LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This option enable adding new platform suport just by adding defconfig
and DTS file which will target generic configuration for SoC.
Make no sense to extend Kconfig just create a pointer between DTS and
configuration file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1
Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds emulated spmi bus controller with part of
pm8916 pmic on it to sandbox and tests validating SPMI uclass.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_USB_ULPI* from headers to defconfigs for boards that use it.
Also - add CONFIG_USB where necesarry - all boards use it,
but some are not defining it explicitly.
Affected boards:
colibri_t20, harmony, mcx, mt_ventoux, twister,
zynq_(picozed, zc702, zc706, zed, zybo)
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with
the CPU complex swapped out for a quad-core ARMv8. This can operate in 32-
or 64-bit mode. 32-bit mode is the current default selected by the
VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of
U-Boot for the Raspberry Pi 3.
>From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a
change in usage of the SoC UARTs. On all previous Pis, the PL011 was the
only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a
UART to connect to the SoC. By default, the PL011 is used for this purpose
since it has larger FIFOs than the other "mini" UART. However, this can
be configured via the VideoCore firmware's config.txt file. This patch
hard-codes use of the mini UART in the RPi 3 port. If your system uses the
PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot
port instead. A future change might determine which UART to use at
run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed
together.
The mini UART has some limitations. One externally visible issue in the
BCM2837 integration is that the UART divides the SoC's "core clock" to
generate the baud rate. The core clock is typically variable, and under
control of the VideoCore firmware for thermal management reasons. If the
VC FW does modify the core clock rate, UART communication will be
corrupted since the baud rate will vary from the expected value. This was
not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To
work around this, the VideoCore firmware can be told not to modify the SoC
core clock. However, the only way this can happen and be thermally safe is
to limit the core clock to a low/minimum frequency. This leaves
performance on the table for use-cases that don't care about a UART
console. Consequently, use of the mini UART console must be explicitly
requested by entering the following line into config.txt:
enable_uart=1
A recent version of the VC firmware is required to ensure that the mini
UART is fully and correctly initialized by the VC FW; at least
firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on
core clock See: https://github.com/raspberrypi/firmware/issues/572".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.
This patch adds a defconfig and device tree chunks for it.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Cubietruck Plus uses all 3 USB controllers:
- USB OTG functions are provided by the musb USB OTG controller
- Onboard SATA is provied by a USB-SATA bridge connected to USB1
- The USB host ports on the board are provided by an HSIC USB hub
FLDO1 is set to 1.2V for HSIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The h8_homlet_v2 has 2 USB host ports, one connected to the OTG
controller, one connected to the EHCI/OHCI pair.
Also provide the card detect pin for MMC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
DLDO4 supplies power to the PD pins, and the AC200 Ethernet PHY /
composite video encoder.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The schematics of the h8_homlet_v2 show DCDC1 set to 3.3V. Some
Allwinner-based boards set it to 3.0V to conserve power. Since the
h8_homlet_v2 is a set-top box board with external power, there is
no such requirement.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
DCDC5 is designed to supply VCC-DRAM, which is normally 1.5V for DDR3,
1.35V for DDR3L, and 1.2V for LPDDR3.
Also remove CONFIG_AXP_DCDC5_VOLT from h8_homlet_v2_defconfig.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
LDO3 and LDO4 are used to power port E resp. port G, which are exposed
on gpio headers, so enable them at 2.8V as specified in the schematic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Force master mode on the A20-OLinuXino-Lime2. This change is required
to get a reliable link at gigabit speeds.
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Force master mode for 1000BASE-T operation on the
A20-Olimex-SOM-EVB.
Karsten Merker reports that this change is necessary to get a reliable
link at gigabit speeds.
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sec_init has been called at the beginning to initialize SEC Block
(CAAM) which is used by secure boot validation later for both ls2080a
qds and rdb. 64-bit address in ESBC Header has been enabled. Secure
boot defconfigs are created for boards (NOR boot).
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The description was borrowed from kernel. "tristate" type was changed
to "bool" (I believe we don't support modules for u-boot yet, right?).
CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along
as well.
Definitions were added to defconfig files in a way that
"make savedefconfig" generates exactly the same file as used defconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Add zynq_zc702 conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support for Altera StratixV bitstream programming. 2 FPGAs
are connected to the SPI busses. This patch uses board specific write
code to program the bitstream via SPI direct write mode.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.
This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Kconfig default settings are same as mentioned Sinovoip
Bpi-m3 schematic.
As axp818 ALDO support is enabled, it causes bpi-m3 fail to boot
if ALDOs are set to 0.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This enables support for the eMMC found on the orangepi plus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This fixes the USB ports not working on the orangepi_plus and stops us
from messing with gpio-s which we should not touch on the orangepi_pc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The CHIP has a composite video output in the mini-Jack connector, alongside
with the 2 audio channels. Enable this output in U-Boot.
Signed-off-by: Alex Kaplan <kaplan2539@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Unlike the datasheet recommendation, the R8 SoC requires a 1.4V supply
for its CPU when operating at 1Ghz.
Rely on the default value specified in the Kconfig entry.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
The added dts file is identical to the one submitted to the upstream
kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD,
1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The yones toptech bs1078-v2 is a 10.1" tablet without any clear markings on
the outside, but 'YONESTOPTECH-BS1078' written on the PCB silkscreen.
It features a 16:9 1024:600 LCD, A31s SoC, 1GB RAM, 8G NAND, silead gsl3675
touchscreen and a RTL8723AS wifi chip:
https://linux-sunxi.org/Yones_Toptech_BS1078_V2
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add defconfig for the multi board device based on the
Allwinner A20 SoC. It contains the A20 Itead Core module and a
base board for the external interfaces.
The core module comes with 4GB NAND and 1GB DDR RAM.
The base board to which the core board is connected provides
3 USB 2.0 Host ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet
port, HDMI, IR receiver, SPDIF and a 32-pin GPIO header. This
header expands the features of core board by exposing the VGA pins,
audio In/Out pins, SATA, SPI, I2C, UARTS, USB-OTG and power..
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.
The board also has an EEPROM on i2c0 which holds the MAC address.
DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20
is connected to the reset control of the PHY. EMAC is not actually
supported yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Difrnce dit4350 tablet is a tiny tablet with a 4.3" 16:9 480x272 LCD,
A13 SoC, 512M RAM, 4G NAND, solomon systech ssd2532qn6 touchscreen at
i2c1 address 0x48, Memsic MXC622X accelerometer at i2c1 address 0x15 and
rtl8188etv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.
The added dts is identical to the dts submitted to the upstream kernel,
note this commit also syncs axp22x.dtsi and sun6i-a31.dtsi with the
upstream kernel as the added dts depends on these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too
long. It would not hurt to drop "PH1_" because "UNIPHIER_" already
well specifies the SoC family. Also, rename files for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some boards' defconfig files are out of order. Clean this up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch makes the following changes to the SR1500 board port:
- Update defconfig to support SPI NOR (use make savedefconfig).
- Increase SPI speed to a maximum of 100MHz for faster system
bootup.
- Change environment location, so that its not between SPL and
main U-Boot. This way the combined SPL / U-Boot image can
be used for updates.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
