Fix loop in board_fix_fdt that erroneously increments the counter
in all cases whereas the counter should be incremented only if a
matching string has been found.
Fixes: 5d535aa40b ("board: fsl: lx2160a: implement board_fix_fdt")
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Exports the serdes configuration as an environment variable for LS gen 3
SoCs, so it can be used in u-boot command line. It should particularly
be useful for applying Linux DT overlays for the given serdes
configuration.
This code is called from arch_misc_init and not from the existing
serdes_init function because it depends on U-Boot environment being set
up.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add serdes protocol 0x7777, 0x9999, 0xb998, 0xbb56 to supported list.
These protocols are supported and functional but they trigger a warning
in U-Boot console at boot because they are not on this list.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Separate MAC and serdes configuration, MAC configuration must be applied
at each enetc_start() as FLR clears it.
This restores traffic for ENETC interfaces in USXGMII mode.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The linux kernel Image is growing quite quickly,
if kernel Image size grow beyond 36 MB then
kernel Image at load address 0x81000000
overlaps with the reserved memory region
at 0x83400000.
Adjust kernel load address(kernel_addr_r) from
0x81000000 to 0x96000000 to avoid kernel Image
overlapping with reserved memory region.
This change fixes the below U-Boot error while
booting uncompressed kernel Image through booti command,
ERROR: reserving fdt memory region failed (addr=83400000 size=c00000)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The linux kernel Image is growing quite quickly,
if kernel Image size grow beyond 36 MB then
kernel Image at load address 0x81000000
overlaps with the reserved memory region
at 0x83400000.
Adjust kernel load address(kernel_addr_r) from
0x81000000 to 0x96000000 to avoid kernel Image
overlapping with reserved memory region.
This change fixes the below U-Boot error while
booting uncompressed kernel Image through booti command,
ERROR: reserving fdt memory region failed (addr=83400000 size=c00000)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1088A has four personalities, LS1088A, LS1084A, LS1048A and LS1044A.
LS1044A, LS1048A are LS1088A personalities, which support only one
1x 10GE port.
MAC1 and MAC2 are associated with 1G SGMII, 2.5G SGMII, and XFI.
Disable MAC1 to have only one 1x 10GE port for LS1044A, LS1048A.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
These config entries are inside the menu block, which already
depends on ARCH_LS1021A:
menu "LS102xA architecture"
depends on ARCH_LS1021A
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The dts node of the DSPI controller in kernel is spi instead of dspi,
it is not correct if use "/soc/dspi@" to fix up the status of the dts
in kernel, so, modify it to "/soc/spi@".
The DSPI2 and I2C5 are muxed, and the status of DSPI2 node in kernel dts
default value is okay, So set the status of DSPI2 node in kernel dts to
disabled if it is muxed as I2C5.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev1 and rev2 SoC has different pcie controller.
The pcie controller device tree node fields "compatible"
and registers names needs to be updated accordingly.
Enable CONFIG_OF_BOARD_FIXUP to apply board_fix_fdt
which updates the "compatible" and registers names.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev1 requires layerscape_gen4 device tree fixup and
lx2160a rev2 requires layerscape device tree fixup.
Add device tree fixup for lx2160a based on SoC and Version.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move streamId allocation to layerscape common device tree fixup.
Calculate streamId based on SoC variant.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Common device tree fixup for NXP SoCs. Based on
SoC and revision call pcie_layerscape or pcie_layerscape_gen4
fixup.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBRDSNP and
SCFG_SNPCNFGCR_USBWRSNP to drive USB read/write
snoop signal on LS1012A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1028A SoC is special in the handling of the MAC addresses. We need
to write to the IERB version of the PSIPMAR0/1 register. This value will
be sampled into the corresponding port PSIPMAR0/1 register if the PCI
memory access is enabled.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Intead of setting the MAC address in enetc_start() use the proper
write_hwaddr(). U-Boot takes care of the random MAC address, too.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is not any difference for disabling BARs in RC mode
between PCIe controllers with and without SRIOV.
Fixes: 80afc63fc3 ("pci: layerscape: add pci driver based on DM")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The software will still get non-zero Expansion ROM BAR size
even when the BAR_EN bit is cleared. The BAR_EN bit of
register EXP_ROM_BAR_MASK_RC is not working as expected,
so this patch changes to mask all the bits.
Fixes: 80afc63fc3 ("pci: layerscape: add pci driver based on DM")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1012afwry
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1088ardb
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1046afrwy
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
div_by is a misleading parameter name, when we are doing >> div_by.
Rename it to right_shift.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
FIT image contents can be larger than default bootm limit 8M
with initrd. Raise limit to 64MB which is commonly used
elsewhere.
Signed-off-by: Dhananjay Phadke <dphadke@linux.microsoft.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This board is similar to SUV31, but the FPGA is reset concept is quite
different.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the possibility in both debug and ramfs modes to
optionally load an env file from /tftpboot/$tftppath (this is ignored if
not present, so the change is backward compatible). This gives the debug
and ramfs scripts the possibility to set uboot environment variables
that were previously asked the users to manually set (nfs path in debug
and rootfs size in ramfs).
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Tom Rini <trini@konsulko.com>
The tftppath was not set in case of run ramfs. It worked only by chance
if was already set before.
Also check the boardname before setting the tftppath for COGE5.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Tom Rini <trini@konsulko.com>
The CPUWD reset reason is used for kmp204x.
And the qrio cpu reset request is configured to operate in
core reset mode.
But for the evaluation of the qrio's reset reason register
the CPUWD figures as a unit reset source rather than a core
reset source. This patch defines the CPUWD reset as a core
reset source when evaluating the reset reason register.
Signed-off-by: Rainer Boschung <rainer.boschung@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the qrio and i2c deblocking code to
keymile/common as it will also be used by the upcoming CENT2 board.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
This prevents the board from booting which is not the expected behavior.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Take up maintainership of random number generator drivers with
Heinrich Schuchardt as the reviewer.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When using fitImage in AARCH64, the fdt is only 4 byte aligned.
According to linux kernel -> Documentation/arm64/booting.txt, the
fdt *must* be 8 byte aligned. Therefore, it is somewhat random,
if you build a kernel that the fdt is 4 or 8 byte aligned.
Removing fdt_high (or changing it to a valid 8 byte aligned
address) solves this issue.
Signed-off-by: Matthias Schoepfer <matthias.schoepfer@ithinx.io>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm68360.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
