u-boot/configs/at91sam9g20ek_dataflash_cs0_defconfig
Samuel Holland f4917b4933 usb: ohci: Use a flexible array member for portstatus
The struct is only used to overlay the MMIO region, so the behavior is
the same. This obsoletes the Kconfig option for the number of ports.

Signed-off-by: Samuel Holland <samuel@sholland.org>
2022-11-03 23:24:09 +01:00

68 lines
1.7 KiB
Plaintext

CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_ARCH_CPU_INIT=y
CONFIG_ARCH_AT91=y
CONFIG_TEXT_BASE=0x21f00000
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_TARGET_AT91SAM9260EK=y
CONFIG_ATMEL_LEGACY=y
CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_ENV_SECT_SIZE=0x210
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek"
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_DEBUG_UART_BASE=0xfffff200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_DEBUG_UART=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="sf probe 0:0; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_CBSIZE=256
CONFIG_SYS_PBSIZE=281
# CONFIG_CMD_BDI is not set
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_NAND=y
# CONFIG_CMD_SOURCE is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_BOOTP_BOOTFILESIZE=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_ATMEL=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_DATAFLASH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_SYS_USB_OHCI_SLOT_NAME="at91sam9260"
CONFIG_USB_ATMEL=y