08574ed339
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
115 lines
3.0 KiB
Plaintext
115 lines
3.0 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_ARCH_CPU_INIT=y
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_TEXT_BASE=0x26f00000
|
|
CONFIG_TARGET_SAMA5D4EK=y
|
|
CONFIG_SPL_GPIO=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x6000
|
|
CONFIG_ENV_SECT_SIZE=0x1000
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_SPL_DM_SPI=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d4ek"
|
|
CONFIG_SPL_TEXT_BASE=0x200000
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL_DRIVERS_MISC=y
|
|
CONFIG_SPL=y
|
|
CONFIG_DEBUG_UART_BASE=0xfc00c000
|
|
CONFIG_DEBUG_UART_CLOCK=88000000
|
|
CONFIG_DEBUG_UART_BOARD_INIT=y
|
|
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
|
CONFIG_SPL_SPI=y
|
|
CONFIG_SYS_LOAD_ADDR=0x22000000
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_ENV_VARS_UBOOT_CONFIG=y
|
|
CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
|
|
CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20003ee0
|
|
CONFIG_SYS_MONITOR_LEN=524288
|
|
CONFIG_FIT=y
|
|
CONFIG_SPI_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256K(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=6 root=ubi0:rootfs"
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="sf probe 0; sf read 0x21000000 0x60000 0xc000; sf read 0x22000000 0x6c000 0x394000; bootz 0x22000000 - 0x21000000"
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_SPL_MAX_SIZE=0x18000
|
|
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
|
|
CONFIG_SPL_BSS_START_ADDR=0x20000000
|
|
CONFIG_SPL_BSS_MAX_SIZE=0x80000
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_SPL_STACK=0x218000
|
|
CONFIG_SYS_SPL_MALLOC=y
|
|
CONFIG_SYS_SPL_MALLOC_SIZE=0x80000
|
|
CONFIG_SPL_DM_SPI_FLASH=y
|
|
CONFIG_SPL_SPI_LOAD=y
|
|
CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_CBSIZE=256
|
|
CONFIG_SYS_PBSIZE=276
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_IMI is not set
|
|
# CONFIG_CMD_FLASH is not set
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_BOOTP_BOOTFILESIZE=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dma-names dmas"
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_SPL_DM_SEQ_ALIAS=y
|
|
CONFIG_CLK=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_CLK_AT91=y
|
|
CONFIG_AT91_UTMI=y
|
|
CONFIG_AT91_H32MX=y
|
|
CONFIG_AT91_GPIO=y
|
|
CONFIG_GENERIC_ATMEL_MCI=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_ATMEL=y
|
|
CONFIG_ATMEL_NAND_HW_PMECC=y
|
|
CONFIG_PMECC_CAP=8
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
|
|
CONFIG_SYS_NAND_U_BOOT_OFFS=0x40000
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_SPEED=30000000
|
|
CONFIG_SPI_FLASH_ATMEL=y
|
|
CONFIG_MACB=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_SPL_PINCTRL=y
|
|
CONFIG_PINCTRL_AT91=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_SYSRESET=y
|
|
CONFIG_SPL_SYSRESET=y
|
|
CONFIG_SYSRESET_AT91=y
|
|
CONFIG_TIMER=y
|
|
CONFIG_SPL_TIMER=y
|
|
CONFIG_ATMEL_PIT_TIMER=y
|
|
CONFIG_SPL_ATMEL_PIT_TIMER=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_STORAGE=y
|
|
CONFIG_USB_GADGET=y
|
|
CONFIG_USB_GADGET_ATMEL_USBA=y
|
|
CONFIG_VIDEO=y
|
|
# CONFIG_VIDEO_BPP8 is not set
|
|
# CONFIG_VIDEO_BPP32 is not set
|
|
CONFIG_ATMEL_HLCD=y
|