spl: Move all VPL, TPL and PowerPC specific CONFIG options to separate files
- Move all PowerPC (and some shared with Layerscape) options to common/spl/Kconfig.nxp - Move all other TPL related options to common/spl/Kconfig.tpl - Move all VPL related options to common/spl/Kconfig.vpl This makes the whole of common/spl/Kconfig slightly more readable. Signed-off-by: Tom Rini <trini@konsulko.com>
This commit is contained in:
Tom Rini
parent
3ff2aa6d04
commit
ba787bb458
@ -199,117 +199,7 @@ config SPL_BINMAN_SYMBOLS
|
||||
For this to work, you must have a U-Boot image in the binman image, so
|
||||
binman can update SPL with the location of it.
|
||||
|
||||
menu "PowerPC and LayerScape SPL Boot options"
|
||||
|
||||
config SPL_NAND_BOOT
|
||||
bool "Load SPL from NAND flash"
|
||||
depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_MMC_BOOT
|
||||
bool "Load SPL from SD Card / eMMC"
|
||||
depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_SPI_BOOT
|
||||
bool "Load SPL from SPI flash"
|
||||
depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_FSL_PBL
|
||||
bool "Create SPL in Freescale PBI format"
|
||||
depends on (PPC || ARCH_LS1021A || ARCH_LS1043A || ARCH_LS1046A) && \
|
||||
SUPPORT_SPL
|
||||
help
|
||||
Create boot binary having SPL binary in PBI format concatenated with
|
||||
u-boot binary.
|
||||
|
||||
config SPL_SYS_CCSR_DO_NOT_RELOCATE
|
||||
bool "Ensures that CCSR is not relocated"
|
||||
depends on PPC
|
||||
help
|
||||
If this is defined, then CONFIG_SYS_CCSRBAR_PHYS will be forced to a
|
||||
value that ensures that CCSR is not relocated.
|
||||
|
||||
config TPL_SYS_CCSR_DO_NOT_RELOCATE
|
||||
def_bool y
|
||||
depends on SPL_SYS_CCSR_DO_NOT_RELOCATE
|
||||
|
||||
endmenu
|
||||
|
||||
menu "PowerPC SPL / TPL specific options"
|
||||
depends on PPC && (SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_INIT_MINIMAL
|
||||
bool "Arch init code will be built for a very small image"
|
||||
|
||||
config SPL_FLUSH_IMAGE
|
||||
bool "Clean dcache and invalidate icache after loading the image"
|
||||
|
||||
config SPL_SKIP_RELOCATE
|
||||
bool "Skip relocating SPL"
|
||||
|
||||
config SPL_GD_ADDR
|
||||
hex "Address to use for global data (gd) in SPL"
|
||||
depends on !SPL_INIT_MINIMAL
|
||||
|
||||
config SPL_RELOC_TEXT_BASE
|
||||
hex "Address to relocate SPL to"
|
||||
default SPL_TEXT_BASE
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_SPL_TEXT_BASE (i.e. no
|
||||
relocation is done).
|
||||
|
||||
config SPL_RELOC_STACK
|
||||
hex "Address of the start of the stack SPL will use after relocation."
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_SYS_SPL_MALLOC_START. Starting
|
||||
address of the malloc pool used in SPL. When this option is set the full
|
||||
malloc is used in SPL and it is set up by spl_init() and before that, the
|
||||
simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.
|
||||
|
||||
config SPL_RELOC_MALLOC
|
||||
bool "SPL has malloc pool after relocation"
|
||||
|
||||
config SPL_RELOC_MALLOC_ADDR
|
||||
hex "Address of malloc pool in SPL"
|
||||
depends on SPL_RELOC_MALLOC
|
||||
|
||||
config SPL_RELOC_MALLOC_SIZE
|
||||
hex "Size of malloc pool in SPL"
|
||||
depends on SPL_RELOC_MALLOC
|
||||
|
||||
config TPL_GD_ADDR
|
||||
hex "Address to use for global data (gd) in TPL"
|
||||
depends on TPL
|
||||
|
||||
config TPL_RELOC_TEXT_BASE
|
||||
hex "Address to relocate TPL to"
|
||||
depends on TPL
|
||||
default TPL_TEXT_BASE
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_TPL_TEXT_BASE (i.e. no
|
||||
relocation is done).
|
||||
|
||||
config TPL_RELOC_STACK
|
||||
hex "Address of the start of the stack TPL will use after relocation."
|
||||
depends on TPL
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_SYS_TPL_MALLOC_START. Starting
|
||||
address of the malloc pool used in TPL. When this option is set the full
|
||||
malloc is used in TPL and it is set up by spl_init() and before that, the
|
||||
simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.
|
||||
|
||||
config TPL_RELOC_MALLOC
|
||||
bool "TPL has malloc pool after relocation"
|
||||
depends on TPL
|
||||
|
||||
config TPL_RELOC_MALLOC_ADDR
|
||||
hex "Address of malloc pool in TPL"
|
||||
depends on TPL_RELOC_MALLOC
|
||||
|
||||
config TPL_RELOC_MALLOC_SIZE
|
||||
hex "Size of malloc pool in TPL"
|
||||
depends on TPL_RELOC_MALLOC
|
||||
|
||||
endmenu
|
||||
source "common/spl/Kconfig.nxp"
|
||||
|
||||
config HANDOFF
|
||||
bool "Pass hand-off information from SPL to U-Boot proper"
|
||||
@ -360,13 +250,6 @@ config SPL_BOARD_INIT
|
||||
spl_board_init() from board_init_r(). This function should be
|
||||
provided by the board.
|
||||
|
||||
config VPL_BOARD_INIT
|
||||
bool "Call board-specific initialization in VPL"
|
||||
help
|
||||
If this option is enabled, U-Boot will call the function
|
||||
spl_board_init() from board_init_r(). This function should be
|
||||
provided by the board.
|
||||
|
||||
config SPL_BOOTROM_SUPPORT
|
||||
bool "Support returning to the BOOTROM"
|
||||
help
|
||||
@ -425,16 +308,6 @@ config SPL_SYS_MALLOC_SIMPLE
|
||||
this will make the SPL binary smaller at the cost of more heap
|
||||
usage as the *_simple malloc functions do not re-use free-ed mem.
|
||||
|
||||
config TPL_SYS_MALLOC_SIMPLE
|
||||
bool
|
||||
prompt "Only use malloc_simple functions in the TPL"
|
||||
depends on TPL
|
||||
help
|
||||
Say Y here to only use the *_simple malloc functions from
|
||||
malloc_simple.c, rather then using the versions from dlmalloc.c;
|
||||
this will make the TPL binary smaller at the cost of more heap
|
||||
usage as the *_simple malloc functions do not re-use free-ed mem.
|
||||
|
||||
config SPL_SHARES_INIT_SP_ADDR
|
||||
bool "SPL and U-Boot use the same initial stack pointer location"
|
||||
depends on (ARM || ARCH_JZ47XX || MICROBLAZE || RISCV) && SPL_FRAMEWORK
|
||||
@ -523,16 +396,6 @@ config SPL_READ_ONLY
|
||||
writeable memory) of anything it wants to modify, such as
|
||||
device-private data.
|
||||
|
||||
config TPL_SEPARATE_BSS
|
||||
bool "BSS section is in a different memory region from text"
|
||||
default y if SPL_SEPARATE_BSS
|
||||
help
|
||||
Some platforms need a large BSS region in TPL and can provide this
|
||||
because RAM is already set up. In this case BSS can be moved to RAM.
|
||||
This option should then be enabled so that the correct device tree
|
||||
location is used. Normally we put the device tree at the end of BSS
|
||||
but with this option enabled, it goes at _image_binary_end.
|
||||
|
||||
config SPL_BANNER_PRINT
|
||||
bool "Enable output of the SPL banner 'U-Boot SPL ...'"
