sandbox: spi: Add new SPI flash driver
This adds a SPI flash driver which simulates SPI flash clients. Currently supports the bare min that U-Boot requires: you can probe, read, erase, and write. Should be easy to extend to make it behave more exactly like a real SPI flash, but this is good enough to merge now. sjg@chromium.org added a README and tidied up code a little. Added a required map_sysmem() for sandbox. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is contained in:
Mike Frysinger
Simon Glass
parent
6122813fa2
commit
ffdb20bea1
@ -31,6 +31,60 @@ the console. It does not set the terminal into raw mode, so cursor keys and
|
||||
history will not work yet.
|
||||
|
||||
|
||||
SPI Emulation
|
||||
-------------
|
||||
|
||||
Sandbox supports SPI and SPI flash emulation.
|
||||
|
||||
This is controlled by the spi_sf argument, the format of which is:
|
||||
|
||||
bus:cs:device:file
|
||||
|
||||
bus - SPI bus number
|
||||
cs - SPI chip select number
|
||||
device - SPI device emulation name
|
||||
file - File on disk containing the data
|
||||
|
||||
For example:
|
||||
|
||||
dd if=/dev/zero of=spi.bin bs=1M count=4
|
||||
./u-boot --spi_sf 0:0:M25P16:spi.bin
|
||||
|
||||
With this setup you can issue SPI flash commands as normal:
|
||||
|
||||
=>sf probe
|
||||
SF: Detected M25P16 with page size 64 KiB, total 2 MiB
|
||||
=>sf read 0 0 10000
|
||||
SF: 65536 bytes @ 0x0 Read: OK
|
||||
=>
|
||||
|
||||
Since this is a full SPI emulation (rather than just flash), you can
|
||||
also use low-level SPI commands:
|
||||
|
||||
=>sspi 0:0 32 9f
|
||||
FF202015
|
||||
|
||||
This is issuing a READ_ID command and getting back 20 (ST Micro) part
|
||||
0x2015 (the M25P16).
|
||||
|
||||
Drivers are connected to a particular bus/cs using sandbox's state
|
||||
structure (see the 'spi' member). A set of operations must be provided
|
||||
for each driver.
|
||||
|
||||
|
||||
Configuration settings for the curious are:
|
||||
|
||||
CONFIG_SANDBOX_SPI_MAX_BUS
|
||||
The maximum number of SPI buses supported by the driver (default 1).
|
||||
|
||||
CONFIG_SANDBOX_SPI_MAX_CS
|
||||
The maximum number of chip selects supported by the driver
|
||||
(default 10).
|
||||
|
||||
CONFIG_SPI_IDLE_VAL
|
||||
The idle value on the SPI bus
|
||||
|
||||
|
||||
Tests
|
||||
-----
|
||||
|
||||
|
||||
64
doc/SPI/README.sandbox-spi
Normal file
64
doc/SPI/README.sandbox-spi
Normal file
@ -0,0 +1,64 @@
|
||||
Sandbox SPI/SPI Flash Implementation
|
||||
====================================
|
||||
|
||||
U-Boot supports SPI and SPI flash emuation in sandbox. This must be enabled
|
||||
using the --spi_sf paramter when starting U-Boot.
