Merge git://www.denx.de/git/u-boot-marvell

drivers/net/phy/marvell.c

@@ -480,6 +480,49 @@ static int m88e1310_config(struct phy_device *phydev)
 	return genphy_config_aneg(phydev);
 }
 
+static int m88e1680_config(struct phy_device *phydev)
+{
+	/*
+	 * As per Marvell Release Notes - Alaska V 88E1680 Rev A2
+	 * Errata Section 4.1
+	 */
+	u16 reg;
+	int res;
+
+	/* Matrix LED mode (not neede if single LED mode is used */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0004);
+	reg = phy_read(phydev, MDIO_DEVAD_NONE, 27);
+	reg |= (1 << 5);
+	phy_write(phydev, MDIO_DEVAD_NONE, 27, reg);
+
+	/* QSGMII TX amplitude change */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x00fd);
+	phy_write(phydev, MDIO_DEVAD_NONE,  8, 0x0b53);
+	phy_write(phydev, MDIO_DEVAD_NONE,  7, 0x200d);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000);
+
+	/* EEE initialization */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x00ff);
+	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xb030);
+	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x215c);
+	phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x00fc);
+	phy_write(phydev, MDIO_DEVAD_NONE, 24, 0x888c);
+	phy_write(phydev, MDIO_DEVAD_NONE, 25, 0x888c);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000);
+	phy_write(phydev, MDIO_DEVAD_NONE,  0, 0x9140);
+
+	res = genphy_config_aneg(phydev);
+	if (res < 0)
+		return res;
+
+	/* soft reset */
+	reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+	reg |= BMCR_RESET;
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, reg);
+
+	return 0;
+}
+
 static struct phy_driver M88E1011S_driver = {
 	.name = "Marvell 88E1011S",
 	.uid = 0x1410c60,
@@ -580,6 +623,16 @@ static struct phy_driver M88E1310_driver = {
 	.shutdown = &genphy_shutdown,
 };
 
+static struct phy_driver M88E1680_driver = {
+	.name = "Marvell 88E1680",
+	.uid = 0x1410ed0,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1680_config,
+	.startup = &genphy_startup,
+	.shutdown = &genphy_shutdown,
+};
+
 int phy_marvell_init(void)
 {
 	phy_register(&M88E1310_driver);
@@ -592,6 +645,7 @@ int phy_marvell_init(void)
 	phy_register(&M88E1011S_driver);
 	phy_register(&M88E1510_driver);
 	phy_register(&M88E1518_driver);
+	phy_register(&M88E1680_driver);
 
 	return 0;
 }

drivers/pci/pci_mvebu.c

@@ -91,25 +91,26 @@ static void __iomem *mvebu_pcie_membase = (void __iomem *)MBUS_PCI_MEM_BASE;
 #if defined(CONFIG_ARMADA_38X)
 #define PCIE_BASE(if)					\
 	((if) == 0 ?					\
-	 MVEBU_REG_PCIE_BASE + 0x40000 :		\
-	 MVEBU_REG_PCIE_BASE + 0x4000 * (if))
+	 MVEBU_REG_PCIE0_BASE :				\
+	 (MVEBU_REG_PCIE_BASE + 0x4000 * (if - 1)))
 
 /*
  * On A38x MV6820 these PEX ports are supported:
  *  0 - Port 0.0
- *  1 - Port 0.1
- *  2 - Port 0.2
+ *  1 - Port 1.0
+ *  2 - Port 2.0
+ *  3 - Port 3.0
  */
-#define MAX_PEX 3
+#define MAX_PEX 4
 static struct mvebu_pcie pcie_bus[MAX_PEX];
 
 static void mvebu_get_port_lane(struct mvebu_pcie *pcie, int pex_idx,
 				int *mem_target, int *mem_attr)
 {
-	u8 port[] = { 0, 1, 2 };
-	u8 lane[] = { 0, 0, 0 };
-	u8 target[] = { 8, 4, 4 };
-	u8 attr[] = { 0xe8, 0xe8, 0xd8 };
+	u8 port[] = { 0, 1, 2, 3 };
+	u8 lane[] = { 0, 0, 0, 0 };
+	u8 target[] = { 8, 4, 4, 4 };
+	u8 attr[] = { 0xe8, 0xe8, 0xd8, 0xb8 };
 
 	pcie->port = port[pex_idx];
 	pcie->lane = lane[pex_idx];
@@ -351,9 +352,9 @@ void pci_init_board(void)
 		mvebu_get_port_lane(pcie, i, &mem_target, &mem_attr);
 
 		/* Don't read at all from pci registers if port power is down */
-		if (pcie->lane == 0 && SELECT(soc_ctrl, pcie->port) == 0) {
-			i += 3;
-			debug("%s: skipping port %d\n", __func__, pcie->port);
+		if (SELECT(soc_ctrl, pcie->port) == 0) {
+			if (pcie->lane == 0)
+				debug("%s: skipping port %d\n", __func__, pcie->port);
 			continue;
 		}
 

drivers/phy/marvell/comphy_a3700.c

@@ -884,11 +884,10 @@ void comphy_dedicated_phys_init(void)
 	}
 
 	node = fdt_node_offset_by_compatible(blob, -1,
-					     "marvell,armada-3700-sdio");
+					     "marvell,armada-8k-sdhci");
 	if (node <= 0) {
-		debug("No SDIO node in DT, looking for MMC one\n");
-		node = fdt_node_offset_by_compatible(blob, -1,
-						     "marvell,xenon-sdhci");
+		node = fdt_node_offset_by_compatible(
+			blob, -1, "marvell,armada-3700-sdhci");
 	}
 
 	if (node > 0) {

drivers/tpm/Kconfig

@@ -82,4 +82,10 @@ config TPM_ST33ZP24_SPI
 	  to the device using the standard TPM Interface Specification (TIS)
 	  protocol
 
+config TPM_FLUSH_RESOURCES
+	bool "Enable TPM resource flushing support"
+	depends on TPM
+	help
+	  Enable support to flush specific resources (e.g. keys) from the TPM.
+	  The functionality is available via the 'tpm' command as well.
 endmenu