|
||||
default y
|
||||
@ -541,15 +404,6 @@ config SPL_BANNER_PRINT
|
||||
info. Disabling this option could be useful to reduce SPL boot time
|
||||
(e.g. approx. 6 ms faster, when output on i.MX6 with 115200 baud).
|
||||
|
||||
config TPL_BANNER_PRINT
|
||||
bool "Enable output of the TPL banner 'U-Boot TPL ...'"
|
||||
depends on TPL
|
||||
default y
|
||||
help
|
||||
If this option is enabled, TPL will print the banner with version
|
||||
info. Disabling this option could be useful to reduce TPL boot time
|
||||
(e.g. approx. 6 ms faster, when output on i.MX6 with 115200 baud).
|
||||
|
||||
config SPL_EARLY_BSS
|
||||
depends on ARM && !ARM64
|
||||
bool "Allows initializing BSS early before entering board_init_f"
|
||||
@ -1625,314 +1479,7 @@ config TPL
|
||||
help
|
||||
If you want to build TPL as well as the normal image and SPL, say Y.
|
||||
|
||||
if TPL
|
||||
|
||||
config TPL_SIZE_LIMIT
|
||||
hex "Maximum size of TPL image"
|
||||
depends on TPL
|
||||
default 0x0
|
||||
help
|
||||
Specifies the maximum length of the U-Boot TPL image.
|
||||
If this value is zero, it is ignored.
|
||||
|
||||
config TPL_BINMAN_SYMBOLS
|
||||
bool "Declare binman symbols in TPL"
|
||||
depends on SPL_FRAMEWORK && BINMAN
|
||||
default y
|
||||
help
|
||||
This enables use of symbols in TPL which refer to U-Boot, enabling TPL
|
||||
to obtain the location of U-Boot simply by calling spl_get_image_pos()
|
||||
and spl_get_image_size().
|
||||
|
||||
For this to work, you must have a U-Boot image in the binman image, so
|
||||
binman can update TPL with the location of it.
|
||||
|
||||
config TPL_FRAMEWORK
|
||||
bool "Support TPL based upon the common SPL framework"
|
||||
default y if SPL_FRAMEWORK
|
||||
help
|
||||
Enable the SPL framework under common/spl/ for TPL builds.
|
||||
This framework supports MMC, NAND and YMODEM and other methods
|
||||
loading of U-Boot's SPL stage. If unsure, say Y.
|
||||
|
||||
config TPL_HANDOFF
|
||||
bool "Pass hand-off information from TPL to SPL and U-Boot proper"
|
||||
depends on HANDOFF && TPL_BLOBLIST
|
||||
default y
|
||||
help
|
||||
This option enables TPL to write handoff information. This can be
|
||||
used to pass information like the size of SDRAM from TPL to U-Boot
|
||||
proper. The information is also available to SPL if it is useful
|
||||
there.
|
||||
|
||||
config TPL_BOARD_INIT
|
||||
bool "Call board-specific initialization in TPL"
|
||||
help
|
||||
If this option is enabled, U-Boot will call the function
|
||||
spl_board_init() from board_init_r(). This function should be
|
||||
provided by the board.
|
||||
|
||||
config TPL_BOOTCOUNT_LIMIT
|
||||
bool "Support bootcount in TPL"
|
||||
depends on TPL_ENV_SUPPORT
|
||||
help
|
||||
If this option is enabled, the TPL will support bootcount.
|
||||
For example, it may be useful to choose the device to boot.
|
||||
|
||||
config TPL_LDSCRIPT
|
||||
string "Linker script for the TPL stage"
|
||||
depends on TPL
|
||||
default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
|
||||
default "arch/\$(ARCH)/cpu/u-boot-spl.lds"
|
||||
help
|
||||
The TPL stage will usually require a different linker-script
|
||||
(as it runs from a different memory region) than the regular
|
||||
U-Boot stage. Set this to the path of the linker-script to
|
||||
be used for TPL.
|
||||
|
||||
May be left empty to trigger the Makefile infrastructure to
|
||||
fall back to the linker-script used for the SPL stage.
|
||||
|
||||
config TPL_NEEDS_SEPARATE_STACK
|
||||
bool "TPL needs a separate initial stack-pointer"
|
||||
depends on TPL
|
||||
help
|
||||
Enable, if the TPL stage should not inherit its initial
|
||||
stack-pointer from the settings for the SPL stage.
|
||||
|
||||
config TPL_POWER
|
||||
bool "Support power drivers"
|
||||
help
|
||||
Enable support for power control in TPL. This includes support
|
||||
for PMICs (Power-management Integrated Circuits) and some of the
|
||||
features provided by PMICs. In particular, voltage regulators can
|
||||
be used to enable/disable power and vary its voltage. That can be
|
||||
useful in TPL to turn on boot peripherals and adjust CPU voltage
|
||||
so that the clock speed can be increased. This enables the drivers
|
||||
in drivers/power, drivers/power/pmic and drivers/power/regulator
|
||||
as part of an TPL build.
|
||||
|
||||
config TPL_TEXT_BASE
|
||||
hex "Base address for the .text section of the TPL stage"
|
||||
default 0
|
||||
help
|
||||
The base address for the .text section of the TPL stage.
|
||||
|
||||
config TPL_MAX_SIZE
|
||||
hex "Maximum size (in bytes) for the TPL stage"
|
||||
default 0x2e000 if ROCKCHIP_RK3399
|
||||
default 0x8000 if ROCKCHIP_RK3288
|
||||
default 0x7000 if ROCKCHIP_RK322X || ROCKCHIP_RK3328 || ROCKCHIP_RK3368
|
||||
default 0x2800 if ROCKCHIP_PX30
|
||||
default 0x0
|
||||
help
|
||||
The maximum size (in bytes) of the TPL stage.
|
||||
|
||||
config TPL_PAD_TO
|
||||
hex "Offset to which the TPL should be padded before appending the TPL payload"
|
||||
depends on !TPL_FRAMEWORK && PPC
|
||||
default TPL_MAX_SIZE
|
||||
help
|
||||
Image offset to which the TPL should be padded before appending the
|
||||
TPL payload. By default, this is defined as CONFIG_TPL_MAX_SIZE, or 0 if
|
||||
CONFIG_TPL_MAX_SIZE is undefined. CONFIG_TPL_PAD_TO must be either
|
||||
0, meaning to append the TPL payload without any padding, or >=
|
||||
CONFIG_TPL_MAX_SIZE.
|
||||
|
||||
config TPL_STACK
|
||||
hex "Address of the initial stack-pointer for the TPL stage"
|
||||
depends on TPL_NEEDS_SEPARATE_STACK
|
||||
help
|
||||
The address of the initial stack-pointer for the TPL stage.
|
||||
Usually this will be the (aligned) top-of-stack.
|
||||
|
||||
config TPL_READ_ONLY
|
||||
bool
|
||||
depends on TPL_OF_PLATDATA
|
||||
select TPL_OF_PLATDATA_NO_BIND
|
||||
select TPL_OF_PLATDATA_RT
|
||||
help
|
||||
Some platforms (e.g. x86 Apollo Lake) load SPL into a read-only
|
||||
section of memory. This means that of-platdata must make a copy (in
|
||||
writeable memory) of anything it wants to modify, such as
|
||||
device-private data.
|
||||
|
||||
config TPL_BOOTROM_SUPPORT
|
||||
bool "Support returning to the BOOTROM (from TPL)"
|
||||
help
|
||||
Some platforms (e.g. the Rockchip RK3368) provide support in their
|
||||
ROM for loading the next boot-stage after performing basic setup
|
||||
from the TPL stage.