|
||||
|
||||
For example:
|
||||
|
||||
$ make O=sandbox sandbox_config
|
||||
$ make O=sandbox
|
||||
$ ./sandbox/u-boot --spi_sf 0:0:W25Q128:b/chromeos_peach/out/image.bin
|
||||
|
||||
The four parameters to spi_sf are:
|
||||
|
||||
SPI bus number (typically 0)
|
||||
SPI chip select number (typically 0)
|
||||
SPI chip to emulate
|
||||
File containing emulated data
|
||||
|
||||
Supported chips are W25Q16 (2MB), W25Q32 (4MB) and W25Q128 (16MB). Once
|
||||
U-Boot it started you can use 'sf' commands as normal. For example:
|
||||
|
||||
$ ./b/sandbox/u-boot --spi_sf 0:0:W25Q128:b/chromeos_peach/out/image.bin \
|
||||
-c "sf probe; sf test 0 100000; sf read 0 1000 1000; \
|
||||
sf erase 1000 1000; sf write 0 1000 1000"
|
||||
|
||||
|
||||
U-Boot 2013.10-00237-gd4e0fdb (Nov 07 2013 - 20:08:15)
|
||||
|
||||
DRAM: 128 MiB
|
||||
Using default environment
|
||||
|
||||
In: serial
|
||||
Out: serial
|
||||
Err: serial
|
||||
SF: Detected W25Q128BV with page size 256 Bytes, erase size 4 KiB, total 16 MiB
|
||||
SPI flash test:
|
||||
0 erase: 1 ticks, 1024000 KiB/s 8192.000 Mbps
|
||||
1 check: 2 ticks, 512000 KiB/s 4096.000 Mbps
|
||||
2 write: 6 ticks, 170666 KiB/s 1365.328 Mbps
|
||||
3 read: 0 ticks, 1048576000 KiB/s -201326.-592 Mbps
|
||||
Test passed
|
||||
0 erase: 1 ticks, 1024000 KiB/s 8192.000 Mbps
|
||||
1 check: 2 ticks, 512000 KiB/s 4096.000 Mbps
|
||||
2 write: 6 ticks, 170666 KiB/s 1365.328 Mbps
|
||||
3 read: 0 ticks, 1048576000 KiB/s -201326.-592 Mbps
|
||||
SF: 4096 bytes @ 0x1000 Read: OK
|
||||
SF: 4096 bytes @ 0x1000 Erased: OK
|
||||
SF: 4096 bytes @ 0x1000 Written: OK
|
||||
|
||||
|
||||
Since the SPI bus is fully implemented as well as the SPI flash connected to
|
||||
it, you can also use low-level SPI commands to access the flash. For example
|
||||
this reads the device ID from the emulated chip:
|
||||
|
||||
=> sspi 0 32 9f
|
||||
FFEF4018
|
||||
|
||||
|
||||
Simon Glass
|
||||
sjg@chromium.org
|
||||
7/11/2013
|
||||
Note that the sandbox SPI implementation was written by Mike Frysinger
|
||||
<vapier@gentoo.org>.
|
||||
@ -13,4 +13,5 @@ endif
|
||||
obj-$(CONFIG_CMD_SF) += sf.o
|
||||
obj-$(CONFIG_SPI_FLASH) += sf_probe.o sf_ops.o
|
||||
obj-$(CONFIG_SPI_FRAM_RAMTRON) += ramtron.o
|
||||
obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o
|
||||
obj-$(CONFIG_SPI_M95XXX) += eeprom_m95xxx.o
|
||||
|
||||
483
drivers/mtd/spi/sandbox.c
Normal file
483
drivers/mtd/spi/sandbox.c
Normal file
@ -0,0 +1,483 @@
|
||||
/*
|
||||
* Simulate a SPI flash
|
||||
*
|
||||
* Copyright (c) 2011-2013 The Chromium OS Authors.
|
||||
* See file CREDITS for list of people who contributed to this
|
||||
* project.
|
||||
*
|
||||
* Licensed under the GPL-2 or later.
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <malloc.h>
|
||||
#include <spi.h>
|
||||
#include <os.h>
|
||||
|
||||
#include <spi_flash.h>
|
||||
#include "sf_internal.h"
|
||||
|
||||
#include <asm/getopt.h>
|
||||
#include <asm/spi.h>
|
||||
#include <asm/state.h>
|
||||
|
||||
/*
|
||||
* The different states that our SPI flash transitions between.
|
||||
* We need to keep track of this across multiple xfer calls since
|
||||
* the SPI bus could possibly call down into us multiple times.
