_INTERVAL. */
udelay(delay_us);
/* Get lane and adjustment requests. */
status = get_lane_status_adj_reqs(dev);
if (status)
/* The AUX read failed. */
return TS_FAILURE;
/* Check that all lanes still have their clocks locked. */
status = check_clock_recovery(dev,
dp_tx->link_config.lane_count);
if (status)
break;
/*
* Check if all lanes have accomplished channel equalization,
* symbol lock, and interlane alignment.
*/
status =
check_channel_equalization(dev,
dp_tx->link_config.lane_count);
if (!status)
return TS_SUCCESS;
/* Adjust the drive settings as requested by the RX device. */
status = adj_vswing_preemp(dev);
if (status)
/* The AUX write failed. */
return TS_FAILURE;
iteration_count++;
}
/*
* Tried 5 times with no success. Try a reduced bitrate first, then
* reduce the number of lanes.
*/
return TS_ADJUST_LINK_RATE;
}
/**
* training_state_adjust_link_rate() - Downshift data rate and/or lane count
* @dev: The LogiCore DP TX device in question
*
* This function is reached if either the clock recovery or the channel
* equalization process failed during training. As a result, the data rate will
* be downshifted, and training will be re-attempted (starting with clock
* recovery) at the reduced data rate. If the data rate is already at 1.62
* Gbps, a downshift in lane count will be attempted.
*
* Return: The next state machine state to advance to
*/
static int training_state_adjust_link_rate(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
switch (dp_tx->link_config.link_rate) {
case LINK_BW_SET_540GBPS:
status = set_link_rate(dev, LINK_BW_SET_270GBPS);
if (status) {
status = TS_FAILURE;
break;
}
status = TS_CLOCK_RECOVERY;
break;
case LINK_BW_SET_270GBPS:
status = set_link_rate(dev, LINK_BW_SET_162GBPS);
if (status) {
status = TS_FAILURE;
break;
}
status = TS_CLOCK_RECOVERY;
break;
default:
/*
* Already at the lowest link rate. Try reducing the lane
* count next.
*/
status = TS_ADJUST_LANE_COUNT;
break;
}
return status;
}
/**
* trainig_state_adjust_lane_count - Downshift lane count
* @dev: The LogiCore DP TX device in question
*
* This function is reached if either the clock recovery or the channel
* equalization process failed during training, and a minimal data rate of 1.62
* Gbps was being used. As a result, the number of lanes in use will be
* reduced, and training will be re-attempted (starting with clock recovery) at
* this lower lane count.
*
* Return: The next state machine state to advance to
*/
static int trainig_state_adjust_lane_count(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
switch (dp_tx->link_config.lane_count) {
case LANE_COUNT_SET_4:
status = set_lane_count(dev, LANE_COUNT_SET_2);
if (status) {
status = TS_FAILURE;
break;
}
status = set_link_rate(dev, dp_tx->link_config.max_link_rate);
if (status) {
status = TS_FAILURE;
break;
}
status = TS_CLOCK_RECOVERY;
break;
case LANE_COUNT_SET_2:
status = set_lane_count(dev, LANE_COUNT_SET_1);
if (status) {
status = TS_FAILURE;
break;
}
status = set_link_rate(dev, dp_tx->link_config.max_link_rate);
if (status) {
status = TS_FAILURE;
break;
}
status = TS_CLOCK_RECOVERY;
break;
default:
/*
* Already at the lowest lane count. Training has failed at the
* lowest lane count and link rate.
*/
status = TS_FAILURE;
break;
}
return status;
}
/**
* check_link_status() - Check status of link
* @dev: The LogiCore DP TX device in question
* @lane_count: The lane count to use for the check
*
* Check if the receiver's DisplayPort Configuration data (DPCD) indicates the
* receiver has achieved and maintained clock recovery, channel equalization,
* symbol lock, and interlane alignment for all lanes currently in use.
