The board is able to boot from the following source:
- user-updateble SPI flash
- write-protected part of the same SPI flash
- eMMC
- SD card
Implement the needed function hooks to support all of these boot
sources.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
By default the OCRAM is marked as secure. While the SPL runs in EL3 and
thus can access it, DMA devices cannot. Mark the whole OCRAM as
non-secure.
This will fix MMC and SD card boot on LS1028A when using SPL instead of
TF-A.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This adds the onkey, RTC and watchdog children to the DA9063 PMIC node,
fixes the compatible for qspi0's flash node to match the official DT
schema (it being an is25wp256 is discoverable, hence jedec,spi-nor is
the only compatible that should be present) and exposes the card detect
GPIO.
Note that the device trees still diverge in some places (including
important things like the PCIe controller's clock name) and should be
cleaned up so that a common device tree is used in both projects rather
than having different bindings. This patch does not attempt to do that,
merely expose important functionality present in Linux's that is not in
U-Boot's so that it can be used without the OS providing its own bundled
copy.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Adding some debug prints I can see:
MMC: mmc@fe320000: Got clock clock-controller@ff760000 76
mmc@fe310000: Got clock clock-controller@ff760000 77
Unknown clock 77
rockchip_dwmmc_get_mmc_clk: err=-2
mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0
According to kernel code the SDIO clock is identical to SDMMC clock
except for the con 16->15 change.
Add support for the clock to avoid the error.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This new image is similar to u-boot-rockchip.bin except that it's
destined to be flashed on SPI-NOR flashes.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prepares for the creation of a u-boot-rockchip-spi.bin image
similar to u-boot-rockchip.bin to the exception it's destined for
SPI-NOR flashes instead of MMC storage medium.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
By factoring SPL check in the first condition, this makes the checks a
bit less convoluted and more readable.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows to build u-boot-rockchip.bin binary with binman for Rockchip
ARM64 boards instead of the legacy Makefile way.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
idbloader.img content - currently created by way of Makefile - can be
created by binman directly.
So let's do that for Rockchip ARM platforms.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Binman mkimage entry generates temporary files so let's remove them
when calling `make clean`.
Fixes: 9b312e26fc ("rockchip: Enable building a SPI ROM image on jerry")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reported-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
mkimage entry currently creates a file whose name is derived from the
section name containing said entry.
Let's allow the user to define a filename for the mkimage-generated
binary by using the 'filename' DT property.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some image types handled by mkimage require the datafiles to be passed
independently (-d data1:data2) for specific handling of each. A
concatenation of datafiles prior to passing them to mkimage wouldn't
work.
That is the case for rkspi for example which requires page alignment
and only writing 2KB every 4KB.
This adds the ability to tell binman to pass the datafiles without
prior concatenation to mkimage, by adding the multiple-data-files
boolean property to the mkimage node.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While technically not a bug, let's have some consistency in paths
returned by u-boot,spl-boot-order look-up and the one saved in
u-boot,spl-boot-device by syncing spl_boot_devices_tbl and boot_devices
node paths.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On RK3399, mmc0 is eMMC and mmc1 is SD card, c.f. console:
MMC: mmc@fe320000: 1, mmc@fe330000: 0
In arch/arm/mach-rockchip/spl-boot-order.c:board_boot_order, the
boot_device (BOOT_DEVICE_*) value is gotten from spl_node_to_boot_device
function. Said function returns BOOT_DEVICE_MMC1 for mmc0 (eMMC) and
BOOT_DEVICE_MMC2 for mmc1 (SD card).
Since the SD card controller is at mmc@fe320000, it should be associated
with BOOT_DEVICE_MMC2 and not BOOT_DEVICE_MMC1. Same applies to eMMC.
