Some of the environment configuration in AM65x is not available in
J721e due to additions on one but not the other. These two platforms
are similar enough these common definitions should be factored out
to a common area, prepare for this by synchronizing them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT so that number of flash banks
are automatically detected by CFI flash driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add environment variables to boot kernel from a filesystem contained in
the 2nd UFS LUN. The user can boot from a ufs filesystem just by
entering the following commands.
=> setenv boot ufs
=> boot
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add support to boot some remoteprocs at U-boot prompt on the J721E EVM
boards by using the 'boot_rprocs' and other env variables defined in the
common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS'
macro.
The list of R5F cores to be started before loading and booting the Linux
kernel are as follows, and in this order:
Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7-main-r5f0_1-fw
Main R5FSS1 (LockStep) : 4 /lib/firmware/j7-main-r5f1_0-fw
The MCU R5FSS0 and Main R5FSS1 are currently in LockStep mode, so the
equivalent Core1 rprocs (rproc #1 and #5) are not included. The Main
R5FSS0 Core0 (rproc #2) is already started by R5 SPL, so is not included
in the list either.
The DSP cores are started in the following order before loading and
booting the Linux kernel:
C66_0: 6 /lib/firmware/j7-c66_0-fw
C66_1: 7 /lib/firmware/j7-c66_1-fw
C71_0: 8 /lib/firmware/j7-c71_0-fw
The order of the rprocs to boot can be changed at runtime if desired by
overwriting the 'rproc_fw_binaries' environment variable at U-boot prompt.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This converts the following to Kconfig:
CONFIG_SYS_SPI_U_BOOT_OFFS
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable 'name_overlays' serves the same purpose. Remove
'overlay_files' and use 'name_overlays' everywhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
