With of-platdata we always have a dtv struct that holds the platform data
provided by the driver_info record. However, this struct can be empty if
there are no actual devicetree properties provided.
The upshot of empty platform data is that it will end up as a zero-size
member in the BSS section, which is fine. But if the driver specifies
plat_auto then it expects the correct amount of space to be allocated.
At present this does not happen, since device_bind() assumes that the
platform-data size will always be >0. As a result we end up not
allocating the space and just use the BSS region, overwriting whatever
other contents are present.
Fix this by removing the condition that platform data be non-empty, always
allocating space if requested.
This fixes a strange bug that has been lurking since of-platdata was
implemented. It has likely never been noticed since devices normally have
at least some devicetree properties, BSS is seldom used on SPL, the dtv
structs are normally at the end of bss and the overwriting only happens
if a driver changes its platform data.
It was discovered using sandbox_spl, which exercises more features than
a normal board might, and the critical global_data variable 'gd' happened
to be at the end of BSS.
Fixes: 9fa2819009 ("dm: core: Expand platdata for of-platdata devices")
Signed-off-by: Simon Glass <sjg@chromium.org>
All debug messages from ep0.c except a few are printed by dbg_ep0() macro.
So for remaining few exceptions use also dbg_ep0() instead of serial_printf().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If we do not set FIFO buffer address and size for some endpoint which is in
use then default programmed address 0x0 would be used which is in conflict
with address of FIFO buffer for endpoint 0. Moreover address of FIFO buffer
for endpoint 0 cannot be programmed, it is fixed to 0x0. Sharing address
space between more endpoints cause data loss and unexpected errors.
This patch is fixing transmission of characters over usbtty serial console
and allows using of usbtty for debugging purposes on Nokia N900.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Interrupt for EP0 is indicated in intrtx register via first bit. This bit
is set for both RX and TX despite register has only TX in its name. First
bit in intrrx register is reserved, not used and never set.
So remove calling musb_peri_ep0() function at every iteration of udc_irq()
and musb_peri_rx() and call it only from musb_peri_tx() when correct
interrupt bit in initrtx it set.
Address from SET ADDRESS command must be set to faddr register only after
acknowledging SERV_RXPKTRDY followed by received EP0 interrupt. So prior
calling musb_peri_ep0_set_address() check for EP0 interrupt instead of
(incorrect) MUSB_INTR_SOF interrupt.
This patch fixes issue that host (computer) cannot register U-Boot USB
device and is failing with errors:
usb 1-1: new full-speed USB device number 86 using xhci_hcd
usb 1-1: Device not responding to setup address.
usb 1-1: Device not responding to setup address.
usb 1-1: device not accepting address 86, error -71
U-Boot was writing address to faddr register too early and did not wait for
correct interrupt after which should update address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If musb_peri_rx_ep() was called to process received HW buffer but U-Boot
cannot read it yet (e.g. because U-Boot SW buffer is full) then interrupt
was marked as processed also when HW buffer stayed unprocessed.
U-Boot tried to process this buffer again when it received interrupt again,
but it can receive it only when sender (host) sends a new data. As sender
(host) is not going to send a new data until U-Boot process current data
this issue caused a deadlock in case sender (host) is emitting data faster
than U-Boot can process it.
Reading musb intrrx register automatically clears this register and marks
interrupt as processed. So to prevent marking interrupt in U-Boot as
processed, adds a new variable pending_intrrx which would contain
unprocessed bits of intrrx register.
For a second step, every time when musb_peri_rx_ep() is called and there
are waiting data to be processed (signaled by MUSB_RXCSR_RXPKTRDY) either
acknowledge sender (via musb_peri_rx_ack()) that whole HW buffer was
processed or set corresponding bit in pending_intrrx that HW buffer was not
fully processed yet and next iteration is required after U-Boot allocates
space for reading HW buffer.
This patch fixes receiving large usb buffers, e.g. file transfer via Kermit
protocol implemented by 'loadb' U-Boot command over usbtty serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If udc_endpoint_write() was called with bigger payload which does not fit
into one USB packet it is needed to transmit payload in more USB packets.
First packet is transmitted by udc_endpoint_write() call itself and other
packets are put into waiting queue.
Implement function musb_peri_tx() which checks if endpoints are ready for
transmit and continue transmission of waiting queue.
This patch fixes sending big output from printenv command over usbtty
serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>>
PERI_RXCSR is 16bit register so store its value into 16bit local variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
This patch fixes configuring FIFOs for one-directional endpoints which have
only one queue (either RX or TX, but noth both).