|
||||
*/
|
||||
enum sandbox_sf_state {
|
||||
SF_CMD, /* default state -- we're awaiting a command */
|
||||
SF_ID, /* read the flash's (jedec) ID code */
|
||||
SF_ADDR, /* processing the offset in the flash to read/etc... */
|
||||
SF_READ, /* reading data from the flash */
|
||||
SF_WRITE, /* writing data to the flash, i.e. page programming */
|
||||
SF_ERASE, /* erase the flash */
|
||||
SF_READ_STATUS, /* read the flash's status register */
|
||||
SF_READ_STATUS1, /* read the flash's status register upper 8 bits*/
|
||||
};
|
||||
|
||||
static const char *sandbox_sf_state_name(enum sandbox_sf_state state)
|
||||
{
|
||||
static const char * const states[] = {
|
||||
"CMD", "ID", "ADDR", "READ", "WRITE", "ERASE", "READ_STATUS",
|
||||
};
|
||||
return states[state];
|
||||
}
|
||||
|
||||
/* Bits for the status register */
|
||||
#define STAT_WIP (1 << 0)
|
||||
#define STAT_WEL (1 << 1)
|
||||
|
||||
/* Assume all SPI flashes have 3 byte addresses since they do atm */
|
||||
#define SF_ADDR_LEN 3
|
||||
|
||||
struct sandbox_spi_flash_erase_commands {
|
||||
u8 cmd;
|
||||
u32 size;
|
||||
};
|
||||
#define IDCODE_LEN 5
|
||||
#define MAX_ERASE_CMDS 3
|
||||
struct sandbox_spi_flash_data {
|
||||
const char *name;
|
||||
u8 idcode[IDCODE_LEN];
|
||||
u32 size;
|
||||
const struct sandbox_spi_flash_erase_commands
|
||||
erase_cmds[MAX_ERASE_CMDS];
|
||||
};
|
||||
|
||||
/* Structure describing all the flashes we know how to emulate */
|
||||
static const struct sandbox_spi_flash_data sandbox_sf_flashes[] = {
|
||||
{
|
||||
"M25P16", { 0x20, 0x20, 0x15 }, (2 << 20),
|
||||
{ /* erase commands */
|
||||
{ 0xd8, (64 << 10), }, /* sector */
|
||||
{ 0xc7, (2 << 20), }, /* bulk */
|
||||
},
|
||||
},
|
||||
{
|
||||
"W25Q32", { 0xef, 0x40, 0x16 }, (4 << 20),
|
||||
{ /* erase commands */
|
||||
{ 0x20, (4 << 10), }, /* 4KB */
|
||||
{ 0xd8, (64 << 10), }, /* sector */
|
||||
{ 0xc7, (4 << 20), }, /* bulk */
|
||||
},
|
||||
},
|
||||
{
|
||||
"W25Q128", { 0xef, 0x40, 0x18 }, (16 << 20),
|
||||
{ /* erase commands */
|
||||
{ 0x20, (4 << 10), }, /* 4KB */
|
||||
{ 0xd8, (64 << 10), }, /* sector */
|
||||
{ 0xc7, (16 << 20), }, /* bulk */
|
||||
},
|
||||
},
|
||||
};
|
||||
|
||||
/* Used to quickly bulk erase backing store */
|
||||
static u8 sandbox_sf_0xff[0x1000];
|
||||
|
||||
/* Internal state data for each SPI flash */
|
||||
struct sandbox_spi_flash {
|
||||
/*
|
||||
* As we receive data over the SPI bus, our flash transitions
|
||||
* between states. For example, we start off in the SF_CMD
|
||||
* state where the first byte tells us what operation to perform
|
||||
* (such as read or write the flash). But the operation itself
|
||||
* can go through a few states such as first reading in the
|
||||
* offset in the flash to perform the requested operation.
|
||||
* Thus "state" stores the exact state that our machine is in
|
||||
* while "cmd" stores the overall command we're processing.