Let's fix that by swapping the two BOOT_DEVICEs.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Rockchip SoCs need the boot_devices array defined in order to map the
bootloader's value to a U-Boot device. Implement this for rk3308.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 6aa4fe3912 ("dm: core: Rename and fix uclass_get_by_name_len()")
changed uclass_get_device_by_name() to an exact match when previously it
behaved as a prefix match.
The roc-cc code relied on this prefix match by only specifying part of
the device name. Fix this by using the full name including the address.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When idbloader.img is flashed on the eMMC, the SPL still tries to load
from SPI-NOR first.
This is due to an incorrect look-up in the Device Tree. Since commit
822556a934 ("arm: dts: sync the Rockhip 3399 SoCs from Linux"), the
node name (but not label) changed from sdhci@fe330000 to mmc@fe330000
meaning U-Boot SPL is not looking for the correct node name anymore and
fails to find the "same-as-spl" node when eMMC is the medium from which
the SPL booted.
Fixes: 822556a934 ("arm: dts: sync the Rockhip 3399 SoCs from Linux")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Lapkin Artem <email2tema@gmail.com>
Tested-by: Lapkin Artem <email2tema@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the default initialisation frequency is 50MHz. Although
this does appear to be suitable for some LPDDR4 RAM chips, training at
this low frequency has been seen to cause Column errors, leading to
Capacity check errors on others.
Here we force RAM initialisation to happen at 400MHz before ramping up
to the final value running value of 800MHz after everything has been
successfully configured.
Link: https://lore.kernel.org/u-boot/Yo4v3jUeHXTovjOH@google.com/
Suggested-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Frequency changes to 400MHz are presently reported as:
lpddr4_set_rate_0: change freq to 400000000 mhz 0, 1
This is obviously wrong by 6 orders of magnitude.
Ensure frequency changes are reported accurately.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Functions pointed to by this op pointer can return non-zero values
indicating an error. Ensure any error value is propagated back up the
call-chain.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Only add the dram channel when we finally setup it successfully at the
last step.
Signed-off-by: Han Pengfei <pengphei@foxmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot_devices constants for rk3288 were changed to match the
binding, but the dtsi file was not synced.
Fix by renaming the rk3288 mmc node names.
Also correct the clock name for "ciu-drive".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add an option to tell the TPM to commit non-volatile data immediately it
is changed, rather than waiting until later. This is needed in some
situations, since if the device reboots it may not write the data.
Add definitions for the rest of the Cr50 commands while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a vendor-specific TPM2 command for this and implement it for Cr50.
Note: This is not part of the TPM spec, but is a Cr50 extension.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is useful to read information about the current TPM state, where
supported, e.g. for debugging purposes when verified boot fails.
Add support for this to the TPM interface as well as Cr50. Add a simple
sandbox test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present the emulator assumes that the TPM is inited in the same phase
where it is used. But in fact SPL may init the TPM, so we don't want to
complain when U-Boot proper later uses it. Remove this check.
It might be best to save this information into the device state for the
TPM, so that we can make sure the TPM was inited at some point. For now,
this seems good enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The message format is incorrect. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The offset here is incorrect. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This feature is used for measured boot, so we can add a log entry to the
TCPA with some information about where the digest comes from. It is not
currently supported in the TPM drivers, but add it to the API so that
code which expects it can signal its request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
UEFI specification 2.9A requires to display the EUI-64 "in hexadecimal
format with byte 7 first (i.e., on the left) and byte 0 last".
This is in contrast to what the NVMe specification wants.
But it is what EDK II has been implementing.
Here is an example with the patch applied:
qemu-system-aarch64 -machine virt -cpu cortex-a72 -nographic \
-bios denx/u-boot.bin \
-device nvme,id=nvme1,serial=9ff81223 \
-device nvme-ns,bus=nvme1,drive=nvme1n0,eui64=0x123456789ABCDEF0 \
-drive file=arm64.img,if=none,format=raw,id=nvme1n0
=> nvme scan
=> efidebug devices
Device Path
====================
/VenHw(…)/NVMe(0x1,f0-de-bc-9a-78-56-34-12)
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Display the EBBRv2.0 conformance in the ECPT table.