Size of FIFO buffer is 2^(idx+3) bytes and starting address is 2^(addr+3).
Moreover first 64 bytes are reserved for EP0.
Without this patch if FIFO size specified by caller was zero then idx was
incorrectly calculated (expr. ffs(0)-1) and size overflowed in fifosz
register. This register uses has only 4 bits for FIFO size. Moreover
specifying zero buffer size is not possible (with idx=0 is minimal buffer
size 8 bytes).
So even for one-directional endpoints we need to correctly specify both
(RX and TX) FIFO buffer sizes and its addresses.
This patch is fixing calculation of start address and buffer size to
minimal value and ensures that it would not overlap with buffer reserved
for EP0.
This issue caused loose of packets on USB bus in both directions and
basically usbtty was unusable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Without this patch clearing was done only when U-Boot was compiled with
MUSB Host Controller. But clearing of data toggle bit is needed also for
MUSB Device Controller otherwise Device Controller does not work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Function next_urb() selects the last urb data buffer from linked list to
which next data from usbtty's puts function should be appended.
But to check if TX data still exists it is needed to look at the first urb
data buffer from linked list. So check for endpoint->tx_urb (first from the
linked list) instead of current_urb (the last from the linked list).
Successful call to udc_endpoint_write() may invalidate active urb and
allocate new urb in queue which invalidates pointer returned by next_urb()
function.
So call next_urb() prior putting data into urb buffer and call it every
time after using udc_endpoint_write() function to prevent sending data from
usbtty's puts function in incorrect order.
This patch fixes issue that usbtty code does not transmit data when they
are waiting in the tx queue.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
This function has incorrect implementation of prepending CR prior LF.
Without this patch it prepended CR prior whole string which is going to be
written and let LF without leading CR. Fix this issue by inserting CR at
correct place to make output on usbtty serial console more readable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
On the RPi4 armv7 build we have the situationt that we use physical
addresses of 64 bit, while the virtual addresses are 32 bit.
Remap the base address in this scenario via map_physmem().
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add tuning functionality which is needed for HS200 mode.
For HS200, program the correct needed 1.8 voltage
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
On imx6Q/imx6DL, we find if config the DTOCV to 0~3, it will impact
cmd6 behavior, after cmd6 get transfer complete interrupt, the data0
line will keep low over 5 seconds. This should be a IC bug on imx6Q/DL.
For other platforms, do not has this issue.
To fix this issue, fix the DTOCV to 0xE, the max setting, this also align
with Linux configuration.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a compatible for i.MX51 so that i.MX51 can use this driver
via driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Set default critical/alert temperature and enabling monoitoring.
Without calling imx_tmu_enable_msite() monitoring will not be enabled
and read_temperature will return 0. Additionally without setting alert
temperature will cause imx_tmu_get_temp() to spin indefiniately thinking
the system needs to cool.
This resolves the board spinning endlessly when enabling IMX_TMU in the
SPL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since commit 8745b9ebcc ("usb: gadget: add super speed support")
ums was no more functional on platform which use dwc2_udc_otg driver.
This was due to a too restrictive test which checked that the gadget
driver speed was either FS or HS.
So all gadget driver with max speed set to speed higher than
HS (SS in case of composite gadget driver in our case) are not
allowed, which is wrong.
Update the speed test in usb_gadget_register_driver() and in
dwc2_gadget_start() to allow all gadget driver speed equal or higher
than FS.
Tested on stm32mp157c-ev1 board.
Fixes: c791c8431c ("usb: dwc2: convert driver to DM_USB_GADGET")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This adds support for partitions of the form "dev.hwpart:part" and
"dev#partname". This allows one to flash to eMMC boot partitions without
having to use CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT. It also allows one to
flash to an entire device without needing CONFIG_FASTBOOT_MMC_USER_NAME.
Lastly, one can also flash MMC devices other than
CONFIG_FASTBOOT_FLASH_MMC_DEV.
Because devices can be specified explicitly, CONFIG_FASTBOOT_FLASH_MMC_DEV
is used only when necessary for existing functionality. For those cases,
fastboot_mmc_get_dev has been added as a helper function. This allows
There should be no conflicts with the existing system, but just in case, I
have ordered detection of these names after all existing names.
The fastboot_mmc_part test has been updated for these new names.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the next commit more readable by doing the move now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The only thing mmcpart was used for was to pass to blk_dselect_hwpart.