|
||||
|
||||
Enable this option, to return to the BOOTROM through the
|
||||
BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
|
||||
boot device list, if not implemented for a given board)
|
||||
|
||||
config TPL_CRC32
|
||||
bool "Support CRC32 in TPL"
|
||||
default y if TPL_ENV_SUPPORT || TPL_BLOBLIST
|
||||
help
|
||||
Enable this to support CRC32 in uImages or FIT images within SPL.
|
||||
This is a 32-bit checksum value that can be used to verify images.
|
||||
For FIT images, this is the least secure type of checksum, suitable
|
||||
for detected accidental image corruption. For secure applications you
|
||||
should consider SHA1 or SHA256.
|
||||
|
||||
config TPL_DRIVERS_MISC
|
||||
bool "Support misc drivers in TPL"
|
||||
help
|
||||
Enable miscellaneous drivers in TPL. These drivers perform various
|
||||
tasks that don't fall nicely into other categories, Enable this
|
||||
option to build the drivers in drivers/misc as part of an TPL
|
||||
build, for those that support building in TPL (not all drivers do).
|
||||
|
||||
config TPL_ENV_SUPPORT
|
||||
bool "Support an environment"
|
||||
help
|
||||
Enable environment support in TPL. See SPL_ENV_SUPPORT for details.
|
||||
|
||||
config TPL_GPIO
|
||||
bool "Support GPIO in TPL"
|
||||
help
|
||||
Enable support for GPIOs (General-purpose Input/Output) in TPL.
|
||||
GPIOs allow U-Boot to read the state of an input line (high or
|
||||
low) and set the state of an output line. This can be used to
|
||||
drive LEDs, control power to various system parts and read user
|
||||
input. GPIOs can be useful in TPL to enable a 'sign-of-life' LED,
|
||||
for example. Enable this option to build the drivers in
|
||||
drivers/gpio as part of an TPL build.
|
||||
|
||||
config TPL_I2C
|
||||
bool "Support I2C"
|
||||
help
|
||||
Enable support for the I2C bus in TPL. See SPL_I2C for
|
||||
details.
|
||||
|
||||
config TPL_LIBCOMMON_SUPPORT
|
||||
bool "Support common libraries"
|
||||
help
|
||||
Enable support for common U-Boot libraries within TPL. See
|
||||
SPL_LIBCOMMON_SUPPORT for details.
|
||||
|
||||
config TPL_LIBGENERIC_SUPPORT
|
||||
bool "Support generic libraries"
|
||||
help
|
||||
Enable support for generic U-Boot libraries within TPL. See
|
||||
SPL_LIBGENERIC_SUPPORT for details.
|
||||
|
||||
config TPL_MPC8XXX_INIT_DDR
|
||||
bool "Support MPC8XXX DDR init"
|
||||
help
|
||||
Enable support for DDR-SDRAM on the MPC8XXX family within TPL. See
|
||||
SPL_MPC8XXX_INIT_DDR for details.
|
||||
|
||||
config TPL_MMC
|
||||
bool "Support MMC"
|
||||
depends on MMC
|
||||
help
|
||||
Enable support for MMC within TPL. See SPL_MMC for details.
|
||||
|
||||
config TPL_NAND_SUPPORT
|
||||
bool "Support NAND flash"
|
||||
help
|
||||
Enable support for NAND in TPL. See SPL_NAND_SUPPORT for details.
|
||||
|
||||
config TPL_PCI
|
||||
bool "Support PCI drivers"
|
||||
help
|
||||
Enable support for PCI in TPL. For platforms that need PCI to boot,
|
||||
or must perform some init using PCI in SPL, this provides the
|
||||
necessary driver support. This enables the drivers in drivers/pci
|
||||
as part of a TPL build.
|
||||
|
||||
config TPL_PCH
|
||||
bool "Support PCH drivers"
|
||||
help
|
||||
Enable support for PCH (Platform Controller Hub) devices in TPL.
|
||||
These are used to set up GPIOs and the SPI peripheral early in
|
||||
boot. This enables the drivers in drivers/pch as part of a TPL
|
||||
build.
|
||||
|
||||
config TPL_RAM_SUPPORT
|
||||
bool "Support booting from RAM"
|
||||
help
|
||||
Enable booting of an image in RAM. The image can be preloaded or
|
||||
it can be loaded by TPL directly into RAM (e.g. using USB).
|
||||
|
||||
config TPL_RAM_DEVICE
|
||||
bool "Support booting from preloaded image in RAM"
|
||||
depends on TPL_RAM_SUPPORT
|
||||
help
|
||||
Enable booting of an image already loaded in RAM. The image has to
|
||||
be already in memory when TPL takes over, e.g. loaded by the boot
|
||||
ROM.
|
||||
|
||||
config TPL_RTC
|
||||
bool "Support RTC drivers"
|
||||
help
|
||||
Enable RTC (Real-time Clock) support in TPL. This includes support
|
||||
for reading and setting the time. Some RTC devices also have some
|
||||
non-volatile (battery-backed) memory which is accessible if
|
||||
needed. This enables the drivers in drivers/rtc as part of an TPL
|
||||
build.
|
||||
|
||||
config TPL_SERIAL
|
||||
bool "Support serial"
|
||||
select TPL_PRINTF
|
||||
select TPL_STRTO
|
||||
help
|
||||
Enable support for serial in TPL. See SPL_SERIAL for
|
||||
details.
|
||||
|
||||
config TPL_SPI_FLASH_SUPPORT
|
||||
bool "Support SPI flash drivers"
|
||||
help
|
||||
Enable support for using SPI flash in TPL. See SPL_SPI_FLASH_SUPPORT
|
||||
for details.
|
||||
|
||||
config TPL_SPI_FLASH_TINY
|
||||
bool "Enable low footprint TPL SPI Flash support"
|
||||
depends on TPL_SPI_FLASH_SUPPORT && !SPI_FLASH_BAR
|
||||
default y if SPI_FLASH
|
||||
help
|
||||
Enable lightweight TPL SPI Flash support that supports just reading
|
||||
data/images from flash. No support to write/erase flash. Enable
|
||||
this if you have TPL size limitations and don't need full-fledged
|
||||
SPI flash support.
|
||||
|
||||
config TPL_SPI_LOAD
|
||||
bool "Support loading from SPI flash"
|
||||
depends on TPL_SPI_FLASH_SUPPORT
|
||||
help
|
||||
Enable support for loading next stage, U-Boot or otherwise, from
|
||||
SPI NOR in U-Boot TPL.
|
||||
|
||||
config TPL_SPI
|
||||
bool "Support SPI drivers"
|
||||
help
|
||||
Enable support for using SPI in TPL. See SPL_SPI for
|
||||
details.
|
||||
|
||||
config TPL_DM_SPI
|
||||
bool "Support SPI DM drivers in TPL"
|
||||
help
|
||||
Enable support for SPI DM drivers in TPL.
|
||||
|
||||
config TPL_DM_SPI_FLASH
|
||||
bool "Support SPI DM FLASH drivers in TPL"
|
||||
help
|
||||
Enable support for SPI DM flash drivers in TPL.
|
||||
|
||||
config TPL_YMODEM_SUPPORT
|
||||
bool "Support loading using Ymodem"
|
||||
depends on TPL_SERIAL
|
||||
help
|
||||
While loading from serial is slow it can be a useful backup when
|
||||
there is no other option. The Ymodem protocol provides a reliable
|
||||
means of transmitting U-Boot over a serial line for using in TPL,
|
||||
with a checksum to ensure correctness.
|
||||
|
||||
endif # TPL
|
||||
source "common/spl/Kconfig.tpl"
|
||||
|
||||
config VPL
|
||||
bool
|
||||
@ -1942,209 +1489,7 @@ config VPL
|
||||
If you want to build VPL as well as the normal image, TPL and SPL,
|
||||
say Y.
|
||||
|
||||
if VPL
|
||||
|
||||
config VPL_BANNER_PRINT
|
||||
bool "Enable output of the VPL banner 'U-Boot VPL ...'"