*
* Return: 0 if the link status is OK, -ve if a error occurred during checking
*/
static int check_link_status(struct udevice *dev, u8 lane_count)
{
u8 retry_count = 0;
if (!is_connected(dev))
return -ENODEV;
/* Retrieve AUX info. */
do {
int status;
/* Get lane and adjustment requests. */
status = get_lane_status_adj_reqs(dev);
if (status)
return -EIO;
/* Check if the link needs training. */
if ((check_clock_recovery(dev, lane_count) == 0) &&
(check_channel_equalization(dev, lane_count) == 0))
return 0;
retry_count++;
} while (retry_count < 5); /* Retry up to 5 times. */
return -EIO;
}
/**
* run_training() - Run link training
* @dev: The LogiCore DP TX device in question
*
* Run the link training process. It is implemented as a state machine, with
* each state returning the next state. First, the clock recovery sequence will
* be run; if successful, the channel equalization sequence will run. If either
* the clock recovery or channel equalization sequence failed, the link rate or
* the number of lanes used will be reduced and training will be re-attempted.
* If training fails at the minimal data rate, 1.62 Gbps with a single lane,
* training will no longer re-attempt and fail.
*
* ### Here be dragons ###
* There are undocumented timeout constraints in the link training process. In
* DP v1.2a spec, Chapter 3.5.1.2.2 a 10ms limit for the complete training
* process is mentioned. Which individual timeouts are derived and implemented
* by sink manufacturers is unknown. So each step should be as short as
* possible and link training should start as soon as possible after HPD.
*
* Return: 0 if the training sequence ran successfully, -ve if a error occurred
* or the training failed
*/
static int run_training(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
int training_state = TS_CLOCK_RECOVERY;
while (1) {
switch (training_state) {
case TS_CLOCK_RECOVERY:
training_state =
training_state_clock_recovery(dev);
break;
case TS_CHANNEL_EQUALIZATION:
training_state =
training_state_channel_equalization(dev);
break;
case TS_ADJUST_LINK_RATE:
training_state =
training_state_adjust_link_rate(dev);
break;
case TS_ADJUST_LANE_COUNT:
training_state =
trainig_state_adjust_lane_count(dev);
break;
default:
break;
}
if (training_state == TS_SUCCESS)
break;
else if (training_state == TS_FAILURE)
return -EIO;
if (training_state == TS_ADJUST_LINK_RATE ||
training_state == TS_ADJUST_LANE_COUNT) {
if (!dp_tx->train_adaptive)
return -EIO;
status = set_training_pattern(dev,
TRAINING_PATTERN_SET_OFF);
if (status)
return -EIO;
}
}
/* Final status check. */
status = check_link_status(dev, dp_tx->link_config.lane_count);
if (status)
return -EIO;
return 0;
}
/* Link policy maker */
/**
* cfg_main_link_max() - Determine best common capabilities
* @dev: The LogiCore DP TX device in question
*
* Determine the common capabilities between the DisplayPort TX core and the RX
* device.
*
* Return: 0 if the determination succeeded, -ve on error
*/
static int cfg_main_link_max(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
if (!is_connected(dev))
return -ENODEV;
/*
* Configure the main link to the maximum common link rate between the
* DisplayPort TX core and the RX device.
*/
status = set_link_rate(dev, dp_tx->link_config.max_link_rate);
if (status)
return status;
/*
* Configure the main link to the maximum common lane count between the
* DisplayPort TX core and the RX device.
*/
status = set_lane_count(dev, dp_tx->link_config.max_lane_count);
if (status)
return status;
return 0;
}
/**
* establish_link() - Establish a link
* @dev: The LogiCore DP TX device in question
*
* Check if the link needs training and run the training sequence if training
* is required.
