diff --git a/doc/README.rockchip b/doc/README.rockchip
index 364affd56f..e0572c80b9 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -14,7 +14,7 @@ many Rockchip devices [1] [2].
The current mainline support is experimental only and is not useful for
anything. It should provide a base on which to build.
-So far only support for the RK3288 is provided.
+So far only support for the RK3288 and RK3036 is provided.
Prerequisites
@@ -22,7 +22,7 @@ Prerequisites
You will need:
- - Firefly RK3288 baord
+ - Firefly RK3288 board or something else with a supported RockChip SoC
- Power connection to 5V using the supplied micro-USB power cable
- Separate USB serial cable attached to your computer and the Firefly
(connect to the micro-USB connector below the logo)
@@ -40,11 +40,12 @@ At present three RK3288 boards are supported:
- Firefly RK3288 - use firefly-rk3288 configuration
- Radxa Rock 2 - use rock2 configuration
- - Haier Chromebook - use chromebook_jerry configuration
+ - Hisense Chromebook - use chromebook_jerry configuration
-one RK3036 board is support:
+Two RK3036 board are supported:
- - EVB RK3036 - use evb-rk3036_defconfig configuration
+ - EVB RK3036 - use evb-rk3036 configuration
+ - Kylin - use kylin_rk3036 configuration
For example:
@@ -103,20 +104,23 @@ corresponds with this setting in U-Boot:
Put this SD (or micro-SD) card into your board and reset it. You should see
something like:
- U-Boot SPL 2015.07-rc1-00383-ge345740-dirty (Jun 03 2015 - 11:04:40)
-
-
- U-Boot 2015.07-rc1-00383-ge345740-dirty (Jun 03 2015 - 11:04:40)
+ U-Boot 2016.01-rc2-00309-ge5bad3b-dirty (Jan 02 2016 - 23:41:59 -0700)
+ Model: Radxa Rock 2 Square
DRAM: 2 GiB
- MMC:
- Using default environment
+ MMC: dwmmc@ff0f0000: 0, dwmmc@ff0c0000: 1
+ *** Warning - bad CRC, using default environment
- In: serial@ff690000
- Out: serial@ff690000
- Err: serial@ff690000
+ In: serial
+ Out: vop@ff940000.vidconsole
+ Err: serial
+ Net: Net Initialization Skipped
+ No ethernet found.
+ Hit any key to stop autoboot: 0
=>
+If you have an HDMI cable attached you should see a video console.
+
For evb_rk3036 board:
./evb-rk3036/tools/mkimage -n rk3036 -T rksd -d evb-rk3036/spl/u-boot-spl.bin out && \
cat evb-rk3036/u-boot-dtb.bin >> out && \
@@ -170,13 +174,9 @@ Future work
Immediate priorities are:
-- GPIO (driver exists but is lightly tested)
-- I2C (driver exists but is non-functional)
- USB host
- USB device
-- PMIC and regulators (only ACT8846 is supported at present)
-- LCD and HDMI
-- Run CPU at full speed
+- Run CPU at full speed (code exists but we only see ~60 DMIPS maximum)
- Ethernet
- NAND flash
- Support for other Rockchip parts