57a91c3c9e
This commit adds support for MMC controllers found on Actions OWL SoC platform(S700/S900). Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
409 lines
11 KiB
C
409 lines
11 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2020 Amit Singh Tomar <amittomer25@gmail.com>
|
|
*
|
|
* Driver for SD/MMC controller present on Actions Semi S700/S900 SoC, based
|
|
* on Linux Driver "drivers/mmc/host/owl-mmc.c".
|
|
*
|
|
* Though, there is a bit (BSEL, BUS or DMA Special Channel Selection) that
|
|
* controls the data transfer from SDx_DAT register either using CPU AHB Bus
|
|
* or DMA channel, but seems like, it only works correctly using external DMA
|
|
* channel, and those special bits used in this driver is picked from vendor
|
|
* source exclusively for MMC/SD.
|
|
*/
|
|
#include <common.h>
|
|
#include <clk.h>
|
|
#include <cpu_func.h>
|
|
#include <dm.h>
|
|
#include <errno.h>
|
|
#include <log.h>
|
|
#include <mmc.h>
|
|
#include <asm/io.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/err.h>
|
|
#include <linux/iopoll.h>
|
|
|
|
/*
|
|
* SDC registers
|
|
*/
|
|
#define OWL_REG_SD_EN 0x0000
|
|
#define OWL_REG_SD_CTL 0x0004
|
|
#define OWL_REG_SD_STATE 0x0008
|
|
#define OWL_REG_SD_CMD 0x000c
|
|
#define OWL_REG_SD_ARG 0x0010
|
|
#define OWL_REG_SD_RSPBUF0 0x0014
|
|
#define OWL_REG_SD_RSPBUF1 0x0018
|
|
#define OWL_REG_SD_RSPBUF2 0x001c
|
|
#define OWL_REG_SD_RSPBUF3 0x0020
|
|
#define OWL_REG_SD_RSPBUF4 0x0024
|
|
#define OWL_REG_SD_DAT 0x0028
|
|
#define OWL_REG_SD_BLK_SIZE 0x002c
|
|
#define OWL_REG_SD_BLK_NUM 0x0030
|
|
#define OWL_REG_SD_BUF_SIZE 0x0034
|
|
|
|
/* SD_EN Bits */
|
|
#define OWL_SD_EN_RANE BIT(31)
|
|
#define OWL_SD_EN_RESE BIT(10)
|
|
#define OWL_SD_ENABLE BIT(7)
|
|
#define OWL_SD_EN_BSEL BIT(6)
|
|
#define OWL_SD_EN_DATAWID(x) (((x) & 0x3) << 0)
|
|
#define OWL_SD_EN_DATAWID_MASK 0x03
|
|
|
|
/* SD_CTL Bits */
|
|
#define OWL_SD_CTL_TOUTEN BIT(31)
|
|
#define OWL_SD_CTL_DELAY_MSK GENMASK(23, 16)
|
|
#define OWL_SD_CTL_RDELAY(x) (((x) & 0xf) << 20)
|
|
#define OWL_SD_CTL_WDELAY(x) (((x) & 0xf) << 16)
|
|
#define OWL_SD_CTL_TS BIT(7)
|
|
#define OWL_SD_CTL_LBE BIT(6)
|
|
#define OWL_SD_CTL_TM(x) (((x) & 0xf) << 0)
|
|
|
|
#define OWL_SD_DELAY_LOW_CLK 0x0f
|
|
#define OWL_SD_DELAY_MID_CLK 0x0a
|
|
#define OWL_SD_RDELAY_HIGH 0x08
|
|
#define OWL_SD_WDELAY_HIGH 0x09
|
|
|
|
/* SD_STATE Bits */
|
|
#define OWL_SD_STATE_DAT0S BIT(7)
|
|
#define OWL_SD_STATE_CLNR BIT(4)
|
|
#define OWL_SD_STATE_CRC7ER BIT(0)
|
|
|
|
#define OWL_MMC_OCR (MMC_VDD_32_33 | MMC_VDD_33_34 | \
|
|
MMC_VDD_165_195)
|
|
|
|
#define DATA_TRANSFER_TIMEOUT 3000000
|
|
#define DMA_TRANSFER_TIMEOUT 5000000
|
|
|
|
/*
|
|
* Simple DMA transfer operations defines for MMC/SD card
|
|
*/
|
|
#define SD_DMA_CHANNEL(base, channel) ((base) + 0x100 + 0x100 * (channel))
|
|
|
|
#define DMA_MODE 0x0000
|
|
#define DMA_SOURCE 0x0004
|
|
#define DMA_DESTINATION 0x0008
|
|
#define DMA_FRAME_LEN 0x000C
|
|
#define DMA_FRAME_CNT 0x0010
|
|
#define DMA_START 0x0024
|
|
|
|
/* DMAx_MODE */
|
|
#define DMA_MODE_ST(x) (((x) & 0x3) << 8)
