Commit Graph

16671 Commits

Author SHA1 Message Date
Patrick Delaunay
5e959ab85e stm32mp1: board: Update the way vdd-supply is retrieved from DT
Due to kernel DT alignment, pwr-supply is renamed to vdd-supply
and is a subnode of pwr-regulators.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 11:19:23 +02:00
Patrick Delaunay
dd2810851e stm32mp1: board: support of error led on ed1/ev1 board
Create a function led_error_blink and add node in device
tree.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 11:19:23 +02:00
Patrick Delaunay
d573e46168 stm32mp1: board: enable v1v2_hdmi and v3v3_hdmi regulator on dk2 boot
As for Audio codec IC, HDMI IC is not "IO safe".
HDMI regulators (v3v3 and v1v2) must be enabled to allow
I2C1 bus usage. HDMI IC must be under reset during power up
and keep HDMI and AUDIO devices in reset while they are not
used in U-Boot to keep them in low power mode
(each device can be kept in reset independently keeping their
power supplies ON until kernel).

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 11:19:23 +02:00
Patrick Delaunay
49ef8e134e stm32mp1: configs: add spi load support in spl
Add the boot for NOR, SPL load U-Boot.img at offset
CONFIG_SYS_SPI_U_BOOT_OFFS = 0x80000.
It is the start address of mtd partition ssbl in nor.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 11:19:23 +02:00
Patrick Delaunay
9cd8b9f0c5 stm32mp1: configs: add condition to activate WATCHDOG in SPL
Only activate WATCHDOG in SPL when CONFIG_WATCHDOG is activated in U-Boot.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
f219361de1 stm32mp1: configs: imply CONFIG_OF_LIBFDT_OVERLAY
Add imply for FDT overlay that can be usefuill for kernel device tree
management but it is not mandatory (can be removed to gain space)

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
a67d958177 stm32mp1: configs: Activate DISABLE_CONSOLE
Activate DISABLE_CONSOLE needed for stm32prog support on uart.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
16a0722320 stm32mp1: configs: select CONFIG_STM32_SERIAL
Select the serial driver mandatory for the console.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
6755198001 stm32mp1: configs: activate PRE_CONSOLE_BUFFER
Correctly handle silent=1 in the default environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
c50c928064 stm32mp1: configs: activate CONFIG_SILENT_CONSOLE
Allow to disable console with environment variable 'silent':
> env set silent 1; env save

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
178a415534 stpmic1: program pmic to keep only the debug unit on
Depending on backup register value, we maintain the debug unit
powered-on for debugging purpose.
Only BUCK1 is required for powering the debug unit, so revert
the setting for all the other power lanes, except BUCK3 that
has to be always on.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
7acda7eae5 ARM: dts: stm32mp1: add pull-up on serial rx of console connected to STLINK
Avoid U-Boot auto-boot interruption for line break detection
on console when the RX line connected to STLINK is floating
(-IO error in getc cause by framing error and testc return 1)
Same workaround is applied on all the STMicroelectonics board.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
9c2214b489 ARM: dts: stm32mp1: add key support on DK1/DK2
Allow to use PA13 and PA14 to force fastboot mode or STM32CubeProgrammer
mode.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
2c2580984a ARM: dts: stm32mp1: add ldtc pre-reloc proper in SOC file
The pre-relocation probe is needed to reserve video frame buffer
in video_reserve() for all the board;
LDTC must be tagged prereloc in SOC U-Boot dtsi file.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
67b7684f8c ARM: dts: stm32mp1: Add PSCI node access before relocation
Add node in DT and avoid error to search UCLASS_SYSRESET in
board_f.c::print_resetinfo() and lost 1.6s in U-Boot
for the trusted boot chain.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
6d923007d6 ARM: dts: stm32mp1: Add iwdg2 support for SPL
This patch adds independent watchdog support for stm32mp157c
in SPL.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
be16c41f85 ARM: dts: stm32mp1: DDR config v1.45
Update DDR configuration with the latest update:
- Change DQSGE to 1 for DDR3, to cure missing DQS preamble.

Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
fe91533644 ARM: dts: stm32mp1: sync device tree with v5.3-rc2
Synchronize device tree with v5.3-rc2 label and
update the associated u-boot dtsi.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrice Chotard
0203050e57 ARM: dts: stih410-b2260: Sync DT with kernel v5.2
Synchronize U-boot DT with kernel v5.2 for stih410-b2260.
Update stih410-b2260-u-boot.dtsi accordingly.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-08-27 09:36:56 +02:00
Tom Rini
12277acda0 Merge branch '2019-08-26-master-imports'
- Assorted minor bugfixes
2019-08-26 17:45:20 -04:00
Adam Ford
5adbc0e5ca ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node  when it should have been placed into the
omap3_pmx_core.  This error was accidentally propagated to U-Boot by
me when I blindly copied the device tree from Linux.

This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26 11:46:20 -04:00
Tom Rini
7a4b0bc5fe Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- Support SPL and OpenSBI (FW_DYNAMIC firmware) boot.
- Fix qemu kconfig build warning.
2019-08-26 09:50:46 -04:00
Lukas Auer
89fe196c99 riscv: add a generic FIT generator script
Add a generic FIT generator script for RISC-V to generate images
containing U-Boot, OpenSBI FW_DYNAMIC firmware, and optionally one or
more device trees. The location of the OpenSBI firmware binary can be
specified with the OPENSBI environment variable. By default, it is
assumed to be "fw_dynamic.bin", located in the U-Boot top-level. Device
trees are passed as arguments to the generator script. A separate
configuration entry is created for each device tree.

The load addresses of U-Boot and OpenSBI are parsed from the U-Boot
configuration. They can be overwritten with the UBOOT_LOAD_ADDR and
OPENSBI_LOAD_ADDR environment variables.

The script is based on the i.MX (arch/arm/mach-imx/mkimage_fit_atf.sh)
and Allwinner sunxi (board/sunxi/mksunxi_fit_atf.sh) FIT generator
scripts.

Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26 16:07:42 +08:00
Lukas Auer
c7e1effb96 riscv: support SPL stack and global data relocation
To support relocation of the stack and global data on RISC-V, the
secondary harts must be notified of the change using IPIs. We can reuse
the hart relocation code for this purpose. It uses global data to store
the new stack pointer and global data pointer for the secondary harts.
This means that we cannot update the global data pointer of the main
hart in spl_relocate_stack_gd(), because the secondary harts have not
yet been relocated at this point. It is updated after the secondary
harts have been notified.

Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26 16:07:42 +08:00
Lukas Auer
8c59f2023c riscv: add SPL support
U-Boot SPL on the generic RISC-V CPU supports two boot flows, directly
jumping to the image and via OpenSBI firmware. In the first case, both
U-Boot SPL and proper must be compiled to run in the same privilege
mode. Using OpenSBI firmware, U-Boot SPL must be compiled for machine
mode and U-Boot proper for supervisor mode.

To be able to use SPL, boards have to provide a supported SPL boot
device.

Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26 16:07:42 +08:00
Lukas Auer
fbfd92bf9b riscv: add run mode configuration for SPL
U-Boot SPL can be run in a different privilege mode from U-Boot proper.
Add new configuration entries for SPL to allow the run mode to be
configured independently of U-Boot proper.

Extend all uses of the CONFIG_RISCV_SMODE and CONFIG_RISCV_MMODE
configuration symbols to also cover the SPL equivalents. Ensure that
files compatible with only one privilege mode are not included in builds
targeting an incompatible privilege mode.

Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26 16:07:42 +08:00
Adam Ford
1bf330150c Convert CONFIG_ARCH_CPU_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
2019-08-25 19:32:55 -04:00
Tom Rini
50b4b80f59 Merge tag 'u-boot-rockchip-20190823' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- remove rk3288 fennec board
- remove SPL raw image support for Rockchip SoCs
- add common misc_init_r() for ethaddr from cpuid
- enable USB HOST support for rk3328
- unify code for finding a valid gpt in part driver
2019-08-24 08:33:27 -04:00
Adam Ford
057055660f Kconfigs: Various: Fix some SPL, TPL and ARM64 dependencies
Several options are presenting themselves on a various boards
where the options are clearly not used.  (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)

This patch is not attempting to be a complete list of items, but
more like low hanging fruit.