This calls blk_dselect_hwpart directly from raw_part_get_info_by_name. The
error handling is dropped, but it is reintroduced in the next commit
(albeit less specificly).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support writing to the sandbox mmc backed by an in-memory
buffer. The unit test has been updated to test reading, writing, and
erasing. I'm not sure what MMCs erase to; I picked 0, but if it's 0xFF
then that can be easily changed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.
As the overlaps are huge, variable names have been generalized
accordingly.
Apart form the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.
New hardware features are not supported, namely:
- Power on reset
- Unique ID
- Double transfer rate (DTR)
- Parameter page
- Random data quad IO
The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.
The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.
Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The datasheet only lists one dummy byte in the 0xEB operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Reto Schneider:
- Linux patch ported to U-Boot
- Checked for compatibility with GD5F1GQ4xBxxG
- Fixed operation code in original commit message (0xEH -> 0xEB)
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
On the i.MX8M Mini, ret = clk_set_rate() sets ret to the value of the
rate the clock was able to set. When checking for errors, it only
checks that it is not NULL. Since positive numbers are not errors,
only check for negative numbers when handling errors.
Fixes: 383fded70c ("spi: nxp_fspi: new driver for the FlexSPI controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The code was processed with unifdef utility to omit portions not
relevant to A38x and DDR3. This removes usage of many macros, including
A70X0, A80X0 and A3900. It seems that the unifdef utility did not remove
the macros from #else comment.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Bump version of a38x DDR3 trianing to version 14.0.0 to reflect the
version in the mv-ddr-devel branch of upstream repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
There is a new version numbering system, where after 18.12.0 came
1.0.0, 2.0.0, and so on until 14.0.0. So 14.0.0 is newer than 18.12.0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 56db5d1464b44df10a02b99e615ebd6f6a35c428 upstream.
@pali suggested this change
In commit 6285efb ("mv_ddr: add support for twin-die combined memory
device") was added support for twin-die combined memory device and
default value for explicitly uninitialized structure members is zero, s
also twin_die_combined is initialized to zero. Which means COMBINED
value.
As prior this commit there was no support for twin-die combined memory
device, default value for twin_die_combined should be NOT_COMBINED. This
change change order of enum mv_ddr_twin_die to ensure that NOT_COMBINED
has value zero.
Signed-off-by: heaterC <airyguy@gmx.de>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2bdd12dd68b1f8e27a03a3443ae49a09a14c18e4 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes code in ddr3_training.c.
Import this change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit c8b301463d508c807a33f7b7eaea98bbda4aa35e upstream.
The funtion returnd cs size in byte instead of MB, that cause
calculation error since the caller was expected to get u32 and when he
got above 4G it refers it as 0.
The fix was to get the cs memory size from function as in MB and then
multiply it by 1MB.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit d653b305d0b3da9727c49124683f1a6d95d5c9a5 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 20c89a28548cdab11f88d2ec8936344af0686a1e upstream.
WL phase correcion stage is failing while using bus_width of 16bit, not
to be fix this stage is un-necessary when working with bus_width of 16
bit.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream.
the twin-die combined memory device should be treatened as X8
device and not as X16 one
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
all boards, as this was default behaviour prior this change ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2d3b9437cf38c06c4330e0de07f29476197f5e04 upstream.
The ODT enable heuristic based on active chip-selects is not always
correct. Some board might use two chip-selects, but have only one ODT
line connected. Allow board specific mv_ddr_topology_map to directly set
the ODT configuration register value.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 3908e20c6c520339e9bddb566823ae5e065d5218 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ab9240402a70cc02496683971779e75eff410ab4 upstream.
- function mv_ddr_spd_die_capacity_user_get() has a bug,
since it insert a user memory enum to it,
instead of SPD memory enum (which are different)
- fix: remove mv_ddr_spd_die_capacity_user_get() function.
- memory size with 64 and 32 bit already calculated correctly
at mv_ddr_mem_sz_per_cs_get() function
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Stefan Chulski <Stefan.Chulski@cavium.com>
Reviewed-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6c705ebc0d70f67ed7cae83ad1978c3305ef25be upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header mv_ddr_topology.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 61a8910998d7b553e80f600ebe8147a8b98f0945 upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 32800667b375ebd1f82120da0f3479b1cf52d96d upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit a165037ec26f301be75e1fabc263643683e85255 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ce62bef8fac559e27245259882e45f19cdc293ad upstream.
- fix JIRA A7K8K-5056
- remove TEST_PATTERN write at the load patern stage earlier to WL SUP stage
- the WL SUP stage already writes this pattern to the memory, if the pattern exist at the memory
then the algorithm will fail, since it think that there are no phase to correct
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