*
* Return: 0 if the link was established successfully, -ve on error
*/
static int establish_link(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int status;
int status2;
u32 mask;
reset_dp_phy(dev, PHY_CONFIG_PHY_RESET_MASK);
/* Disable main link during training. */
disable_main_link(dev);
/* Wait for the PHY to be ready. */
mask = phy_status_lanes_ready_mask(dp_tx->max_lane_count);
status = wait_phy_ready(dev, mask);
if (status)
return -EIO;
/* Train main link. */
status = run_training(dev);
/* Turn off the training pattern and enable scrambler. */
status2 = set_training_pattern(dev, TRAINING_PATTERN_SET_OFF);
if (status || status2)
return -EIO;
return 0;
}
/*
* Stream policy maker
*/
/**
* cfg_msa_recalculate() - Calculate MSA parameters
* @dev: The LogiCore DP TX device in question
*
* Calculate the following Main Stream Attributes (MSA):
* - Transfer unit size
* - User pixel width
* - Horizontal total clock
* - Vertical total clock
* - misc_0
* - misc_1
* - Data per lane
* - Average number of bytes per transfer unit
* - Number of initial wait cycles
*
* These values are derived from:
* - Bits per color
* - Horizontal resolution
* - Vertical resolution
* - Horizontal blank start
* - Vertical blank start
* - Pixel clock (in KHz)
* - Horizontal sync polarity
* - Vertical sync polarity
* - Horizontal sync pulse width
* - Vertical sync pulse width
*/
static void cfg_msa_recalculate(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u32 video_bw;
u32 link_bw;
u32 words_per_line;
u8 bits_per_pixel;
struct main_stream_attributes *msa_config;
struct link_config *link_config;
msa_config = &dp_tx->main_stream_attributes;
link_config = &dp_tx->link_config;
/*
* Set the user pixel width to handle clocks that exceed the
* capabilities of the DisplayPort TX core.
*/
if (msa_config->override_user_pixel_width == 0) {
if (msa_config->pixel_clock_hz > 300000000 &&
link_config->lane_count == LANE_COUNT_SET_4) {
msa_config->user_pixel_width = 4;
} /*
* Xilinx driver used 75 MHz as a limit here, 150 MHZ should
* be more sane
*/
else if ((msa_config->pixel_clock_hz > 150000000) &&
(link_config->lane_count != LANE_COUNT_SET_1)) {
msa_config->user_pixel_width = 2;
} else {
msa_config->user_pixel_width = 1;
}
}
/* Compute the rest of the MSA values. */
msa_config->n_vid = 27 * 1000 * link_config->link_rate;
/* Miscellaneous attributes. */
if (msa_config->bits_per_color == 6)
msa_config->misc_0 = MAIN_STREAMX_MISC0_BDC_6BPC;
else if (msa_config->bits_per_color == 8)
msa_config->misc_0 = MAIN_STREAMX_MISC0_BDC_8BPC;
else if (msa_config->bits_per_color == 10)
msa_config->misc_0 = MAIN_STREAMX_MISC0_BDC_10BPC;
else if (msa_config->bits_per_color == 12)
msa_config->misc_0 = MAIN_STREAMX_MISC0_BDC_12BPC;
else if (msa_config->bits_per_color == 16)
msa_config->misc_0 = MAIN_STREAMX_MISC0_BDC_16BPC;
msa_config->misc_0 = (msa_config->misc_0 <<
MAIN_STREAMX_MISC0_BDC_SHIFT) |
(msa_config->y_cb_cr_colorimetry <<
MAIN_STREAMX_MISC0_YCBCR_COLORIMETRY_SHIFT) |
(msa_config->dynamic_range <<
MAIN_STREAMX_MISC0_DYNAMIC_RANGE_SHIFT) |
(msa_config->component_format <<
MAIN_STREAMX_MISC0_COMPONENT_FORMAT_SHIFT) |
(msa_config->synchronous_clock_mode);
msa_config->misc_1 = 0;
/*
* Determine the number of bits per pixel for the specified color
* component format.
*/
if (msa_config->component_format ==
MAIN_STREAMX_MISC0_COMPONENT_FORMAT_YCBCR422)
/* YCbCr422 color component format. */
bits_per_pixel = msa_config->bits_per_color * 2;
else
/* RGB or YCbCr 4:4:4 color component format. */
bits_per_pixel = msa_config->bits_per_color * 3;
/* Calculate the data per lane. */
words_per_line = (msa_config->h_active * bits_per_pixel);
if (words_per_line % 16)
words_per_line += 16;
words_per_line /= 16;
msa_config->data_per_lane = words_per_line - link_config->lane_count;
if (words_per_line % link_config->lane_count)
msa_config->data_per_lane += (words_per_line %
link_config->lane_count);
/*
* Allocate a fixed size for single-stream transport (SST)
* operation.