|
|
#define DMA_MODE_ST_DEV DMA_MODE_ST(0)
|
|
#define DMA_MODE_DT(x) (((x) & 0x3) << 10)
|
|
#define DMA_MODE_DT_DCU DMA_MODE_DT(2)
|
|
#define DMA_MODE_SAM(x) (((x) & 0x3) << 16)
|
|
#define DMA_MODE_SAM_CONST DMA_MODE_SAM(0)
|
|
#define DMA_MODE_DAM(x) (((x) & 0x3) << 18)
|
|
#define DMA_MODE_DAM_INC DMA_MODE_DAM(1)
|
|
|
|
#define DMA_ENABLE 0x1
|
|
|
|
struct owl_mmc_plat {
|
|
struct mmc_config cfg;
|
|
struct mmc mmc;
|
|
};
|
|
|
|
struct owl_mmc_priv {
|
|
void *reg_base;
|
|
void *dma_channel;
|
|
struct clk clk;
|
|
unsigned int clock; /* Current clock */
|
|
unsigned int dma_drq; /* Trigger Source */
|
|
};
|
|
|
|
static void owl_dma_config(struct owl_mmc_priv *priv, unsigned int src,
|
|
unsigned int dst, unsigned int len)
|
|
{
|
|
unsigned int mode = priv->dma_drq;
|
|
|
|
/* Set Source and Destination adderess mode */
|
|
mode |= (DMA_MODE_ST_DEV | DMA_MODE_SAM_CONST | DMA_MODE_DT_DCU |
|
|
DMA_MODE_DAM_INC);
|
|
|
|
writel(mode, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_MODE);
|
|
writel(src, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_SOURCE);
|
|
writel(dst, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_DESTINATION);
|
|
writel(len, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_FRAME_LEN);
|
|
writel(0x1, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_FRAME_CNT);
|
|
}
|
|
|
|
static void owl_mmc_prepare_data(struct owl_mmc_priv *priv,
|
|
struct mmc_data *data)
|
|
{
|
|
unsigned int total;
|
|
u32 buf = 0;
|
|
|
|
setbits_le32(priv->reg_base + OWL_REG_SD_EN, OWL_SD_EN_BSEL);
|
|
|
|
writel(data->blocks, priv->reg_base + OWL_REG_SD_BLK_NUM);
|
|
writel(data->blocksize, priv->reg_base + OWL_REG_SD_BLK_SIZE);
|
|
total = data->blocksize * data->blocks;
|
|
|
|
if (total < 512)
|
|
writel(total, priv->reg_base + OWL_REG_SD_BUF_SIZE);
|
|
else
|
|
writel(512, priv->reg_base + OWL_REG_SD_BUF_SIZE);
|
|
|
|
/* DMA STOP */
|
|
writel(0x0, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_START);
|
|
|
|
if (data) {
|
|
if (data->flags == MMC_DATA_READ) {
|
|
buf = (ulong) (data->dest);
|
|
owl_dma_config(priv, (ulong) priv->reg_base +
|
|
OWL_REG_SD_DAT, buf, total);
|
|
invalidate_dcache_range(buf, buf + total);
|
|
} else {
|
|
buf = (ulong) (data->src);
|
|
owl_dma_config(priv, buf, (ulong) priv->reg_base +
|
|
OWL_REG_SD_DAT, total);
|
|
flush_dcache_range(buf, buf + total);
|
|
}
|
|
/* DMA START */
|
|
writel(0x1, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_START);
|
|
}
|
|
}
|
|
|
|
static int owl_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
|
|
struct mmc_data *data)
|
|
{
|
|
struct owl_mmc_priv *priv = dev_get_priv(dev);
|
|
unsigned int cmd_rsp_mask, mode, reg;
|
|
int ret;
|
|
|
|
setbits_le32(priv->reg_base + OWL_REG_SD_EN, OWL_SD_ENABLE);
|
|
|
|
/* setup response */
|
|
mode = 0;
|
|
if (cmd->resp_type != MMC_RSP_NONE)
|
|
cmd_rsp_mask = OWL_SD_STATE_CLNR | OWL_SD_STATE_CRC7ER;
|
|
if (cmd->resp_type == MMC_RSP_R1) {
|
|
if (data) {
|
|
if (data->flags == MMC_DATA_READ)
|
|
mode |= OWL_SD_CTL_TM(4);
|
|
else
|
|