|
||||
depends on VPL
|
||||
default y
|
||||
help
|
||||
If this option is enabled, VPL will print the banner with version
|
||||
info. Disabling this option could be useful to reduce VPL boot time
|
||||
(e.g. approx. 6 ms faster, when output on i.MX6 with 115200 baud).
|
||||
|
||||
config VPL_BOARD_INIT
|
||||
bool "Call board-specific initialization in VPL"
|
||||
help
|
||||
If this option is enabled, U-Boot will call the function
|
||||
spl_board_init() from board_init_r(). This function should be
|
||||
provided by the board.
|
||||
|
||||
config VPL_CACHE
|
||||
depends on CACHE
|
||||
bool "Support cache drivers in VPL"
|
||||
help
|
||||
Enable support for cache drivers in VPL.
|
||||
|
||||
config VPL_CRC32
|
||||
bool "Support CRC32 in VPL"
|
||||
default y if VPL_ENV_SUPPORT || VPL_BLOBLIST
|
||||
help
|
||||
Enable this to support CRC32 in uImages or FIT images within VPL.
|
||||
This is a 32-bit checksum value that can be used to verify images.
|
||||
For FIT images, this is the least secure type of checksum, suitable
|
||||
for detected accidental image corruption. For secure applications you
|
||||
should consider SHA1 or SHA256.
|
||||
|
||||
config VPL_DM_SPI
|
||||
bool "Support SPI DM drivers in VPL"
|
||||
help
|
||||
Enable support for SPI DM drivers in VPL.
|
||||
|
||||
config VPL_DM_SPI_FLASH
|
||||
bool "Support SPI DM FLASH drivers in VPL"
|
||||
help
|
||||
Enable support for SPI DM flash drivers in VPL.
|
||||
|
||||
config VPL_FRAMEWORK
|
||||
bool "Support VPL based upon the common SPL framework"
|
||||
default y
|
||||
help
|
||||
Enable the SPL framework under common/spl/ for VPL builds.
|
||||
This framework supports MMC, NAND and YMODEM and other methods
|
||||
loading of U-Boot's next stage. If unsure, say Y.
|
||||
|
||||
config VPL_HANDOFF
|
||||
bool "Pass hand-off information from VPL to SPL"
|
||||
depends on HANDOFF && VPL_BLOBLIST
|
||||
default y
|
||||
help
|
||||
This option enables VPL to write handoff information. This can be
|
||||
used to pass information like the size of SDRAM from VPL to SPL. Also
|
||||
VPL can receive information from TPL in the same place if that is
|
||||
enabled.
|
||||
|
||||
config VPL_LIBCOMMON_SUPPORT
|
||||
bool "Support common libraries"
|
||||
default y if SPL_LIBCOMMON_SUPPORT
|
||||
help
|
||||
Enable support for common U-Boot libraries within VPL. See
|
||||
SPL_LIBCOMMON_SUPPORT for details.
|
||||
|
||||
config VPL_LIBGENERIC_SUPPORT
|
||||
bool "Support generic libraries"
|
||||
default y if SPL_LIBGENERIC_SUPPORT
|
||||
help
|
||||
Enable support for generic U-Boot libraries within VPL. These
|
||||
libraries include generic code to deal with device tree, hashing,
|
||||
printf(), compression and the like. This option is enabled on many
|
||||
boards. Enable this option to build the code in lib/ as part of a
|
||||
VPL build.
|
||||
|
||||
config VPL_DRIVERS_MISC
|
||||
bool "Support misc drivers"
|
||||
default y if TPL_DRIVERS_MISC
|
||||
help
|
||||
Enable miscellaneous drivers in VPL. These drivers perform various
|
||||
tasks that don't fall nicely into other categories, Enable this
|
||||
option to build the drivers in drivers/misc as part of a VPL
|
||||
build, for those that support building in VPL (not all drivers do).
|
||||
|
||||
config VPL_ENV_SUPPORT
|
||||
bool "Support an environment"
|
||||
help
|
||||
Enable environment support in VPL. The U-Boot environment provides
|
||||
a number of settings (essentially name/value pairs) which can
|
||||
control many aspects of U-Boot's operation. Enabling this option will
|
||||
make env_get() and env_set() available in VSPL.
|
||||
|
||||
config VPL_GPIO
|
||||
bool "Support GPIO in VPL"
|
||||
default y if SPL_GPIO
|
||||
help
|
||||
Enable support for GPIOs (General-purpose Input/Output) in VPL.
|
||||
GPIOs allow U-Boot to read the state of an input line (high or
|
||||
low) and set the state of an output line. This can be used to
|
||||
drive LEDs, control power to various system parts and read user
|
||||
input. GPIOs can be useful in VPL to enable a 'sign-of-life' LED,
|
||||
for example. Enable this option to build the drivers in
|
||||
drivers/gpio as part of a VPL build.
|
||||
|
||||
config VPL_HANDOFF
|
||||
bool "Pass hand-off information from VPL to SPL and U-Boot proper"
|
||||
depends on HANDOFF && VPL_BLOBLIST
|
||||
default y
|
||||
help
|
||||
This option enables VPL to write handoff information. This can be
|
||||
used to pass information like the size of SDRAM from VPL to U-Boot
|
||||
proper. The information is also available to VPL if it is useful
|
||||
there.
|
||||
|
||||
config VPL_HASH
|
||||
bool "Support hashing drivers in VPL"
|
||||
depends on VPL
|
||||
select SHA1
|
||||
select SHA256
|
||||
help
|
||||
Enable hashing drivers in VPL. These drivers can be used to
|
||||
accelerate secure boot processing in secure applications. Enable
|
||||
this option to build system-specific drivers for hash acceleration
|
||||
as part of a VPL build.
|
||||
|
||||
config VPL_I2C_SUPPORT
|
||||
bool "Support I2C in VPL"
|
||||
default y if SPL_I2C_SUPPORT
|
||||
help
|
||||
Enable support for the I2C bus in VPL. Vee SPL_I2C_SUPPORT for
|
||||
details.
|
||||
|
||||
config VPL_PCH_SUPPORT
|
||||
bool "Support PCH drivers"
|
||||
default y if TPL_PCH_SUPPORT
|
||||
help
|
||||
Enable support for PCH (Platform Controller Hub) devices in VPL.
|
||||
These are used to set up GPIOs and the SPI peripheral early in
|
||||
boot. This enables the drivers in drivers/pch as part of a VPL
|
||||
build.
|
||||
|
||||
config VPL_PCI
|
||||
bool "Support PCI drivers"
|
||||
default y if SPL_PCI
|
||||
help
|
||||
Enable support for PCI in VPL. For platforms that need PCI to boot,
|
||||
or must perform some init using PCI in VPL, this provides the
|
||||
necessary driver support. This enables the drivers in drivers/pci
|
||||
as part of a VPL build.
|
||||
|
||||
config VPL_RTC
|
||||
bool "Support RTC drivers"
|
||||
help
|
||||
Enable RTC (Real-time Clock) support in VPL. This includes support
|
||||
for reading and setting the time. Some RTC devices also have some
|
||||
non-volatile (battery-backed) memory which is accessible if
|
||||
needed. This enables the drivers in drivers/rtc as part of a VPL
|
||||
build.
|
||||
|
||||
config VPL_SERIAL
|
||||
bool "Support serial"
|
||||
default y if TPL_SERIAL
|
||||
select VPL_PRINTF
|
||||
select VPL_STRTO
|
||||
help
|
||||
Enable support for serial in VPL. See SPL_SERIAL_SUPPORT for
|
||||
details.
|
||||
|
||||
config VPL_SIZE_LIMIT
|
||||
hex "Maximum size of VPL image"
|
||||
depends on VPL
|
||||
default 0x0
|
||||
help
|
||||
Specifies the maximum length of the U-Boot VPL image.
