a9c3bce362
This converts the following to Kconfig: CONFIG_USB_GADGET_AT91 Signed-off-by: Tom Rini <trini@konsulko.com>
105 lines
2.9 KiB
Plaintext
105 lines
2.9 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT_ONLY=y
|
|
CONFIG_SPL_SKIP_LOWLEVEL_INIT_ONLY=y
|
|
CONFIG_SPL_SYS_ICACHE_OFF=y
|
|
CONFIG_SPL_SYS_DCACHE_OFF=y
|
|
CONFIG_SPL_SYS_THUMB_BUILD=y
|
|
# CONFIG_SPL_USE_ARCH_MEMCPY is not set
|
|
# CONFIG_SPL_USE_ARCH_MEMSET is not set
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_TEXT_BASE=0x23000000
|
|
CONFIG_SYS_MALLOC_LEN=0x460000
|
|
CONFIG_TARGET_SMARTWEB=y
|
|
CONFIG_AT91_GPIO_PULLUP=y
|
|
CONFIG_ATMEL_LEGACY=y
|
|
CONFIG_SPL_GPIO=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_OFFSET=0x100000
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91sam9260-smartweb"
|
|
CONFIG_SYS_PROMPT="U-Boot# "
|
|
CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
|
|
CONFIG_SPL=y
|
|
CONFIG_ENV_OFFSET_REDUND=0x180000
|
|
CONFIG_SYS_LOAD_ADDR=0x22000000
|
|
CONFIG_FIT=y
|
|
CONFIG_NAND_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_AUTOBOOT_KEYED=y
|
|
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
|
|
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="run flashboot"
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_SPL_MAX_SIZE=0x1000
|
|
CONFIG_SPL_PAD_TO=0x20000
|
|
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
|
|
CONFIG_SPL_BSS_START_ADDR=0x20000000
|
|
CONFIG_SPL_BSS_MAX_SIZE=0x4000
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_SPL_STACK=0x301000
|
|
CONFIG_SYS_SPL_MALLOC=y
|
|
CONFIG_SYS_SPL_MALLOC_SIZE=0x460000
|
|
CONFIG_SPL_NAND_SUPPORT=y
|
|
CONFIG_SPL_NAND_RAW_ONLY=y
|
|
CONFIG_SPL_NAND_DRIVERS=y
|
|
CONFIG_SPL_NAND_ECC=y
|
|
CONFIG_SPL_NAND_SOFTECC=y
|
|
CONFIG_SPL_NAND_BASE=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_MAXARGS=32
|
|
CONFIG_SYS_CBSIZE=512
|
|
CONFIG_SYS_PBSIZE=537
|
|
# CONFIG_CMD_IMI is not set
|
|
CONFIG_CMD_DFU=y
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_NAND=y
|
|
# CONFIG_CMD_SOURCE is not set
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_BOOTP_BOOTFILESIZE=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_MTDIDS_DEFAULT="nand0=atmel_nand"
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=atmel_nand:128k(Bootstrap),896k(U-Boot),512k(ENV0),512k(ENV1),4M(Linux),-(Root-FS)"
|
|
# CONFIG_DOS_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_OF_EMBED=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_NAND=y
|
|
CONFIG_ENV_RANGE=0x80000
|
|
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_NET_RETRY_COUNT=20
|
|
CONFIG_CLK=y
|
|
CONFIG_CLK_AT91=y
|
|
CONFIG_DFU_NAND=y
|
|
CONFIG_SYS_DFU_DATA_BUF_SIZE=0x100000
|
|
CONFIG_AT91_GPIO=y
|
|
# CONFIG_MMC is not set
|
|
CONFIG_MTD=y
|
|
# CONFIG_SYS_NAND_USE_FLASH_BBT is not set
|
|
CONFIG_NAND_ATMEL=y
|
|
CONFIG_SYS_NAND_BLOCK_SIZE=0x20000
|
|
CONFIG_SYS_NAND_PAGE_COUNT=0x40
|
|
CONFIG_SYS_NAND_PAGE_SIZE=0x800
|
|
CONFIG_SYS_NAND_OOBSIZE=0x40
|
|
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
|
|
CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000
|
|
CONFIG_MACB=y
|
|
CONFIG_RMII=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_ATMEL=y
|
|
CONFIG_USB_GADGET=y
|
|
CONFIG_USB_GADGET_MANUFACTURER="Siemens AG"
|
|
CONFIG_USB_GADGET_VENDOR_NUM=0x0908
|
|
CONFIG_USB_GADGET_PRODUCT_NUM=0x02d2
|
|
CONFIG_USB_GADGET_AT91=y
|
|
CONFIG_USB_GADGET_DOWNLOAD=y
|
|
CONFIG_WDT=y
|
|
CONFIG_WDT_AT91=y
|
|
CONFIG_SPL_TINY_MEMSET=y
|