|
||||
*/
|
||||
enum sandbox_sf_state state;
|
||||
uint cmd;
|
||||
const void *cmd_data;
|
||||
/* Current position in the flash; used when reading/writing/etc... */
|
||||
uint off;
|
||||
/* How many address bytes we've consumed */
|
||||
uint addr_bytes, pad_addr_bytes;
|
||||
/* The current flash status (see STAT_XXX defines above) */
|
||||
u16 status;
|
||||
/* Data describing the flash we're emulating */
|
||||
const struct sandbox_spi_flash_data *data;
|
||||
/* The file on disk to serv up data from */
|
||||
int fd;
|
||||
};
|
||||
|
||||
static int sandbox_sf_setup(void **priv, const char *spec)
|
||||
{
|
||||
/* spec = idcode:file */
|
||||
struct sandbox_spi_flash *sbsf;
|
||||
const char *file;
|
||||
size_t i, len, idname_len;
|
||||
const struct sandbox_spi_flash_data *data;
|
||||
|
||||
file = strchr(spec, ':');
|
||||
if (!file) {
|
||||
printf("sandbox_sf: unable to parse file\n");
|
||||
goto error;
|
||||
}
|
||||
idname_len = file - spec;
|
||||
++file;
|
||||
|
||||
for (i = 0; i < ARRAY_SIZE(sandbox_sf_flashes); ++i) {
|
||||
data = &sandbox_sf_flashes[i];
|
||||
len = strlen(data->name);
|
||||
if (idname_len != len)
|
||||
continue;
|
||||
if (!memcmp(spec, data->name, len))
|
||||
break;
|
||||
}
|
||||
if (i == ARRAY_SIZE(sandbox_sf_flashes)) {
|
||||
printf("sandbox_sf: unknown flash '%*s'\n", (int)idname_len,
|
||||
spec);
|
||||
goto error;
|
||||
}
|
||||
|
||||
if (sandbox_sf_0xff[0] == 0x00)
|
||||
memset(sandbox_sf_0xff, 0xff, sizeof(sandbox_sf_0xff));
|
||||
|
||||
sbsf = calloc(sizeof(*sbsf), 1);
|
||||
if (!sbsf) {
|
||||
printf("sandbox_sf: out of memory\n");
|
||||
goto error;
|
||||
}
|
||||
|
||||
sbsf->fd = os_open(file, 02);
|
||||
if (sbsf->fd == -1) {
|
||||
free(sbsf);
|
||||
printf("sandbox_sf: unable to open file '%s'\n", file);
|
||||
goto error;
|
||||
}
|
||||
|
||||
sbsf->data = data;
|
||||
|
||||
*priv = sbsf;
|
||||
return 0;
|
||||
|
||||
error:
|
||||
return 1;
|
||||
}
|
||||
|
||||
static void sandbox_sf_free(void *priv)
|
||||
{
|
||||
struct sandbox_spi_flash *sbsf = priv;
|
||||
|
||||
os_close(sbsf->fd);
|
||||
free(sbsf);
|
||||
}
|
||||
|
||||
static void sandbox_sf_cs_activate(void *priv)
|
||||
{
|
||||
struct sandbox_spi_flash *sbsf = priv;
|
||||
|
||||
debug("sandbox_sf: CS activated; state is fresh!\n");
|
||||
|
||||
/* CS is asserted, so reset state */
|
||||
sbsf->off = 0;
|
||||
sbsf->addr_bytes = 0;
|
||||
sbsf->pad_addr_bytes = 0;
|
||||
sbsf->state = SF_CMD;
|
||||
sbsf->cmd = SF_CMD;
|
||||
}
|
||||
|
||||
static void sandbox_sf_cs_deactivate(void *priv)
|
||||
{
|
||||
debug("sandbox_sf: CS deactivated; cmd done processing!\n");
|
||||
}
|
||||
|
||||
/* Figure out what command this stream is telling us to do */
|
||||
static int sandbox_sf_process_cmd(struct sandbox_spi_flash *sbsf, const u8 *rx,
|
||||
u8 *tx)
|
||||
{
|
||||
enum sandbox_sf_state oldstate = sbsf->state;
|
||||
|
||||
/* We need to output a byte for the cmd byte we just ate */