*/
msa_config->transfer_unit_size = 64;
/*
* Calculate the average number of bytes per transfer unit.
* Note: Both the integer and the fractional part is stored in
* avg_bytes_per_tu.
*/
video_bw = ((msa_config->pixel_clock_hz / 1000) * bits_per_pixel) / 8;
link_bw = (link_config->lane_count * link_config->link_rate * 27);
msa_config->avg_bytes_per_tu = (video_bw *
msa_config->transfer_unit_size) /
link_bw;
/*
* The number of initial wait cycles at the start of a new line
* by the framing logic. This allows enough data to be buffered
* in the input FIFO before video is sent.
*/
if ((msa_config->avg_bytes_per_tu / 1000) <= 4)
msa_config->init_wait = 64;
else
msa_config->init_wait = msa_config->transfer_unit_size -
(msa_config->avg_bytes_per_tu / 1000);
}
/**
* set_line_reset() - Enable/Disable end-of-line-reset
* @dev: The LogiCore DP TX device in question
*
* Disable/enable the end-of-line-reset to the internal video pipe in case of
* reduced blanking as required.
*/
static void set_line_reset(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
u32 reg_val;
u16 h_blank;
u16 h_reduced_blank;
struct main_stream_attributes *msa_config =
&dp_tx->main_stream_attributes;
h_blank = msa_config->h_total - msa_config->h_active;
/* Reduced blanking starts at ceil(0.2 * HTotal). */
h_reduced_blank = 2 * msa_config->h_total;
if (h_reduced_blank % 10)
h_reduced_blank += 10;
h_reduced_blank /= 10;
/* CVT spec. states h_blank is either 80 or 160 for reduced blanking. */
reg_val = get_reg(dev, REG_LINE_RESET_DISABLE);
if (h_blank < h_reduced_blank &&
(h_blank == 80 || h_blank == 160)) {
reg_val |= LINE_RESET_DISABLE_MASK;
} else {
reg_val &= ~LINE_RESET_DISABLE_MASK;
}
set_reg(dev, REG_LINE_RESET_DISABLE, reg_val);
}
/**
* clear_msa_values() - Clear MSA values
* @dev: The LogiCore DP TX device in question
*
* Clear the main stream attributes registers of the DisplayPort TX core.
*/
static void clear_msa_values(struct udevice *dev)
{
set_reg(dev, REG_MAIN_STREAM_HTOTAL, 0);
set_reg(dev, REG_MAIN_STREAM_VTOTAL, 0);
set_reg(dev, REG_MAIN_STREAM_POLARITY, 0);
set_reg(dev, REG_MAIN_STREAM_HSWIDTH, 0);
set_reg(dev, REG_MAIN_STREAM_VSWIDTH, 0);
set_reg(dev, REG_MAIN_STREAM_HRES, 0);
set_reg(dev, REG_MAIN_STREAM_VRES, 0);
set_reg(dev, REG_MAIN_STREAM_HSTART, 0);
set_reg(dev, REG_MAIN_STREAM_VSTART, 0);
set_reg(dev, REG_MAIN_STREAM_MISC0, 0);
set_reg(dev, REG_MAIN_STREAM_MISC1, 0);
set_reg(dev, REG_USER_PIXEL_WIDTH, 0);
set_reg(dev, REG_USER_DATA_COUNT_PER_LANE, 0);
set_reg(dev, REG_M_VID, 0);
set_reg(dev, REG_N_VID, 0);
set_reg(dev, REG_STREAM1, 0);
set_reg(dev, REG_TU_SIZE, 0);
set_reg(dev, REG_MIN_BYTES_PER_TU, 0);
set_reg(dev, REG_FRAC_BYTES_PER_TU, 0);
set_reg(dev, REG_INIT_WAIT, 0);
}
/**
* set_msa_values() - Set MSA values
* @dev: The LogiCore DP TX device in question
*
* Set the main stream attributes registers of the DisplayPort TX
* core with the values specified in the main stream attributes configuration
* structure.
