These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Introduced in 45b4773 (net/arp: account for ARP delay, avoid duplicate packets on timeout)
Check the arp timeout and adjust the timeout start time before the call
to eth_recv() so that the sandbox driver has the opportunity to adjust
the sandbox timer after the new start time has been recorded.
Also, change the adjustment amount by 11 seconds instead of exactly the
10 seconds that the ping timout is expecting since the timeout check is
looking for the time elapsed to be greater than but not equal to the
specified delay.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Simon Glass <sjg@chromium.org>
Some devices can take a long time to work out whether they have a new packet
or now. For example the ASIX USB Ethernet dongle can take 5 seconds to do
this, since it waits until it gets a new packet on the wire before allowing
the USB bulk read packet to be submitted.
At present with driver mode the Ethernet receive code reads 32 packets. This
can take a very long time if we must wait for all 32 packets. The old code
(before driver model) worked by reading a single set of packets from the USB
device, then processing all the packets with in. It would be nice to use
the same behaviour with driver model.
Add a flag to the receive method which indicates that the driver should try
to find a packet if available, by consulting the hardware. When the flag is
not set, it should just return any packet data it has already received. If
there is none, it should return -EAGAIN so that the loop will terminate.
Signed-off-by: Simon Glass <sjg@chromium.org>
When called, the next call to receive will trigger a 10-second leap
forward in time to avoid waiting for time to pass when tests are
evaluating timeout behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is needed to test the netretry functionality (make the command fail
on a sandbox eth device).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox driver will now generate response traffic to exercise the
ping command even when no network exists. This allows the basic data
pathways of the DM to be tested.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
