08574ed339
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
101 lines
2.6 KiB
Plaintext
101 lines
2.6 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_IMX8M=y
|
|
CONFIG_TEXT_BASE=0x40200000
|
|
CONFIG_SYS_MALLOC_LEN=0x600000
|
|
CONFIG_SPL_GPIO=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_ENV_SIZE=0x1000
|
|
CONFIG_ENV_OFFSET=0x400000
|
|
CONFIG_SYS_I2C_MXC_I2C1=y
|
|
CONFIG_SYS_I2C_MXC_I2C2=y
|
|
CONFIG_SYS_I2C_MXC_I2C3=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="imx8mq-pico-pi"
|
|
CONFIG_SPL_TEXT_BASE=0x7E1000
|
|
CONFIG_TARGET_PICO_IMX8MQ=y
|
|
CONFIG_SPL_MMC=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL_DRIVERS_MISC=y
|
|
CONFIG_SPL=y
|
|
CONFIG_IMX_BOOTAUX=y
|
|
CONFIG_SYS_LOAD_ADDR=0x40480000
|
|
CONFIG_REMAKE_ELF=y
|
|
CONFIG_SYS_MONITOR_LEN=524288
|
|
CONFIG_FIT=y
|
|
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
|
|
CONFIG_SPL_LOAD_FIT=y
|
|
# CONFIG_USE_SPL_FIT_GENERATOR is not set
|
|
CONFIG_OF_SYSTEM_SETUP=y
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else booti ${loadaddr} - ${fdt_addr}; fi"
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_BOARD_LATE_INIT=y
|
|
CONFIG_SPL_MAX_SIZE=0x1f000
|
|
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
|
|
CONFIG_SPL_BSS_START_ADDR=0x180000
|
|
CONFIG_SPL_BSS_MAX_SIZE=0x2000
|
|
CONFIG_SPL_BOARD_INIT=y
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_SPL_STACK=0x187ff0
|
|
CONFIG_SYS_SPL_MALLOC=y
|
|
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
|
|
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x42200000
|
|
CONFIG_SYS_SPL_MALLOC_SIZE=0x80000
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_POWER=y
|
|
CONFIG_SPL_WATCHDOG=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_MAXARGS=64
|
|
# CONFIG_BOOTM_NETBSD is not set
|
|
CONFIG_SYS_BOOTM_LEN=0x8000000
|
|
# CONFIG_CMD_EXPORTENV is not set
|
|
# CONFIG_CMD_IMPORTENV is not set
|
|
# CONFIG_CMD_CRC32 is not set
|
|
CONFIG_CMD_FUSE=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_REGULATOR=y
|
|
CONFIG_CMD_EXT2=y
|
|
CONFIG_CMD_EXT4=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_SYS_MMC_ENV_DEV=1
|
|
CONFIG_USE_ETHPRIME=y
|
|
CONFIG_ETHPRIME="FEC"
|
|
CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
|
|
CONFIG_MXC_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_SPL_SYS_I2C_LEGACY=y
|
|
CONFIG_SUPPORT_EMMC_BOOT=y
|
|
CONFIG_FSL_USDHC=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_ATHEROS=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_FEC_MXC=y
|
|
CONFIG_MII=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_PINCTRL_IMX8M=y
|
|
CONFIG_SPL_POWER_LEGACY=y
|
|
CONFIG_POWER_DOMAIN=y
|
|
CONFIG_IMX8M_POWER_DOMAIN=y
|
|
CONFIG_DM_REGULATOR=y
|
|
CONFIG_DM_REGULATOR_FIXED=y
|
|
CONFIG_DM_REGULATOR_GPIO=y
|
|
CONFIG_SPL_POWER_I2C=y
|
|
CONFIG_DM_RESET=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_MXC_UART=y
|
|
CONFIG_DM_THERMAL=y
|