|
||||
If this value is zero, it is ignored.
|
||||
|
||||
config VPL_SPI
|
||||
bool "Support SPI drivers"
|
||||
help
|
||||
Enable support for using SPI in VPL. See SPL_SPI_SUPPORT for
|
||||
details.
|
||||
|
||||
config VPL_SPI_FLASH_SUPPORT
|
||||
bool "Support SPI flash drivers"
|
||||
help
|
||||
Enable support for using SPI flash in VPL, and loading U-Boot from
|
||||
SPI flash. SPI flash (Serial Peripheral Bus flash) is named after
|
||||
the SPI bus that is used to connect it to a system. It is a simple
|
||||
but fast bidirectional 4-wire bus (clock, chip select and two data
|
||||
lines). This enables the drivers in drivers/mtd/spi as part of a
|
||||
VPL build. This normally requires VPL_SPI_SUPPORT.
|
||||
|
||||
config VPL_TEXT_BASE
|
||||
hex "VPL Text Base"
|
||||
default 0x0
|
||||
help
|
||||
The address in memory that VPL will be running from.
|
||||
|
||||
endif # VPL
|
||||
source "common/spl/Kconfig.vpl"
|
||||
|
||||
config SPL_AT91_MCK_BYPASS
|
||||
bool "Use external clock signal as a source of main clock for AT91 platforms"
|
||||
|
||||
124
common/spl/Kconfig.nxp
Normal file
124
common/spl/Kconfig.nxp
Normal file
@ -0,0 +1,124 @@
|
||||
menu "PowerPC and LayerScape SPL Boot options"
|
||||
depends on (PPC && SUPPORT_SPL && !SPL_FRAMEWORK) || \
|
||||
((ARCH_LS1021A || ARCH_LS1043A || ARCH_LS1046A) && SUPPORT_SPL)
|
||||
|
||||
config SPL_NAND_BOOT
|
||||
bool "Load SPL from NAND flash"
|
||||
depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_MMC_BOOT
|
||||
bool "Load SPL from SD Card / eMMC"
|
||||
depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_SPI_BOOT
|
||||
bool "Load SPL from SPI flash"
|
||||
depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_FSL_PBL
|
||||
bool "Create SPL in Freescale PBI format"
|
||||
depends on (PPC || ARCH_LS1021A || ARCH_LS1043A || ARCH_LS1046A) && \
|
||||
SUPPORT_SPL
|
||||
help
|
||||
Create boot binary having SPL binary in PBI format concatenated with
|
||||
u-boot binary.
|
||||
|
||||
config SPL_SYS_CCSR_DO_NOT_RELOCATE
|
||||
bool "Ensures that CCSR is not relocated"
|
||||
depends on PPC
|
||||
help
|
||||
If this is defined, then CONFIG_SYS_CCSRBAR_PHYS will be forced to a
|
||||
value that ensures that CCSR is not relocated.
|
||||
|
||||
config TPL_SYS_CCSR_DO_NOT_RELOCATE
|
||||
def_bool y
|
||||
depends on SPL_SYS_CCSR_DO_NOT_RELOCATE
|
||||
|
||||
menu "PowerPC SPL / TPL specific options"
|
||||
depends on PPC && (SPL && !SPL_FRAMEWORK)
|
||||
|
||||
config SPL_INIT_MINIMAL
|
||||
bool "Arch init code will be built for a very small image"
|
||||
|
||||
config SPL_FLUSH_IMAGE
|
||||
bool "Clean dcache and invalidate icache after loading the image"
|
||||
|
||||
config SPL_SKIP_RELOCATE
|
||||
bool "Skip relocating SPL"
|
||||
|
||||
config SPL_GD_ADDR
|
||||
hex "Address to use for global data (gd) in SPL"
|
||||
depends on !SPL_INIT_MINIMAL
|
||||
|
||||
config SPL_RELOC_TEXT_BASE
|
||||
hex "Address to relocate SPL to"
|
||||
default SPL_TEXT_BASE
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_SPL_TEXT_BASE (i.e. no
|
||||
relocation is done).
|
||||
|
||||
config SPL_RELOC_STACK
|
||||
hex "Address of the start of the stack SPL will use after relocation."
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_SYS_SPL_MALLOC_START. Starting
|
||||
address of the malloc pool used in SPL. When this option is set the full
|
||||
malloc is used in SPL and it is set up by spl_init() and before that, the
|
||||
simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.
|
||||
|
||||
config SPL_RELOC_MALLOC
|
||||
bool "SPL has malloc pool after relocation"
|
||||
|
||||
config SPL_RELOC_MALLOC_ADDR
|
||||
hex "Address of malloc pool in SPL"
|
||||
depends on SPL_RELOC_MALLOC
|
||||
|
||||
config SPL_RELOC_MALLOC_SIZE
|
||||
hex "Size of malloc pool in SPL"
|
||||
depends on SPL_RELOC_MALLOC
|
||||
|
||||
config TPL_GD_ADDR
|
||||
hex "Address to use for global data (gd) in TPL"
|
||||
depends on TPL
|
||||
|
||||
config TPL_RELOC_TEXT_BASE
|
||||
hex "Address to relocate TPL to"
|
||||
depends on TPL
|
||||
default TPL_TEXT_BASE
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_TPL_TEXT_BASE (i.e. no
|
||||
relocation is done).
|
||||
|
||||
config TPL_RELOC_STACK
|
||||
hex "Address of the start of the stack TPL will use after relocation."
|
||||
depends on TPL
|
||||
help
|
||||
If unspecified, this is equal to CONFIG_SYS_TPL_MALLOC_START. Starting
|
||||
address of the malloc pool used in TPL. When this option is set the full
|
||||
malloc is used in TPL and it is set up by spl_init() and before that, the
|
||||
simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.
|
||||
|
||||
config TPL_RELOC_MALLOC
|
||||
bool "TPL has malloc pool after relocation"
|
||||
depends on TPL
|
||||
|
||||
config TPL_RELOC_MALLOC_ADDR
|
||||
hex "Address of malloc pool in TPL"
|
||||
depends on TPL_RELOC_MALLOC
|
||||
|
||||
config TPL_RELOC_MALLOC_SIZE
|
||||
hex "Size of malloc pool in TPL"
|
||||
depends on TPL_RELOC_MALLOC
|
||||
|
||||
config TPL_PAD_TO
|
||||
hex "Offset to which the TPL should be padded before appending the TPL payload"
|
||||
depends on TPL && !TPL_FRAMEWORK
|
||||
default TPL_MAX_SIZE
|
||||
help
|
||||
Image offset to which the TPL should be padded before appending the
|
||||
TPL payload. By default, this is defined as CONFIG_TPL_MAX_SIZE, or 0 if
|
||||
CONFIG_TPL_MAX_SIZE is undefined. CONFIG_TPL_PAD_TO must be either
|
||||
0, meaning to append the TPL payload without any padding, or >=
|
||||
CONFIG_TPL_MAX_SIZE.
|
||||
endmenu
|
||||
|
||||
endmenu
|
||||
|
||||
322
common/spl/Kconfig.tpl
Normal file
322
common/spl/Kconfig.tpl
Normal file
@ -0,0 +1,322 @@
|
||||
menu "TPL configuration options"
|
||||
depends on TPL
|
||||
|
||||
config TPL_SIZE_LIMIT
|
||||
hex "Maximum size of TPL image"
|
||||
default 0x0
|
||||
help
|
||||
Specifies the maximum length of the U-Boot TPL image.
|
||||
If this value is zero, it is ignored.
|
||||
|
||||
config TPL_BINMAN_SYMBOLS
|
||||
bool "Declare binman symbols in TPL"
|
||||
depends on SPL_FRAMEWORK && BINMAN
|
||||
default y
|
||||
help
|
||||
This enables use of symbols in TPL which refer to U-Boot, enabling TPL
|
||||
to obtain the location of U-Boot simply by calling spl_get_image_pos()
|
||||
and spl_get_image_size().