*/
static void set_msa_values(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
struct main_stream_attributes *msa_config =
&dp_tx->main_stream_attributes;
printf(" set MSA %u x %u\n", msa_config->h_active,
msa_config->v_active);
set_reg(dev, REG_MAIN_STREAM_HTOTAL, msa_config->h_total);
set_reg(dev, REG_MAIN_STREAM_VTOTAL, msa_config->v_total);
set_reg(dev, REG_MAIN_STREAM_POLARITY,
msa_config->h_sync_polarity |
(msa_config->v_sync_polarity <<
MAIN_STREAMX_POLARITY_VSYNC_POL_SHIFT));
set_reg(dev, REG_MAIN_STREAM_HSWIDTH, msa_config->h_sync_width);
set_reg(dev, REG_MAIN_STREAM_VSWIDTH, msa_config->v_sync_width);
set_reg(dev, REG_MAIN_STREAM_HRES, msa_config->h_active);
set_reg(dev, REG_MAIN_STREAM_VRES, msa_config->v_active);
set_reg(dev, REG_MAIN_STREAM_HSTART, msa_config->h_start);
set_reg(dev, REG_MAIN_STREAM_VSTART, msa_config->v_start);
set_reg(dev, REG_MAIN_STREAM_MISC0, msa_config->misc_0);
set_reg(dev, REG_MAIN_STREAM_MISC1, msa_config->misc_1);
set_reg(dev, REG_USER_PIXEL_WIDTH, msa_config->user_pixel_width);
set_reg(dev, REG_M_VID, msa_config->pixel_clock_hz / 1000);
set_reg(dev, REG_N_VID, msa_config->n_vid);
set_reg(dev, REG_USER_DATA_COUNT_PER_LANE, msa_config->data_per_lane);
set_line_reset(dev);
set_reg(dev, REG_TU_SIZE, msa_config->transfer_unit_size);
set_reg(dev, REG_MIN_BYTES_PER_TU, msa_config->avg_bytes_per_tu / 1000);
set_reg(dev, REG_FRAC_BYTES_PER_TU,
(msa_config->avg_bytes_per_tu % 1000) * 1024 / 1000);
set_reg(dev, REG_INIT_WAIT, msa_config->init_wait);
}
/*
* external API
*/
/**
* logicore_dp_tx_set_msa() - Set given MSA values on device
* @dev: The LogiCore DP TX device in question
* @msa: The MSA values to set for the device
*/
static void logicore_dp_tx_set_msa(struct udevice *dev,
struct logicore_dp_tx_msa *msa)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
memset(&dp_tx->main_stream_attributes, 0,
sizeof(struct main_stream_attributes));
dp_tx->main_stream_attributes.pixel_clock_hz = msa->pixel_clock_hz;
dp_tx->main_stream_attributes.bits_per_color = msa->bits_per_color;
dp_tx->main_stream_attributes.h_active = msa->h_active;
dp_tx->main_stream_attributes.h_start = msa->h_start;
dp_tx->main_stream_attributes.h_sync_polarity = msa->h_sync_polarity;
dp_tx->main_stream_attributes.h_sync_width = msa->h_sync_width;
dp_tx->main_stream_attributes.h_total = msa->h_total;
dp_tx->main_stream_attributes.v_active = msa->v_active;
dp_tx->main_stream_attributes.v_start = msa->v_start;
dp_tx->main_stream_attributes.v_sync_polarity = msa->v_sync_polarity;
dp_tx->main_stream_attributes.v_sync_width = msa->v_sync_width;
dp_tx->main_stream_attributes.v_total = msa->v_total;
dp_tx->main_stream_attributes.override_user_pixel_width =
msa->override_user_pixel_width;
dp_tx->main_stream_attributes.user_pixel_width = msa->user_pixel_width;
dp_tx->main_stream_attributes.synchronous_clock_mode = 0;
}
/**
* logicore_dp_tx_video_enable() - Enable video output
* @dev: The LogiCore DP TX device in question
* @msa: The MSA values to set for the device
*
* Return: 0 if the video was enabled successfully, -ve on error
*/
static int logicore_dp_tx_video_enable(struct udevice *dev,