|
||||
sandbox_spi_tristate(tx, 1);
|
||||
|
||||
sbsf->cmd = rx[0];
|
||||
switch (sbsf->cmd) {
|
||||
case CMD_READ_ID:
|
||||
sbsf->state = SF_ID;
|
||||
sbsf->cmd = SF_ID;
|
||||
break;
|
||||
case CMD_READ_ARRAY_FAST:
|
||||
sbsf->pad_addr_bytes = 1;
|
||||
case CMD_READ_ARRAY_SLOW:
|
||||
case CMD_PAGE_PROGRAM:
|
||||
state_addr:
|
||||
sbsf->state = SF_ADDR;
|
||||
break;
|
||||
case CMD_WRITE_DISABLE:
|
||||
debug(" write disabled\n");
|
||||
sbsf->status &= ~STAT_WEL;
|
||||
break;
|
||||
case CMD_READ_STATUS:
|
||||
sbsf->state = SF_READ_STATUS;
|
||||
break;
|
||||
case CMD_READ_STATUS1:
|
||||
sbsf->state = SF_READ_STATUS1;
|
||||
break;
|
||||
case CMD_WRITE_ENABLE:
|
||||
debug(" write enabled\n");
|
||||
sbsf->status |= STAT_WEL;
|
||||
break;
|
||||
default: {
|
||||
size_t i;
|
||||
|
||||
/* handle erase commands first */
|
||||
for (i = 0; i < MAX_ERASE_CMDS; ++i) {
|
||||
const struct sandbox_spi_flash_erase_commands *
|
||||
erase_cmd = &sbsf->data->erase_cmds[i];
|
||||
|
||||
if (erase_cmd->cmd == 0x00)
|
||||
continue;
|
||||
if (sbsf->cmd != erase_cmd->cmd)
|
||||
continue;
|
||||
|
||||
sbsf->cmd_data = erase_cmd;
|
||||
goto state_addr;
|
||||
}
|
||||
|
||||
debug(" cmd unknown: %#x\n", sbsf->cmd);
|
||||
return 1;
|
||||
}
|
||||
}
|
||||
|
||||
if (oldstate != sbsf->state)
|
||||
debug(" cmd: transition to %s state\n",
|
||||
sandbox_sf_state_name(sbsf->state));
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int sandbox_erase_part(struct sandbox_spi_flash *sbsf, int size)
|
||||
{
|
||||
int todo;
|
||||
int ret;
|
||||
|
||||
while (size > 0) {
|
||||
todo = min(size, sizeof(sandbox_sf_0xff));
|
||||
ret = os_write(sbsf->fd, sandbox_sf_0xff, todo);
|
||||
if (ret != todo)
|
||||
return ret;
|
||||
size -= todo;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int sandbox_sf_xfer(void *priv, const u8 *rx, u8 *tx,
|
||||
uint bytes)
|
||||
{
|
||||
struct sandbox_spi_flash *sbsf = priv;
|
||||
uint cnt, pos = 0;
|
||||
int ret;
|
||||
|
||||
debug("sandbox_sf: state:%x(%s) bytes:%u\n", sbsf->state,
|
||||
sandbox_sf_state_name(sbsf->state), bytes);
|
||||
|
||||
if (sbsf->state == SF_CMD) {
|
||||
/* Figure out the initial state */
|
||||
if (sandbox_sf_process_cmd(sbsf, rx, tx))
|
||||
return 1;
|
||||
++pos;
|
||||
}
|
||||
|
||||
/* Process the remaining data */
|
||||
while (pos < bytes) {
|
||||
switch (sbsf->state) {
|
||||
case SF_ID: {
|
||||
u8 id;
|
||||
|
||||
debug(" id: off:%u tx:", sbsf->off);
|
||||
if (sbsf->off < IDCODE_LEN)
|
||||
id = sbsf->data->idcode[sbsf->off];
|
||||
else
|
||||
id = 0;
|
||||
debug("%02x\n", id);
|
||||
tx[pos++] = id;
|
||||
++sbsf->off;
|
||||
break;
|
||||
}
|
||||
case SF_ADDR:
|
||||
debug(" addr: bytes:%u rx:%02x ", sbsf->addr_bytes,
|
||||
rx[pos]);
|
||||
|
||||
if (sbsf->addr_bytes++ < SF_ADDR_LEN)
|
||||
sbsf->off = (sbsf->off << 8) | rx[pos];
|
||||
debug("addr:%06x\n", sbsf->off);
|
||||
|
||||
sandbox_spi_tristate(&tx[pos++], 1);