|
||||
|
||||
For this to work, you must have a U-Boot image in the binman image, so
|
||||
binman can update TPL with the location of it.
|
||||
|
||||
config TPL_FRAMEWORK
|
||||
bool "Support TPL based upon the common SPL framework"
|
||||
default y if SPL_FRAMEWORK
|
||||
help
|
||||
Enable the SPL framework under common/spl/ for TPL builds.
|
||||
This framework supports MMC, NAND and YMODEM and other methods
|
||||
loading of U-Boot's SPL stage. If unsure, say Y.
|
||||
|
||||
config TPL_BANNER_PRINT
|
||||
bool "Enable output of the TPL banner 'U-Boot TPL ...'"
|
||||
default y
|
||||
help
|
||||
If this option is enabled, TPL will print the banner with version
|
||||
info. Disabling this option could be useful to reduce TPL boot time
|
||||
(e.g. approx. 6 ms faster, when output on i.MX6 with 115200 baud).
|
||||
|
||||
config TPL_HANDOFF
|
||||
bool "Pass hand-off information from TPL to SPL and U-Boot proper"
|
||||
depends on HANDOFF && TPL_BLOBLIST
|
||||
default y
|
||||
help
|
||||
This option enables TPL to write handoff information. This can be
|
||||
used to pass information like the size of SDRAM from TPL to U-Boot
|
||||
proper. The information is also available to SPL if it is useful
|
||||
there.
|
||||
|
||||
config TPL_BOARD_INIT
|
||||
bool "Call board-specific initialization in TPL"
|
||||
help
|
||||
If this option is enabled, U-Boot will call the function
|
||||
spl_board_init() from board_init_r(). This function should be
|
||||
provided by the board.
|
||||
|
||||
config TPL_BOOTCOUNT_LIMIT
|
||||
bool "Support bootcount in TPL"
|
||||
depends on TPL_ENV_SUPPORT
|
||||
help
|
||||
If this option is enabled, the TPL will support bootcount.
|
||||
For example, it may be useful to choose the device to boot.
|
||||
|
||||
config TPL_SYS_MALLOC_SIMPLE
|
||||
bool
|
||||
prompt "Only use malloc_simple functions in the TPL"
|
||||
help
|
||||
Say Y here to only use the *_simple malloc functions from
|
||||
malloc_simple.c, rather then using the versions from dlmalloc.c;
|
||||
this will make the TPL binary smaller at the cost of more heap
|
||||
usage as the *_simple malloc functions do not re-use free-ed mem.
|
||||
|
||||
config TPL_SEPARATE_BSS
|
||||
bool "BSS section is in a different memory region from text"
|
||||
default y if SPL_SEPARATE_BSS
|
||||
help
|
||||
Some platforms need a large BSS region in TPL and can provide this
|
||||
because RAM is already set up. In this case BSS can be moved to RAM.
|
||||
This option should then be enabled so that the correct device tree
|
||||
location is used. Normally we put the device tree at the end of BSS
|
||||
but with this option enabled, it goes at _image_binary_end.
|
||||
|
||||
config TPL_LDSCRIPT
|
||||
string "Linker script for the TPL stage"
|
||||
default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
|
||||
default "arch/\$(ARCH)/cpu/u-boot-spl.lds"
|
||||
help
|
||||
The TPL stage will usually require a different linker-script
|
||||
(as it runs from a different memory region) than the regular
|
||||
U-Boot stage. Set this to the path of the linker-script to
|
||||
be used for TPL.
|
||||
|
||||
May be left empty to trigger the Makefile infrastructure to
|
||||
fall back to the linker-script used for the SPL stage.
|
||||
|
||||
config TPL_NEEDS_SEPARATE_STACK
|
||||
bool "TPL needs a separate initial stack-pointer"
|
||||
help
|
||||
Enable, if the TPL stage should not inherit its initial
|
||||
stack-pointer from the settings for the SPL stage.
|
||||
|
||||
config TPL_POWER
|
||||
bool "Support power drivers"
|
||||
help
|
||||
Enable support for power control in TPL. This includes support
|
||||
for PMICs (Power-management Integrated Circuits) and some of the
|
||||
features provided by PMICs. In particular, voltage regulators can
|
||||
be used to enable/disable power and vary its voltage. That can be
|
||||
useful in TPL to turn on boot peripherals and adjust CPU voltage
|
||||
so that the clock speed can be increased. This enables the drivers
|
||||
in drivers/power, drivers/power/pmic and drivers/power/regulator
|
||||
as part of an TPL build.
|
||||
|
||||
config TPL_TEXT_BASE
|
||||
hex "Base address for the .text section of the TPL stage"
|
||||
default 0
|
||||
help
|
||||
The base address for the .text section of the TPL stage.
|
||||
|
||||
config TPL_MAX_SIZE
|
||||
hex "Maximum size (in bytes) for the TPL stage"
|
||||
default 0x2e000 if ROCKCHIP_RK3399
|
||||
default 0x8000 if ROCKCHIP_RK3288
|
||||
default 0x7000 if ROCKCHIP_RK322X || ROCKCHIP_RK3328 || ROCKCHIP_RK3368
|
||||
default 0x2800 if ROCKCHIP_PX30
|
||||
default 0x0
|
||||
help
|
||||
The maximum size (in bytes) of the TPL stage.
|
||||
|
||||
config TPL_STACK
|
||||
hex "Address of the initial stack-pointer for the TPL stage"
|
||||
depends on TPL_NEEDS_SEPARATE_STACK
|
||||
help
|
||||
The address of the initial stack-pointer for the TPL stage.
|
||||
Usually this will be the (aligned) top-of-stack.
|
||||
|
||||
config TPL_READ_ONLY
|
||||
bool
|
||||
depends on TPL_OF_PLATDATA
|
||||
select TPL_OF_PLATDATA_NO_BIND
|
||||
select TPL_OF_PLATDATA_RT
|
||||
help
|
||||
Some platforms (e.g. x86 Apollo Lake) load SPL into a read-only
|
||||
section of memory. This means that of-platdata must make a copy (in
|
||||
writeable memory) of anything it wants to modify, such as
|
||||
device-private data.
|
||||
|
||||
config TPL_BOOTROM_SUPPORT
|
||||
bool "Support returning to the BOOTROM (from TPL)"
|
||||
help
|
||||
Some platforms (e.g. the Rockchip RK3368) provide support in their
|
||||
ROM for loading the next boot-stage after performing basic setup
|
||||
from the TPL stage.
|
||||
|
||||
Enable this option, to return to the BOOTROM through the
|
||||
BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
|
||||
boot device list, if not implemented for a given board)
|
||||
|
||||
config TPL_CRC32
|
||||
bool "Support CRC32 in TPL"
|
||||
default y if TPL_ENV_SUPPORT || TPL_BLOBLIST
|
||||
help
|
||||
Enable this to support CRC32 in uImages or FIT images within SPL.
|
||||
This is a 32-bit checksum value that can be used to verify images.
|
||||
For FIT images, this is the least secure type of checksum, suitable
|
||||
for detected accidental image corruption. For secure applications you
|
||||
should consider SHA1 or SHA256.
|
||||
|
||||
config TPL_DRIVERS_MISC
|
||||
bool "Support misc drivers in TPL"
|
||||
help
|
||||
Enable miscellaneous drivers in TPL. These drivers perform various
|
||||
tasks that don't fall nicely into other categories, Enable this
|
||||
option to build the drivers in drivers/misc as part of an TPL
|
||||
build, for those that support building in TPL (not all drivers do).
|
||||
|
||||
config TPL_ENV_SUPPORT
|
||||
bool "Support an environment"
|
||||
help
|
||||
Enable environment support in TPL. See SPL_ENV_SUPPORT for details.