The EBBRv2.0 conformance profile is set in the ECPT if
CONFIG_EFI_EBBR_2_0_CONFORMANCE=y.
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Add dependencies for CONFIG_EFI_EBBR_2_0_CONFORMANCE.
Enable the setting by default.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The ECPT table will be included in the UEFI specification 2.9+.
The ECPT table was introduced in UEFI following the code-first path. The
acceptance ticket can be viewed at:
https://bugzilla.tianocore.org/show_bug.cgi?id=3591
The Conformance Profiles table is a UEFI configuration table that contains
GUID of the UEFI profiles that the UEFI implementation conforms with.
The ECPT table is created when CONFIG_EFI_ECPT=y.
The config is set by default.
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The selftest checking the handling of exceptions in UEFI binaries is using
assembly to provide an undefined instruction. On the sandbox the correct
form of the instruction depends on the host architecture.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In the extended text input protocol support input of control letters
0x1c - 0x1f.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We cannot expect the buffers passed to the input protocols to be zero
filled. If only modifier keys are pressed, we have to return EFI_NOT_READY
but we still have to fill the key structure.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We need to support multiple digits in the parts of the UEFI verision
number. E.g.
EFI_SPECIFICATION_VERSION = (123 << 16) | 456
must be printed as
123.45.6
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The host will report such error message if the fastboot device work in
full-speed mode: "Duplicate descriptor for config 1 interface 0
altsetting 0, skipping"
Fastboot device ack both full and high speed interface descriptors when
work in full-speed mode, that's will cause this issue.
Fix it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: John Keeping <john@metanate.com>
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As the Renesas Reduced Pin Count Interface may be locked by TF-A, it is
disabled by default[1]. When unlocked, TF-A passes a DT fragment to
enable it, which is applied to the U-Boot DT[2].
Unlike the memory layout, the RPC-IF enablement is not propagated to
subsequent software. Hence e.g. Linux cannot know if the RPC-IF is
locked or not, and will lock-up when trying to access the RPC-IF when
locked.
Fix this by checking if the RPC-IF is enabled in the TF-A DT fragment, and
setting the status of the RPC-IF device node in the target DT, if
present, to "okay". Do this only when a "flash" subnode is found, to
avoid errors in subsequent software when the RPC-IF is not intended to
be used.
Note that this requires the status of the RPC-IF node to be set to
"disabled" in the target DT, just like in the U-Boot DT.
[1] commit 3d5f45c95c ("ARM: dts: rmobile: Disable RPC HF by
default")
[2] commit 361377dbdb ("ARM: rmobile: Merge prior-stage firmware
DT fragment into U-Boot DT on Gen3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the Generic Names Recommendation in the Devicetree
Specification Release v0.3, and the DT Bindings for the Renesas Reduced
Pin Count Interface, the node name for a Renesas RPC-IF device should be
"spi". Especially on R-Car Gen3 and RZ/G2, the node name matters, as
the node is enabled by passing a DT fragment from TF-A to U-Boot, and
from U-Boot to subsequent software.
Fix this by renaming the device nodes from "rpc" to "spi".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Upstream bzip2 1.0.x actually is stuck when running bzip2 -V and
redirecting the output. This is fixed in Debian for about a decade
already in
https://git.launchpad.net/ubuntu/+source/bzip2/tree/debian/patches/20-legacy.patch?h=ubuntu/jammy
and in bzip2 1.1.x (no release yet, see
65179284ce
).
Fedora notably does not have such a patch.
Since bzip2 --help actually prints the version number too, let's use it
instead so that binman works fine on (hopefully) all distributions.
Fixes: 45aa279800 ("binman: Add bzip2 bintool")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bintool.version can now be passed the binary argument to return the
version text, so there's no need to override it in futility anymore.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