struct logicore_dp_tx_msa *msa)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
int res;
u8 power = 0x01;
if (!is_connected(dev)) {
printf(" no DP sink connected\n");
return -EIO;
}
initialize(dev);
disable_main_link(dev);
logicore_dp_tx_set_msa(dev, msa);
get_rx_capabilities(dev);
printf(" DP sink connected\n");
aux_write(dev, DPCD_SET_POWER_DP_PWR_VOLTAGE, 1, &power);
set_enhanced_frame_mode(dev, true);
cfg_main_link_max(dev);
res = establish_link(dev);
printf(" establish_link: %s, vs: %d, pe: %d\n",
res ? "failed" : "ok", dp_tx->link_config.vs_level,
dp_tx->link_config.pe_level);
cfg_msa_recalculate(dev);
clear_msa_values(dev);
set_msa_values(dev);
enable_main_link(dev);
return 0;
}
/*
* Driver functions
*/
static int logicore_dp_tx_enable(struct udevice *dev, int panel_bpp,
const struct display_timing *timing)
{
struct clk pixclock;
struct logicore_dp_tx_msa *msa;
struct logicore_dp_tx_msa mode_640_480_60 = {
.pixel_clock_hz = 25175000,
.bits_per_color = 8,
.h_active = 640,
.h_start = 144,
.h_sync_polarity = false,
.h_sync_width = 96,
.h_total = 800,
.v_active = 480,
.v_start = 35,
.v_sync_polarity = false,
.v_sync_width = 2,
.v_total = 525,
.override_user_pixel_width = false,
.user_pixel_width = 0,
};
struct logicore_dp_tx_msa mode_720_400_70 = {
.pixel_clock_hz = 28300000,
.bits_per_color = 8,
.h_active = 720,
.h_start = 162,
.h_sync_polarity = false,
.h_sync_width = 108,
.h_total = 900,
.v_active = 400,
.v_start = 37,
.v_sync_polarity = true,
.v_sync_width = 2,
.v_total = 449,
.override_user_pixel_width = false,
.user_pixel_width = 0,
};
struct logicore_dp_tx_msa mode_1024_768_60 = {
.pixel_clock_hz = 65000000,
.bits_per_color = 8,
.h_active = 1024,
.h_start = 296,
.h_sync_polarity = false,
.h_sync_width = 136,
.h_total = 1344,
.v_active = 768,
.v_start = 35,
.v_sync_polarity = false,
.v_sync_width = 2,
.v_total = 806,
.override_user_pixel_width = false,
.user_pixel_width = 0,
};
if (timing->hactive.typ == 1024 && timing->vactive.typ == 768)
msa = &mode_1024_768_60;
else if (timing->hactive.typ == 720 && timing->vactive.typ == 400)
msa = &mode_720_400_70;
else
msa = &mode_640_480_60;
if (clk_get_by_index(dev, 0, &pixclock)) {
printf("%s: Could not get pixelclock\n", dev->name);
return -1;
}
clk_set_rate(&pixclock, msa->pixel_clock_hz);
return logicore_dp_tx_video_enable(dev, msa);
}
static int logicore_dp_tx_probe(struct udevice *dev)
{
struct dp_tx *dp_tx = dev_get_priv(dev);
dp_tx->s_axi_clk = S_AXI_CLK_DEFAULT;
dp_tx->train_adaptive = false;
dp_tx->max_link_rate = DPCD_MAX_LINK_RATE_540GBPS;
dp_tx->max_lane_count = DPCD_MAX_LANE_COUNT_4;
dp_tx->base = dev_read_u32_default(dev, "reg", -1);
return 0;
}
static const struct dm_display_ops logicore_dp_tx_ops = {
.enable = logicore_dp_tx_enable,
};
static const struct udevice_id logicore_dp_tx_ids[] = {
{ .compatible = "gdsys,logicore_dp_tx" },
{ /* sentinel */ }
};
U_BOOT_DRIVER(logicore_dp_tx) = {
.name = "logicore_dp_tx",
.id = UCLASS_DISPLAY,
.of_match = logicore_dp_tx_ids,
.probe = logicore_dp_tx_probe,
.priv_auto = sizeof(struct dp_tx),
.ops = &logicore_dp_tx_ops,
};
Reference in New Issue View Git Blame Copy Permalink