Add pinctrl_get_pin_name() and pinctrl_get_pins_count() methods
to obtain pin's name and pin's muxing given a pin reference.
This will be used by the new pinmux command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pin_muxing() which allows to display the muxing
of a given pin belonging to a pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
README.omap3 has two options. For option 1, CONFIG_SYS_TEXT_BASE
is set to 0x80100000. Option 2 lists 0x80008000. The existing
value is neither of these, so this patch makes it equivalent to
Option 1.
Signed-off-by: Adam Ford <aford173@gmail.com>
In an effort to free up more resources in SPL and U-Boot, building
for Thumb shrinks the code side.
Before:
text data bss dec hex filename
685588 25808 275724 987120 f0ff0 u-boot
text data bss dec hex filename
55324 417 67460 123201 1e141 spl/u-boot-spl
After:
text data bss dec hex filename
515502 25808 275708 817018 c777a u-boot
text data bss dec hex filename
42910 417 67460 110787 1b0c3 spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
The AM3517 is mostly am omap3, so this partch removes the custom
memory configurations and just uses the default common entries
for omap3 and armv7.
Signed-off-by: Adam Ford <aford173@gmail.com>
Some minor changes have been made to the AM3517-evm and the underlying
am3517.dtsi files. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
Testing and analysis shows that at the moment LPC32xx NAND SLC driver
can not get PL080 DMA backbone support in SPL build, because SPL NAND
loaders operate with subpage (ECC step to be precisely) reads, and
this is not supported in the NAND SLC + DMA + hardware ECC calculation
bundle.
The change removes a cautious build time warning and explicitly
disables DMA flavour of the driver for SPL builds, to reduce the
amound of #ifdef sections the code blocks are minimally reorganized.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Build option CONFIG_SYS_MAX_NAND_CHIPS is used by NXP LPC32xx NAND MLC
driver only, as a preparation for potential removal or replacement of
the option the change predefines CONFIG_SYS_MAX_NAND_CHIPS to 1, same
value is used by the single user Work Microwave Work 92105 board, thus
it will be safe now to remove the option as a board specific one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The pca953x_gpio driver uses default value of polarity inversion
register. For some devices like PCA9557 and MAX7310, their polarity
inversion register default value is 0xf0. So for high 4 ports, when
reading their values, the values are inverted as the actual level.
This patch clears the polarity inversion register to 0 at init, so
that the port read and write values are aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The earlier commit f4fcba5c5b ("clk: implement clk_set_defaults()")
which introduced the functionality for setting clock defaults such as
rates and parents will skip the processing when executing in a re-reloc
state. This for example can prevent the assigning of clock parents
when running in SPL code. Go ahead and remove this limitation.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This add the initial support of the broadcom reference
board bcm968580xref with a bcm6858 SoC.
This board has 512 MB of ram, 256 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Display all digits on 64bit systems. Currently we print only the lower
32 bits. Examples of values that can exceed 32 bits are the size and start of
memory banks.
For fdt_blob use the same output method as for other values. This avoids
misalignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Allow platform vendors to handle SError interrupt exceptions from
ARMv8 PSCI exception vectors by overriding this weak function
'plat_error_handler'.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Allow EL3 to handle all the External Abort and SError interrupt
exception occur in all exception levels.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
The clearfog, corvus, wb45n and picosam9g45 configs are close to
exceeding their size limits, so enable THUMB2 builds on them to reclaim
space.
Signed-off-by: Tom Rini <trini@konsulko.com>
The latest version of pytest (4.0.0) makes some of the code we have in
test/py/conftest.py a fatal error that needs to be migrated.
Unfortunately this in turn requires changes that don't exist in older
versions of pytest such as 2.8.7 that ships with Ubuntu 16.04. Force
travis to use this older version of pytest.
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit c5bbfaf05d.
Disabling CONFIG_DISPLAY_CPUINFO was a temporary solution to get
the v2018.11 release out. Now the merge window opens, revert it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support CONFIG_DISPLAY_CPUINFO, add "u-boot,dm-pre-reloc" for
all cpu nodes in Sandbox test.dts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
It turns out commit c0434407b5 broke some boards which have DM CPU
driver with CONFIG_DISPLAY_CPUINFO option on. These boards just fail
to boot when print_cpuinfo() is called during boot.
Fixes: c0434407b5 ("board_f: Use static print_cpuinfo if CONFIG_CPU is active")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Add some description about pre-relocation driver binding, including
usage of DM_FLAG_PRE_RELOC flag and caveats.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
If _debug_uart_putc() is called before _debug_uart_init(), the
ns16550 debug uart driver hangs in a tight loop waiting for the
tx FIFO to get empty.
As this can happen via a printf sneaking in before the port calls
debug_uart_init(), let's rather ignore characters before the debug
uart is initialized.
This is done by reading the baudrate divisor and aborting if is zero.
Tested on socfpga_cyclone5_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use the uclass_foreach_dev() macro instead of the open coded version.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add REAME.virtio to describe the information about U-Boot support for
VirtIO devices, including supported boards, build instructions, driver
details etc.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have a sandbox virtio transport driver, add some test
cases to test virtio uclass driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver provides support for Sandbox implementation of virtio
transport driver which is used for testing purpose only.
Two drivers are provided. The 2nd one is a driver that lacks the
'notify' op.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For v1.0 compliant device, it always assumes the member 'num_buffers'
exists in the struct virtio_net_hdr while the legacy driver only
presented 'num_buffers' when VIRTIO_NET_F_MRG_RXBUF was negotiated.
Without that feature the structure was 2 bytes shorter.
Update the driver to support the non-legacy device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default QEMU creates legacy PCI transport devices, but we can
ask QEMU to create non-legacy one if we pass additional device
property/value pairs in the command line:
-device virtio-blk-pci,disable-legacy=true,disable-modern=false
This adds a new driver driver to support non-legacy (modern) device
mode. Previous driver/file name is changed accordingly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test cases to cover the two newly added PCI APIs:
dm_pci_find_next_capability() & dm_pci_find_next_ext_capability().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces two new APIs dm_pci_find_next_capability() and
dm_pci_find_next_ext_capability() to get PCI capability address
and PCI express extended capability address for a given PCI device
starting from a given offset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently devices on the virtio bus is not automatically enumerated,
which means peripherals on the virtio bus are not discovered by their
drivers. This uses board_init() to do the virtio enumeration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