|
||||
|
||||
config TPL_GPIO
|
||||
bool "Support GPIO in TPL"
|
||||
help
|
||||
Enable support for GPIOs (General-purpose Input/Output) in TPL.
|
||||
GPIOs allow U-Boot to read the state of an input line (high or
|
||||
low) and set the state of an output line. This can be used to
|
||||
drive LEDs, control power to various system parts and read user
|
||||
input. GPIOs can be useful in TPL to enable a 'sign-of-life' LED,
|
||||
for example. Enable this option to build the drivers in
|
||||
drivers/gpio as part of an TPL build.
|
||||
|
||||
config TPL_I2C
|
||||
bool "Support I2C"
|
||||
help
|
||||
Enable support for the I2C bus in TPL. See SPL_I2C for
|
||||
details.
|
||||
|
||||
config TPL_LIBCOMMON_SUPPORT
|
||||
bool "Support common libraries"
|
||||
help
|
||||
Enable support for common U-Boot libraries within TPL. See
|
||||
SPL_LIBCOMMON_SUPPORT for details.
|
||||
|
||||
config TPL_LIBGENERIC_SUPPORT
|
||||
bool "Support generic libraries"
|
||||
help
|
||||
Enable support for generic U-Boot libraries within TPL. See
|
||||
SPL_LIBGENERIC_SUPPORT for details.
|
||||
|
||||
config TPL_MPC8XXX_INIT_DDR
|
||||
bool "Support MPC8XXX DDR init"
|
||||
help
|
||||
Enable support for DDR-SDRAM on the MPC8XXX family within TPL. See
|
||||
SPL_MPC8XXX_INIT_DDR for details.
|
||||
|
||||
config TPL_MMC
|
||||
bool "Support MMC"
|
||||
depends on MMC
|
||||
help
|
||||
Enable support for MMC within TPL. See SPL_MMC for details.
|
||||
|
||||
config TPL_NAND_SUPPORT
|
||||
bool "Support NAND flash"
|
||||
help
|
||||
Enable support for NAND in TPL. See SPL_NAND_SUPPORT for details.
|
||||
|
||||
config TPL_PCI
|
||||
bool "Support PCI drivers"
|
||||
help
|
||||
Enable support for PCI in TPL. For platforms that need PCI to boot,
|
||||
or must perform some init using PCI in SPL, this provides the
|
||||
necessary driver support. This enables the drivers in drivers/pci
|
||||
as part of a TPL build.
|
||||
|
||||
config TPL_PCH
|
||||
bool "Support PCH drivers"
|
||||
help
|
||||
Enable support for PCH (Platform Controller Hub) devices in TPL.
|
||||
These are used to set up GPIOs and the SPI peripheral early in
|
||||
boot. This enables the drivers in drivers/pch as part of a TPL
|
||||
build.
|
||||
|
||||
config TPL_RAM_SUPPORT
|
||||
bool "Support booting from RAM"
|
||||
help
|
||||
Enable booting of an image in RAM. The image can be preloaded or
|
||||
it can be loaded by TPL directly into RAM (e.g. using USB).
|
||||
|
||||
config TPL_RAM_DEVICE
|
||||
bool "Support booting from preloaded image in RAM"
|
||||
depends on TPL_RAM_SUPPORT
|
||||
help
|
||||
Enable booting of an image already loaded in RAM. The image has to
|
||||
be already in memory when TPL takes over, e.g. loaded by the boot
|
||||
ROM.
|
||||
|
||||
config TPL_RTC
|
||||
bool "Support RTC drivers"
|
||||
help
|
||||
Enable RTC (Real-time Clock) support in TPL. This includes support
|
||||
for reading and setting the time. Some RTC devices also have some
|
||||
non-volatile (battery-backed) memory which is accessible if
|
||||
needed. This enables the drivers in drivers/rtc as part of an TPL
|
||||
build.
|
||||
|
||||
config TPL_SERIAL
|
||||
bool "Support serial"
|
||||
select TPL_PRINTF
|
||||
select TPL_STRTO
|
||||
help
|
||||
Enable support for serial in TPL. See SPL_SERIAL for
|
||||
details.
|
||||
|
||||
config TPL_SPI_FLASH_SUPPORT
|
||||
bool "Support SPI flash drivers"
|
||||
help
|
||||
Enable support for using SPI flash in TPL. See SPL_SPI_FLASH_SUPPORT
|
||||
for details.
|
||||
|
||||
config TPL_SPI_FLASH_TINY
|
||||
bool "Enable low footprint TPL SPI Flash support"
|
||||
depends on TPL_SPI_FLASH_SUPPORT && !SPI_FLASH_BAR
|
||||
default y if SPI_FLASH
|
||||
help
|
||||
Enable lightweight TPL SPI Flash support that supports just reading
|
||||
data/images from flash. No support to write/erase flash. Enable
|
||||
this if you have TPL size limitations and don't need full-fledged
|
||||
SPI flash support.
|
||||
|
||||
config TPL_SPI_LOAD
|
||||
bool "Support loading from SPI flash"
|
||||
depends on TPL_SPI_FLASH_SUPPORT
|
||||
help
|
||||
Enable support for loading next stage, U-Boot or otherwise, from
|
||||
SPI NOR in U-Boot TPL.
|
||||
|
||||
config TPL_SPI
|
||||
bool "Support SPI drivers"
|
||||
help
|
||||
Enable support for using SPI in TPL. See SPL_SPI for
|
||||
details.
|
||||
|
||||
config TPL_DM_SPI
|
||||
bool "Support SPI DM drivers in TPL"
|
||||
help
|
||||
Enable support for SPI DM drivers in TPL.
|
||||
|
||||
config TPL_DM_SPI_FLASH
|
||||
bool "Support SPI DM FLASH drivers in TPL"
|
||||
help
|
||||
Enable support for SPI DM flash drivers in TPL.
|
||||
|
||||
config TPL_YMODEM_SUPPORT
|
||||
bool "Support loading using Ymodem"
|
||||
depends on TPL_SERIAL
|
||||
help
|
||||
While loading from serial is slow it can be a useful backup when
|
||||
there is no other option. The Ymodem protocol provides a reliable
|
||||
means of transmitting U-Boot over a serial line for using in TPL,
|
||||
with a checksum to ensure correctness.
|
||||
|
||||
endmenu
|
||||
201
common/spl/Kconfig.vpl
Normal file
201
common/spl/Kconfig.vpl
Normal file
@ -0,0 +1,201 @@
|
||||
menu "VPL options"
|
||||
depends on VPL
|
||||
|
||||
config VPL_BANNER_PRINT
|
||||
bool "Enable output of the VPL banner 'U-Boot VPL ...'"
|
||||
default y
|
||||
help
|
||||
If this option is enabled, VPL will print the banner with version
|
||||
info. Disabling this option could be useful to reduce VPL boot time
|
||||
(e.g. approx. 6 ms faster, when output on i.MX6 with 115200 baud).
|
||||
|
||||
config VPL_BOARD_INIT
|
||||
bool "Call board-specific initialization in VPL"
|
||||
help
|
||||
If this option is enabled, U-Boot will call the function
|
||||
spl_board_init() from board_init_r(). This function should be
|
||||
provided by the board.
|
||||
|
||||
config VPL_CACHE
|
||||
depends on CACHE
|
||||
bool "Support cache drivers in VPL"
|
||||
help
|
||||
Enable support for cache drivers in VPL.
|
||||
|
||||
config VPL_CRC32
|
||||
bool "Support CRC32 in VPL"
|
||||
default y if VPL_ENV_SUPPORT || VPL_BLOBLIST
|
||||
help
|
||||
Enable this to support CRC32 in uImages or FIT images within VPL.
|
||||
This is a 32-bit checksum value that can be used to verify images.