This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-23 13:59:06 -04:00
Rohan Garg
0482538499 rockchip: rk3399: derive ethaddr from cpuid
Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.

The MAC address is only generated and set if there is no ethaddr
present in the saved environment.

This is based off of Klaus Goger's work in 8adc9d

Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 18:15:31 +08:00
Kever Yang
cb8c492f20 rockchip: rk3288: remove fennec board support
Since there is no one using this board, remove it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 15:27:40 +08:00
Kever Yang
08bbe44424 rockchip: dts: rk3328-rock64: fix usb power supply
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are
controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct
power supply for USB HOST ports.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 15:27:40 +08:00
Kever Yang
2e91e2025c rockchip: rk3328: migrate u-boot node to -u-boot.dtsi
Move all the nodes only shown in u-boot to -u-boot.dtsi to make
rk3328.dtsi clean.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 15:27:40 +08:00
Kever Yang
8e5c8571fe rockchip: dts: rk3328-rock64: enable usb3 xhci controller
Rock64 has a USB3.0 port, enable the controller so that we can use it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 15:27:40 +08:00
Laurentiu Tudor
b249fcba00 armv8: ls1028a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, edma, qdma, gpu, display and sec.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Laurentiu Tudor
5c6dc6c9a9 armv8: ls1088a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Laurentiu Tudor
aef654a2ed armv8: fsl-layerscape: make icid setup endianness aware
The current implementation assumes that the registers holding the ICIDs
are universally big endian. That's no longer the case on newer
platforms so update the code to take into account the endianness of
each register.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Laurentiu Tudor
08f9bc9f43 armv8: fsl-layerscape: add base addresses for several devices
Add CCSR base addresses for ESDHC2, EDMA QDMA, DISPLAY and GPU devices.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Laurentiu Tudor
ef3f364a75 armv8: fsl-layerscape: add missing sec jr base address defines
Add defines for all the SEC job rings base addresses.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
71a2da3fa9 armv8: kconfig: Fix some platforms incorrect I2C clock divider
By default, i2c input clock is platform clk / 2, but some of the
platform of i2c clock divider does not meet this kind of circumstance,
so alone to set default values for these platforms.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Pankaj Bansal
a02a9421f4 armv8: ls1028aqds: define ARCH_MISC_INIT to handle mux
Define ARCH_MISC_INIT for LS1028AQDS platform to handle board
related mux.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
67d3a815cb configs: ls1088a: Enable DM support for pcf2127 rtc
Enable related configs on all ls1088aqds boards to support pcf2127
rtc DM function.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
f3b6a711a4 armv8: dts: ls1088aqds : Add pcf2127 node
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
96d3fb4146 armv8: dts: ls1088ardb: Add slave nodes under the i2c0 controller
This patch adds some slave nodes to support the i2c dm on the device
side under the i2c0 controller.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
c2eda95a5b armv8: dts: ls1088a: add I2C node support
One ls1088a, there are four I2C controllers. So add all I2C node
for ls1088a in device tree.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
bd9eab46c8 gpio: do not include <asm/arch/gpio.h> on ARCH_LS1088A
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1088a.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
292370df1c configs: ls2088a: Enable DM support for ds3231 rtc
Enable related configs on all ls2088aqds boards to support ds3231
rtc DM function.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
1703aaff8b armv8: dts: ls2088aqds : Add ds3232 node
Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds
boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
6672ab1628 armv8: dts: ls2088ardb: Add slave nodes under the i2c0
Add some slave nodes to support the i2c dm on the device side under the i2c0.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
chuanhua han
407916f5d7 armv8: dts: fsl-ls2088a: add i2c node support
One ls2088a, there are four I2C controllers. So add I2C nodes in dts
for ls2088a.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30