mode |= OWL_SD_CTL_TM(5);
|
|
} else
|
|
mode |= OWL_SD_CTL_TM(1);
|
|
} else if (cmd->resp_type == MMC_RSP_R2) {
|
|
mode = OWL_SD_CTL_TM(2);
|
|
} else if (cmd->resp_type == MMC_RSP_R1b) {
|
|
mode = OWL_SD_CTL_TM(3);
|
|
} else if (cmd->resp_type == MMC_RSP_R3) {
|
|
cmd_rsp_mask = OWL_SD_STATE_CLNR;
|
|
mode = OWL_SD_CTL_TM(1);
|
|
}
|
|
|
|
mode |= (readl(priv->reg_base + OWL_REG_SD_CTL) & (0xff << 16));
|
|
|
|
/* setup command */
|
|
writel(cmd->cmdidx, priv->reg_base + OWL_REG_SD_CMD);
|
|
writel(cmd->cmdarg, priv->reg_base + OWL_REG_SD_ARG);
|
|
|
|
/* Set LBE to send clk at the end of last read block */
|
|
if (data)
|
|
mode |= (OWL_SD_CTL_TS | OWL_SD_CTL_LBE | 0xE4000000);
|
|
else
|
|
mode |= OWL_SD_CTL_TS;
|
|
|
|
if (data)
|
|
owl_mmc_prepare_data(priv, data);
|
|
|
|
/* Start transfer */
|
|
writel(mode, priv->reg_base + OWL_REG_SD_CTL);
|
|
|
|
ret = readl_poll_timeout(priv->reg_base + OWL_REG_SD_CTL, reg,
|
|
!(reg & OWL_SD_CTL_TS), DATA_TRANSFER_TIMEOUT);
|
|
|
|
if (ret == -ETIMEDOUT) {
|
|
debug("error: transferred data timeout\n");
|
|
return ret;
|
|
}
|
|
|
|
reg = readl(priv->reg_base + OWL_REG_SD_STATE) & cmd_rsp_mask;
|
|
if (cmd->resp_type & MMC_RSP_PRESENT) {
|
|
if (reg & OWL_SD_STATE_CLNR) {
|
|
printf("Error CMD_NO_RSP\n");
|
|
return -1;
|
|
}
|
|
|
|
if (reg & OWL_SD_STATE_CRC7ER) {
|
|
printf("Error CMD_RSP_CRC\n");
|
|
return -1;
|
|
}
|
|
|
|
if (cmd->resp_type & MMC_RSP_136) {
|
|
cmd->response[3] = readl(priv->reg_base + OWL_REG_SD_RSPBUF0);
|
|
cmd->response[2] = readl(priv->reg_base + OWL_REG_SD_RSPBUF1);
|
|
cmd->response[1] = readl(priv->reg_base + OWL_REG_SD_RSPBUF2);
|
|
cmd->response[0] = readl(priv->reg_base + OWL_REG_SD_RSPBUF3);
|
|
} else {
|
|
u32 rsp[2];
|
|
|
|
rsp[0] = readl(priv->reg_base + OWL_REG_SD_RSPBUF0);
|
|
rsp[1] = readl(priv->reg_base + OWL_REG_SD_RSPBUF1);
|
|
cmd->response[0] = rsp[1] << 24 | rsp[0] >> 8;
|
|
cmd->response[1] = rsp[1] >> 8;
|
|
}
|
|
}
|
|
|
|
if (data) {
|
|
ret = readl_poll_timeout(SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_START,
|
|
reg, !(reg & DMA_ENABLE), DMA_TRANSFER_TIMEOUT);
|
|
|
|
if (ret == -ETIMEDOUT) {
|
|
debug("error: DMA transfer timeout\n");
|
|
return ret;
|
|
}
|
|
|
|
/* DMA STOP */
|
|
writel(0x0, SD_DMA_CHANNEL(priv->dma_channel, 0) + DMA_START);
|
|
/* Transmission STOP */
|
|
while (readl(priv->reg_base + OWL_REG_SD_CTL) & OWL_SD_CTL_TS)
|
|
clrbits_le32(priv->reg_base + OWL_REG_SD_CTL,
|
|
OWL_SD_CTL_TS);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int owl_mmc_clk_set(struct owl_mmc_priv *priv, int rate)
|
|
{
|
|
u32 reg, wdelay, rdelay;
|
|
|
|
reg = readl(priv->reg_base + OWL_REG_SD_CTL);
|
|
reg &= ~OWL_SD_CTL_DELAY_MSK;
|
|
|
|
/* Set RDELAY and WDELAY based on the clock */
|
|
if (rate <= 1000000)
|
|
rdelay = wdelay = OWL_SD_DELAY_LOW_CLK;
|
|
else if ((rate > 1000000) && (rate <= 26000000))
|
|
rdelay = wdelay = OWL_SD_DELAY_MID_CLK;
|
|
else if ((rate > 26000000) && (rate <= 52000000)) {
|
|
rdelay = OWL_SD_RDELAY_HIGH;
|
|
wdelay = OWL_SD_WDELAY_HIGH;
|
|
} else {
|
|
