Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Move the SATA options inside an 'if SATA' part, so they are grouped.
Fix the 'Complient' typo while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_FSL_ENETC is not explicitly enabled in the NXP LS1028A config
files, instead it is selected by CONFIG_MSCC_FELIX_SWITCH, a state of
matters which is fragile.
CONFIG_MSCC_FELIX_SWITCH depends on CONFIG_DM_DSA, which depends on
CONFIG_PHY_FIXED.
Not all LS1028A boards did enable CONFIG_PHY_FIXED, which resulted in
all of Ethernet being compiled out.
This patch makes sure that CONFIG_PHY_FIXED is enabled for all LS1028A
boards, and CONFIG_FSL_ENETC as well - don't rely on that fragile
selection done by the Felix switch config.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
LS1028A-QDS has CONFIG_SPI_FLASH_SST and CONFIG_SPI_FLASH_EON defines
present in header. Move these entries from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no Spansion flash on LS1028A-RDB/QDS boards.
Unset CONFIG_SPI_FLASH_SPANSION option for both the boards.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The switch driver for LS1028A Ethernet switch is now compiled in for
the NXP LS1028A reference design boards and for the Kontron SMARC-sAL28.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable FSPI controller support. So, flash environment can now be used
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1028A QDS boards have a MDIO MUX and they require the driver for it for
PHYs to work.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
setexpr command is used while running secure boot
(chain of trust with confidentiality) feature.
Enable CONFIG_CMD_SETEXPR to enable setexpr command.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since at least some of the drivers relevant to LS1028A are now following
DM, it's useful to have dm command enabled by default.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