|
||||
|
||||
/* See if we're done processing */
|
||||
if (sbsf->addr_bytes <
|
||||
SF_ADDR_LEN + sbsf->pad_addr_bytes)
|
||||
break;
|
||||
|
||||
/* Next state! */
|
||||
if (os_lseek(sbsf->fd, sbsf->off, OS_SEEK_SET) < 0) {
|
||||
puts("sandbox_sf: os_lseek() failed");
|
||||
return 1;
|
||||
}
|
||||
switch (sbsf->cmd) {
|
||||
case CMD_READ_ARRAY_FAST:
|
||||
case CMD_READ_ARRAY_SLOW:
|
||||
sbsf->state = SF_READ;
|
||||
break;
|
||||
case CMD_PAGE_PROGRAM:
|
||||
sbsf->state = SF_WRITE;
|
||||
break;
|
||||
default:
|
||||
/* assume erase state ... */
|
||||
sbsf->state = SF_ERASE;
|
||||
goto case_sf_erase;
|
||||
}
|
||||
debug(" cmd: transition to %s state\n",
|
||||
sandbox_sf_state_name(sbsf->state));
|
||||
break;
|
||||
case SF_READ:
|
||||
/*
|
||||
* XXX: need to handle exotic behavior:
|
||||
* - reading past end of device
|
||||
*/
|
||||
|
||||
cnt = bytes - pos;
|
||||
debug(" tx: read(%u)\n", cnt);
|
||||
ret = os_read(sbsf->fd, tx + pos, cnt);
|
||||
if (ret < 0) {
|
||||
puts("sandbox_spi: os_read() failed\n");
|
||||
return 1;
|
||||
}
|
||||
pos += ret;
|
||||
break;
|
||||
case SF_READ_STATUS:
|
||||
debug(" read status: %#x\n", sbsf->status);
|
||||
cnt = bytes - pos;
|
||||
memset(tx + pos, sbsf->status, cnt);
|
||||
pos += cnt;
|
||||
break;
|
||||
case SF_READ_STATUS1:
|
||||
debug(" read status: %#x\n", sbsf->status);
|
||||
cnt = bytes - pos;
|
||||
memset(tx + pos, sbsf->status >> 8, cnt);
|
||||
pos += cnt;
|
||||
break;
|
||||
case SF_WRITE:
|
||||
/*
|
||||
* XXX: need to handle exotic behavior:
|
||||
* - unaligned addresses
|
||||
* - more than a page (256) worth of data
|
||||
* - reading past end of device
|
||||
*/
|
||||
if (!(sbsf->status & STAT_WEL)) {
|
||||
puts("sandbox_sf: write enable not set before write\n");
|
||||
goto done;
|
||||
}
|
||||
|
||||
cnt = bytes - pos;
|
||||
debug(" rx: write(%u)\n", cnt);
|
||||
sandbox_spi_tristate(&tx[pos], cnt);
|
||||
ret = os_write(sbsf->fd, rx + pos, cnt);
|
||||
if (ret < 0) {
|
||||
puts("sandbox_spi: os_write() failed\n");
|
||||
return 1;
|
||||
}
|
||||
pos += ret;
|
||||
sbsf->status &= ~STAT_WEL;
|
||||
break;
|
||||
case SF_ERASE:
|
||||
case_sf_erase: {
|
||||
const struct sandbox_spi_flash_erase_commands *
|
||||
erase_cmd = sbsf->cmd_data;
|
||||
|
||||
if (!(sbsf->status & STAT_WEL)) {
|
||||
puts("sandbox_sf: write enable not set before erase\n");
|
||||
goto done;
|
||||
}
|
||||
|
||||
/* verify address is aligned */
|
||||
if (sbsf->off & (erase_cmd->size - 1)) {
|
||||
debug(" sector erase: cmd:%#x needs align:%#x, but we got %#x\n",
|
||||
erase_cmd->cmd, erase_cmd->size,
|
||||
sbsf->off);
|
||||
sbsf->status &= ~STAT_WEL;
|
||||
goto done;
|
||||
}
|
||||
|
||||
debug(" sector erase addr: %u\n", sbsf->off);
|
||||
|
||||
cnt = bytes - pos;
|
||||
sandbox_spi_tristate(&tx[pos], cnt);
|
||||
pos += cnt;
|
||||
|
||||
/*
|
||||
* TODO(vapier@gentoo.org): latch WIP in status, and
|
||||
* delay before clearing it ?