debug("SD clock rate not supported\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
writel(reg | OWL_SD_CTL_RDELAY(rdelay) | OWL_SD_CTL_WDELAY(wdelay),
|
|
priv->reg_base + OWL_REG_SD_CTL);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int owl_mmc_set_ios(struct udevice *dev)
|
|
{
|
|
struct owl_mmc_priv *priv = dev_get_priv(dev);
|
|
struct owl_mmc_plat *plat = dev_get_plat(dev);
|
|
struct mmc *mmc = &plat->mmc;
|
|
u32 reg, ret;
|
|
|
|
if (mmc->clock != priv->clock) {
|
|
priv->clock = mmc->clock;
|
|
ret = owl_mmc_clk_set(priv, mmc->clock);
|
|
if (IS_ERR_VALUE(ret))
|
|
return ret;
|
|
|
|
ret = clk_set_rate(&priv->clk, mmc->clock);
|
|
if (IS_ERR_VALUE(ret))
|
|
return ret;
|
|
}
|
|
|
|
if (mmc->clk_disable)
|
|
ret = clk_disable(&priv->clk);
|
|
else
|
|
ret = clk_enable(&priv->clk);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Set the Bus width */
|
|
reg = readl(priv->reg_base + OWL_REG_SD_EN);
|
|
reg &= ~OWL_SD_EN_DATAWID_MASK;
|
|
if (mmc->bus_width == 8)
|
|
reg |= OWL_SD_EN_DATAWID(2);
|
|
else if (mmc->bus_width == 4)
|
|
reg |= OWL_SD_EN_DATAWID(1);
|
|
|
|
writel(reg, priv->reg_base + OWL_REG_SD_EN);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct dm_mmc_ops owl_mmc_ops = {
|
|
.send_cmd = owl_mmc_send_cmd,
|
|
.set_ios = owl_mmc_set_ios,
|
|
};
|
|
|
|
static int owl_mmc_probe(struct udevice *dev)
|
|
{
|
|
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
|
|
struct owl_mmc_plat *plat = dev_get_plat(dev);
|
|
struct owl_mmc_priv *priv = dev_get_priv(dev);
|
|
struct mmc_config *cfg = &plat->cfg;
|
|
struct ofnode_phandle_args args;
|
|
int ret;
|
|
fdt_addr_t addr;
|
|
|
|
cfg->name = dev->name;
|
|
cfg->voltages = OWL_MMC_OCR;
|
|
cfg->f_min = 400000;
|
|
cfg->f_max = 52000000;
|
|
cfg->b_max = 512;
|
|
cfg->host_caps = MMC_MODE_HS | MMC_MODE_HS_52MHz;
|
|
|
|
ret = mmc_of_parse(dev, cfg);
|
|
if (ret)
|
|
return ret;
|
|
|
|
addr = dev_read_addr(dev);
|
|
if (addr == FDT_ADDR_T_NONE)
|
|
return -EINVAL;
|
|
|
|
priv->reg_base = (void *)addr;
|
|
|
|
ret = dev_read_phandle_with_args(dev, "dmas", "#dma-cells", 0, 0,
|
|
&args);
|
|
if (ret)
|
|
return ret;
|
|
|
|
priv->dma_channel = (void *)ofnode_get_addr(args.node);
|
|
priv->dma_drq = args.args[0];
|
|
|
|
ret = clk_get_by_index(dev, 0, &priv->clk);
|
|
if (ret) {
|
|
debug("clk_get_by_index() failed: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
upriv->mmc = &plat->mmc;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int owl_mmc_bind(struct udevice *dev)
|
|
{
|
|
struct owl_mmc_plat *plat = dev_get_plat(dev);
|
|
|
|
return mmc_bind(dev, &plat->mmc, &plat->cfg);
|
|
}
|
|
|
|
static const struct udevice_id owl_mmc_ids[] = {
|
|
{ .compatible = "actions,s700-mmc" },
|
|
{ .compatible = "actions,owl-mmc" },
|
|
{ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(owl_mmc_drv) = {
|
|
.name = "owl_mmc",
|
|
.id = UCLASS_MMC,
|
|
.of_match = owl_mmc_ids,
|
|
.bind = owl_mmc_bind,
|
|
.probe = owl_mmc_probe,
|
|
.ops = &owl_mmc_ops,
|
|
.plat_auto = sizeof(struct owl_mmc_plat),
|
|
.priv_auto = sizeof(struct owl_mmc_priv),
|
|
};
|