powerpc/t1042RDB: Add Video - HDMI support

T1042 has internal display interface unit (DIU) for driving video.
T1042RDB supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder

Chrontel, CH7301C encoder which is I2C programmable is used
as HDMI connector on T1042RDB.
This patch add support to
-enable Video interface for T1042RDB
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1042
-program HDMI encoder via I2C on board

This patch refer to the upstream diu patch
(337b0c52b3) for T1040qds.

Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[York Sun: resolve conflict and move changes to T104xRDB.h]
Reviewed-by: York Sun <yorksun@freescale.com>

board/freescale/t104xrdb/Makefile

@@ -11,6 +11,7 @@ obj-y	+= t104xrdb.o
 obj-y	+= cpld.o
 obj-y	+= eth.o
 obj-$(CONFIG_PCI)	+= pci.o
+obj-$(CONFIG_FSL_DIU_FB)+= diu.o
 endif
 obj-y	+= ddr.o
 obj-y	+= law.o

board/freescale/t104xrdb/diu.c

@@ -0,0 +1,84 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Author: Priyanka Jain <Priyanka.Jain@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/io.h>
+#include <common.h>
+#include <command.h>
+#include <fsl_diu_fb.h>
+#include <linux/ctype.h>
+#include <video_fb.h>
+
+#include "../common/diu_ch7301.h"
+
+#include "cpld.h"
+#include "t104xrdb.h"
+
+/*
+ * DIU Area Descriptor
+ *
+ * Note that we need to byte-swap the value before it's written to the AD
+ * register. So even though the registers don't look like they're in the same
+ * bit positions as they are on the MPC8610, the same value is written to the
+ * AD register on the MPC8610 and on the P1022.
+ */
+#define AD_BYTE_F		0x10000000
+#define AD_ALPHA_C_SHIFT	25
+#define AD_BLUE_C_SHIFT		23
+#define AD_GREEN_C_SHIFT	21
+#define AD_RED_C_SHIFT		19
+#define AD_PIXEL_S_SHIFT	16
+#define AD_COMP_3_SHIFT		12
+#define AD_COMP_2_SHIFT		8
+#define AD_COMP_1_SHIFT		4
+#define AD_COMP_0_SHIFT		0
+
+void diu_set_pixel_clock(unsigned int pixclock)
+{
+	unsigned long speed_ccb, temp;
+	u32 pixval;
+	int ret;
+
+	speed_ccb = get_bus_freq(0);
+	temp = 1000000000 / pixclock;
+	temp *= 1000;
+	pixval = speed_ccb / temp;
+
+	/* Program HDMI encoder */
+	ret = diu_set_dvi_encoder(temp);
+	if (ret) {
+		puts("Failed to set DVI encoder\n");
+		return;
+	}
+
+	/* Program pixel clock */
+	out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR,
+		 ((pixval << PXCK_BITS_START) & PXCK_MASK));
+
+	/* enable clock*/
+	out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR, PXCKEN_MASK |
+		 ((pixval << PXCK_BITS_START) & PXCK_MASK));
+}
+
+int platform_diu_init(unsigned int xres, unsigned int yres, const char *port)
+{
+	u32 pixel_format;
+	u8 sw;
+
+	/*Configure Display ouput port as HDMI*/
+	sw = CPLD_READ(sfp_ctl_status);
+	CPLD_WRITE(sfp_ctl_status , sw & ~(CPLD_DIU_SEL_DFP));
+
+	pixel_format = cpu_to_le32(AD_BYTE_F | (3 << AD_ALPHA_C_SHIFT) |
+		(0 << AD_BLUE_C_SHIFT) | (1 << AD_GREEN_C_SHIFT) |
+		(2 << AD_RED_C_SHIFT) | (8 << AD_COMP_3_SHIFT) |
+		(8 << AD_COMP_2_SHIFT) | (8 << AD_COMP_1_SHIFT) |
+		(8 << AD_COMP_0_SHIFT) | (3 << AD_PIXEL_S_SHIFT));
+
+	printf("DIU: Switching to monitor DVI @ %ux%u\n",  xres, yres);
+
+	return fsl_diu_init(xres, yres, pixel_format, 0);
+}

include/configs/T104xRDB.h

@@ -268,6 +268,9 @@
 #define CPLD_LBMAP_DFLTBANK		0x40 /* BANK OR | BANK0 */
 #define CPLD_LBMAP_RESET		0xFF
 #define CPLD_LBMAP_SHIFT		0x03
+#ifdef CONFIG_T1042RDB_PI
+#define CPLD_DIU_SEL_DFP		0x80
+#endif
 
 #define CONFIG_SYS_CPLD_BASE	0xffdf0000
 #define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
@@ -429,6 +432,24 @@
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 
+#ifdef CONFIG_T1042RDB_PI
+/* Video */
+#define CONFIG_FSL_DIU_FB
+
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_FSL_DIU_CH7301
+#define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x180000)
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_CFB_CONSOLE_ANSI
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#endif
+#endif
+
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
@@ -461,6 +482,10 @@
 #endif
 
 #ifdef CONFIG_T1042RDB_PI
+/* LDI/DVI Encoder for display */
+#define CONFIG_SYS_I2C_LDI_ADDR		0x38
+#define CONFIG_SYS_I2C_DVI_ADDR		0x75
+
 /*
  * RTC configuration
  */
@@ -772,11 +797,18 @@
 #define RAMDISKFILE	"t1040rdb_pi/ramdisk.uboot"
 #endif
 
+#ifdef CONFIG_FSL_DIU_FB
+#define DIU_ENVIRONMENT "video-mode=fslfb:1024x768-32@60,monitor=dvi"
+#else
+#define DIU_ENVIRONMENT
+#endif
+
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"hwconfig=fsl_ddr:bank_intlv=cs0_cs1;"			\
 	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
 	"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 	"netdev=eth0\0"						\
+	"video-mode=" __stringify(DIU_ENVIRONMENT) "\0"		\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
 	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
 	"tftpflash=tftpboot $loadaddr $uboot && "		\