|
||||
*/
|
||||
ret = sandbox_erase_part(sbsf, erase_cmd->size);
|
||||
sbsf->status &= ~STAT_WEL;
|
||||
if (ret) {
|
||||
debug("sandbox_sf: Erase failed\n");
|
||||
goto done;
|
||||
}
|
||||
goto done;
|
||||
}
|
||||
default:
|
||||
debug(" ??? no idea what to do ???\n");
|
||||
goto done;
|
||||
}
|
||||
}
|
||||
|
||||
done:
|
||||
return pos == bytes ? 0 : 1;
|
||||
}
|
||||
|
||||
static const struct sandbox_spi_emu_ops sandbox_sf_ops = {
|
||||
.setup = sandbox_sf_setup,
|
||||
.free = sandbox_sf_free,
|
||||
.cs_activate = sandbox_sf_cs_activate,
|
||||
.cs_deactivate = sandbox_sf_cs_deactivate,
|
||||
.xfer = sandbox_sf_xfer,
|
||||
};
|
||||
|
||||
static int sandbox_cmdline_cb_spi_sf(struct sandbox_state *state,
|
||||
const char *arg)
|
||||
{
|
||||
unsigned long bus, cs;
|
||||
const char *spec = sandbox_spi_parse_spec(arg, &bus, &cs);
|
||||
|
||||
if (!spec)
|
||||
return 1;
|
||||
|
||||
/*
|
||||
* It is safe to not make a copy of 'spec' because it comes from the
|
||||
* command line.
|
||||
*
|
||||
* TODO(sjg@chromium.org): It would be nice if we could parse the
|
||||
* spec here, but the problem is that no U-Boot init has been done
|
||||
* yet. Perhaps we can figure something out.
|
||||
*/
|
||||
state->spi[bus][cs].ops = &sandbox_sf_ops;
|
||||
state->spi[bus][cs].spec = spec;
|
||||
return 0;
|
||||
}
|
||||
SANDBOX_CMDLINE_OPT(spi_sf, 1, "connect a SPI flash: <bus>:<cs>:<id>:<file>");
|
||||
@ -28,6 +28,7 @@
|
||||
#define CMD_PAGE_PROGRAM 0x02
|
||||
#define CMD_WRITE_DISABLE 0x04
|
||||
#define CMD_READ_STATUS 0x05
|
||||
#define CMD_READ_STATUS1 0x35
|
||||
#define CMD_WRITE_ENABLE 0x06
|
||||
#define CMD_READ_CONFIG 0x35
|
||||
#define CMD_FLAG_STATUS 0x70
|
||||
|
||||
@ -13,6 +13,7 @@
|
||||
#include <malloc.h>
|
||||
#include <spi.h>
|
||||
#include <spi_flash.h>
|
||||
#include <asm/io.h>
|
||||
|
||||
#include "sf_internal.h"
|
||||
|
||||
@ -279,7 +280,7 @@ int spi_flash_decode_fdt(const void *blob, struct spi_flash *flash)
|
||||
debug("%s: Memory map must cover entire device\n", __func__);
|
||||
return -1;
|
||||
}
|
||||
flash->memory_map = (void *)addr;
|
||||
flash->memory_map = map_sysmem(addr, size);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
Loading…
Reference in New Issue
Block a user