|
||||
For FIT images, this is the least secure type of checksum, suitable
|
||||
for detected accidental image corruption. For secure applications you
|
||||
should consider SHA1 or SHA256.
|
||||
|
||||
config VPL_DM_SPI
|
||||
bool "Support SPI DM drivers in VPL"
|
||||
help
|
||||
Enable support for SPI DM drivers in VPL.
|
||||
|
||||
config VPL_DM_SPI_FLASH
|
||||
bool "Support SPI DM FLASH drivers in VPL"
|
||||
help
|
||||
Enable support for SPI DM flash drivers in VPL.
|
||||
|
||||
config VPL_FRAMEWORK
|
||||
bool "Support VPL based upon the common SPL framework"
|
||||
default y
|
||||
help
|
||||
Enable the SPL framework under common/spl/ for VPL builds.
|
||||
This framework supports MMC, NAND and YMODEM and other methods
|
||||
loading of U-Boot's next stage. If unsure, say Y.
|
||||
|
||||
config VPL_HANDOFF
|
||||
bool "Pass hand-off information from VPL to SPL"
|
||||
depends on HANDOFF && VPL_BLOBLIST
|
||||
default y
|
||||
help
|
||||
This option enables VPL to write handoff information. This can be
|
||||
used to pass information like the size of SDRAM from VPL to SPL. Also
|
||||
VPL can receive information from TPL in the same place if that is
|
||||
enabled.
|
||||
|
||||
config VPL_LIBCOMMON_SUPPORT
|
||||
bool "Support common libraries"
|
||||
default y if SPL_LIBCOMMON_SUPPORT
|
||||
help
|
||||
Enable support for common U-Boot libraries within VPL. See
|
||||
SPL_LIBCOMMON_SUPPORT for details.
|
||||
|
||||
config VPL_LIBGENERIC_SUPPORT
|
||||
bool "Support generic libraries"
|
||||
default y if SPL_LIBGENERIC_SUPPORT
|
||||
help
|
||||
Enable support for generic U-Boot libraries within VPL. These
|
||||
libraries include generic code to deal with device tree, hashing,
|
||||
printf(), compression and the like. This option is enabled on many
|
||||
boards. Enable this option to build the code in lib/ as part of a
|
||||
VPL build.
|
||||
|
||||
config VPL_DRIVERS_MISC
|
||||
bool "Support misc drivers"
|
||||
default y if TPL_DRIVERS_MISC
|
||||
help
|
||||
Enable miscellaneous drivers in VPL. These drivers perform various
|
||||
tasks that don't fall nicely into other categories, Enable this
|
||||
option to build the drivers in drivers/misc as part of a VPL
|
||||
build, for those that support building in VPL (not all drivers do).
|
||||
|
||||
config VPL_ENV_SUPPORT
|
||||
bool "Support an environment"
|
||||
help
|
||||
Enable environment support in VPL. The U-Boot environment provides
|
||||
a number of settings (essentially name/value pairs) which can
|
||||
control many aspects of U-Boot's operation. Enabling this option will
|
||||
make env_get() and env_set() available in VSPL.
|
||||
|
||||
config VPL_GPIO
|
||||
bool "Support GPIO in VPL"
|
||||
default y if SPL_GPIO
|
||||
help
|
||||
Enable support for GPIOs (General-purpose Input/Output) in VPL.
|
||||
GPIOs allow U-Boot to read the state of an input line (high or
|
||||
low) and set the state of an output line. This can be used to
|
||||
drive LEDs, control power to various system parts and read user
|
||||
input. GPIOs can be useful in VPL to enable a 'sign-of-life' LED,
|
||||
for example. Enable this option to build the drivers in
|
||||
drivers/gpio as part of a VPL build.
|
||||
|
||||
config VPL_HANDOFF
|
||||
bool "Pass hand-off information from VPL to SPL and U-Boot proper"
|
||||
depends on HANDOFF && VPL_BLOBLIST
|
||||
default y
|
||||
help
|
||||
This option enables VPL to write handoff information. This can be
|
||||
used to pass information like the size of SDRAM from VPL to U-Boot
|
||||
proper. The information is also available to VPL if it is useful
|
||||
there.
|
||||
|
||||
config VPL_HASH
|
||||
bool "Support hashing drivers in VPL"
|
||||
select SHA1
|
||||
select SHA256
|
||||
help
|
||||
Enable hashing drivers in VPL. These drivers can be used to
|
||||
accelerate secure boot processing in secure applications. Enable
|
||||
this option to build system-specific drivers for hash acceleration
|
||||
as part of a VPL build.
|
||||
|
||||
config VPL_I2C_SUPPORT
|
||||
bool "Support I2C in VPL"
|
||||
default y if SPL_I2C_SUPPORT
|
||||
help
|
||||
Enable support for the I2C bus in VPL. Vee SPL_I2C_SUPPORT for
|
||||
details.
|
||||
|
||||
config VPL_PCH_SUPPORT
|
||||
bool "Support PCH drivers"
|
||||
default y if TPL_PCH_SUPPORT
|
||||
help
|
||||
Enable support for PCH (Platform Controller Hub) devices in VPL.
|
||||
These are used to set up GPIOs and the SPI peripheral early in
|
||||
boot. This enables the drivers in drivers/pch as part of a VPL
|
||||
build.
|
||||
|
||||
config VPL_PCI
|
||||
bool "Support PCI drivers"
|
||||
default y if SPL_PCI
|
||||
help
|
||||
Enable support for PCI in VPL. For platforms that need PCI to boot,
|
||||
or must perform some init using PCI in VPL, this provides the
|
||||
necessary driver support. This enables the drivers in drivers/pci
|
||||
as part of a VPL build.
|
||||
|
||||
config VPL_RTC
|
||||
bool "Support RTC drivers"
|
||||
help
|
||||
Enable RTC (Real-time Clock) support in VPL. This includes support
|
||||
for reading and setting the time. Some RTC devices also have some
|
||||
non-volatile (battery-backed) memory which is accessible if
|
||||
needed. This enables the drivers in drivers/rtc as part of a VPL
|
||||
build.
|
||||
|
||||
config VPL_SERIAL
|
||||
bool "Support serial"
|
||||
default y if TPL_SERIAL
|
||||
select VPL_PRINTF
|
||||
select VPL_STRTO
|
||||
help
|
||||
Enable support for serial in VPL. See SPL_SERIAL_SUPPORT for
|
||||
details.
|
||||
|
||||
config VPL_SIZE_LIMIT
|
||||
hex "Maximum size of VPL image"
|
||||
default 0x0
|
||||
help
|
||||
Specifies the maximum length of the U-Boot VPL image.
|
||||
If this value is zero, it is ignored.
|
||||
|
||||
config VPL_SPI
|
||||
bool "Support SPI drivers"
|
||||
help
|
||||
Enable support for using SPI in VPL. See SPL_SPI_SUPPORT for
|
||||
details.
|
||||
|
||||
config VPL_SPI_FLASH_SUPPORT
|
||||
bool "Support SPI flash drivers"
|
||||
help
|
||||
Enable support for using SPI flash in VPL, and loading U-Boot from
|
||||
SPI flash. SPI flash (Serial Peripheral Bus flash) is named after
|
||||
the SPI bus that is used to connect it to a system. It is a simple
|
||||
but fast bidirectional 4-wire bus (clock, chip select and two data
|
||||
lines). This enables the drivers in drivers/mtd/spi as part of a
|
||||
VPL build. This normally requires VPL_SPI_SUPPORT.
|
||||
|
||||
config VPL_TEXT_BASE
|
||||
hex "VPL Text Base"
|
||||
default 0x0
|
||||
help
|
||||
The address in memory that VPL will be running from.
|
||||
|
||||
endmenu
|
||||
Loading…
Reference in New Issue
Block a user