i.MXRT1050 provides mxsfb compatible lcd controller, so let's enable
video mxsfb driver with 16bpp depth if CONFIG_DM_VIDEO is selected since
board has 16bpp only connection.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
ENABLE signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
DOTCLK signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
VSYNC signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
HSYNC signal can now be flipped according to display_flags bitmaks by
writing its bitmask on vdctrl0 register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
struct display_timings provides more informations such clock and DE
polarity, so let's refactor the code to use struct display_timings
instead of struct ctfb_res_modes, so we'll become able to get clock and
DE polarity settings and set register according to them in the next patch.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add support for i.MXRT by adding CONFIG_IMXRT in register structure and
adding .compatible = "fsl,imxrt-lcdif".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Allow using DM CLK instead of mxs_set_lcdclk() so we can avoid to
implement a special function to set lcd clock on i.MXRT.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Since video_ctfb_mode_to_display_timing() has been implemented by moving
sunxi_ctfb_mode_to_display_timing() to video_modes.c and it's meant to be
used by other video subsystem, let's use it instead of local
sunxi_ctfb_mode_to_display_timing().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function converts from "struct ctf_res_modes" to
"struct display_timing".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Need to add set_parent() callback to allow dts assigned-clock-parents to
work so let's add it accordingly.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
mxsfb needs PLL5 as source, so let's setup it at its default frequency
specified in RM(650Mhz).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
"video:" must be "video", ":" is a typo.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
pllv3 PLLs have powerdown/up bits but enable bits too. Specifically
"enable bit" enable the pll output, so when dis/enabling pll by
setting/clearing power_bit we must also set/clear enable_bit.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add nfsboot wrapper to env to boot Linux kernel from TFTP/NFS.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After triggering a "reboot" command in Linux the following
hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error happens because the CMD_ERR bit is set in the IRQ status
register after booting from Linux.
To ensure a fresh start, force the VMMC supply to get unpowered first.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ethernet, usdhc2 and i2c1 interfaces are probed by dm drivers.
Therefor init functions in board file are not necessary.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
Keep code for non-dm configuration of baseboard WRU4.
It cannot be upgraded to device model as
we have no suitable device tree for it.
These changes were not run-tested on WRU4,
only compile-tested.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
The device trees for TQMa6x SOM support variations in
- CPU type: imx6dl- or imx6q-
- MBa6 I2C bus access: -mba6a (i2c1) or -mba6b (i2c3)
(plus the respective common/module include trees)
- USBH1 is directly connected to a hub
- USBOTG is connected to a separate connector
and can act as host/device or full OTG port.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
reason: SYS_TEXT_BASE was moved to Kconfig. Give reasonable defaults
in board specific Kconfig.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
The i.MX6DP and i.MX6QP incorporate NoC interconnect logic
which needs to be configured in order to use external DDR memory.
This patch enables the SPL to configure the necessary registers
in accordance with the NXP engineering bulletin EB828.
Co-developed-by: Filip Brozović <fbrozovic@gmail.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx6ulz-evk board does not have networking support, explicitly
disable networking to avoid the board removal.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
mx6ul_evk uses DM_ETH, so there is no need to have board code
to setup the FEC IOMUX and to register the network ports via the
old board_eth_init() method.
Remove these FEC related pieces of code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CONFIG_FEC_MXC is supported in Kconfig, so it is preferred to
move it to defconfig file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
LDO mode may be already enabled by the ROM and enabling it again
can cause U-Boot to hang.
Avoid this problem by only enabling LDO mode if it is initially disabled.
Reported-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
These PMC0 definitions are already defined in the beginning
of the file, so remove the duplication.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Remove invalid URLs for "Information Technology - AT Attachment-3 Interface
(ATA-3)", point to ANSI X3.298-1997.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fix documentation bug reported by 'make refcheckdocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fix some errors pointed out by 'make refcheckdocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
boards.cfg is not delivered with the U-Boot source. So it is preferable to
look at configs/*_defconfig to identify available deconfigs.
Fix a typo.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add compressed Image parsing support so that booti can parse both
flat and compressed Image to boot Linux. Currently, it is difficult
to calculate a safe address for every board where the compressed
image can be decompressed. It is also not possible to figure out the
size of the compressed file as well. Thus, user need to set two
additional environment variables kernel_comp_addr_r and filesize to
make this work.
Following compression methods are supported for now.
lzma, lzo, bzip2, gzip.
lz4 support is not added as ARM64 kernel generates a lz4 compressed
image with legacy header which U-Boot doesn't know how to parse and
decompress.
Tested on HiFive Unleashed and Qemu for RISC-V.
Tested on Qemu for ARM64.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix minor rST formatting problems]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, there is no method that can detect compression types
given a file. This is very useful where a compressed kernel image
is loaded directly to the memory.
Inspect initial few bytes to figure out compression type of the
image. It will be used in booti method for now but can be reused
any other function in future as well.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no way to select BZIP2 compression method.
Add it under library/compression config where all other
compression related configs are present.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This additional bitflip memory test is inspired by the bitflip test
in memtester v4.3.0. It show some errors on some problematic GARDENA
MT7688 based boards. The other memory tests usually don't show any
errors here.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes mtest to correctly count the overall errors and
print them even in the abort (Ctrl-C) case.
Signed-off-by: Stefan Roese <sr@denx.de>
