leandrof/u-boot
1
0
Fork 1
Code Issues Pull Requests Packages Projects Releases Wiki Activity

powerpc/b4860qds: Added Support for B4860QDS

Browse Source 
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
  ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,  ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
  16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
  8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
  RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
  connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
  connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
  configuration reset source. The RCW source is set by appropriate
  DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
	- On-board eCWTAP controller with ETH and USB I/F
	- JTAG/COP 16-pin header for any external TAP controller
	- External JTAG source over AMC to support B2B configuration
	- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
	- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
  DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
  - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This commit is contained in:
York Sun
2012-12-23 19:25:27 +00:00
committed by Andy Fleming
parent db9a807054
commit b5b06fb7b0
13 changed files with 2536 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files

54
board/freescale/b4860qds/Makefile Normal file
View File

@@ -0,0 +1,54 @@
#
# Copyright 2012 Freescale Semiconductor, Inc.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
COBJS-y += $(BOARD).o
COBJS-y += ddr.o
COBJS-$(CONFIG_B4860QDS)+= eth_b4860qds.o
COBJS-$(CONFIG_PCI) += pci.o
COBJS-y += law.o
COBJS-y += tlb.o
SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS-y))
SOBJS := $(addprefix $(obj),$(SOBJS))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
$(call cmd_link_o_target, $(OBJS))
clean:
rm -f $(OBJS) $(SOBJS)
distclean: clean
rm -f $(LIB) core *.bak .depend
#########################################################################
# defines $(obj).depend target
include $(SRCTREE)/rules.mk
sinclude $(obj).depend
#########################################################################

458
board/freescale/b4860qds/b4860qds.c Normal file
View File

@@ -0,0 +1,458 @@
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <command.h>
#include <i2c.h>
#include <netdev.h>
#include <linux/compiler.h>
#include <asm/mmu.h>
#include <asm/processor.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_portals.h>
#include <asm/fsl_liodn.h>
#include <fm_eth.h>
#include "../common/qixis.h"
#include "../common/vsc3316_3308.h"
#include "b4860qds.h"
#include "b4860qds_qixis.h"
#include "b4860qds_crossbar_con.h"
#define CLK_MUX_SEL_MASK 0x4
#define ETH_PHY_CLK_OUT 0x4
DECLARE_GLOBAL_DATA_PTR;
int checkboard(void)
{
char buf[64];
u8 sw;
struct cpu_type *cpu = gd->cpu;
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
unsigned int i;
static const char *const freq[] = {"100", "125", "156.25", "161.13",
"122.88", "122.88", "122.88"};
int clock;
printf("Board: %sQDS, ", cpu->name);
printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ",
QIXIS_READ(id), QIXIS_READ(arch));
sw = QIXIS_READ(brdcfg[0]);
sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
if (sw < 0x8)
printf("vBank: %d\n", sw);
else if (sw >= 0x8 && sw <= 0xE)
puts("NAND\n");
else
printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
printf("FPGA: v%d (%s), build %d",
(int)QIXIS_READ(scver), qixis_read_tag(buf),
(int)qixis_read_minor());
/* the timestamp string contains "\n" at the end */
printf(" on %s", qixis_read_time(buf));
/* Display the RCW, so that no one gets confused as to what RCW
* we're actually using for this boot.
*/
puts("Reset Configuration Word (RCW):");
for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
u32 rcw = in_be32(&gur->rcwsr[i]);
if ((i % 4) == 0)
printf("\n %08x:", i * 4);
printf(" %08x", rcw);
}
puts("\n");
/*
* Display the actual SERDES reference clocks as configured by the
* dip switches on the board. Note that the SWx registers could
* technically be set to force the reference clocks to match the
* values that the SERDES expects (or vice versa). For now, however,
* we just display both values and hope the user notices when they
* don't match.
*/
puts("SERDES Reference Clocks: ");
sw = QIXIS_READ(brdcfg[2]);
clock = (sw >> 5) & 7;
printf("Bank1=%sMHz ", freq[clock]);
sw = QIXIS_READ(brdcfg[4]);
clock = (sw >> 6) & 3;
printf("Bank2=%sMHz\n", freq[clock]);
return 0;
}
int select_i2c_ch_pca(u8 ch)
{
int ret;
/* Selecting proper channel via PCA*/
ret = i2c_write(I2C_MUX_PCA_ADDR, 0x0, 1, &ch, 1);
if (ret) {
printf("PCA: failed to select proper channel.\n");
return ret;
}
return 0;
}
int configure_vsc3316_3308(void)
{
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
unsigned int num_vsc16_con, num_vsc08_con;
u32 serdes1_prtcl, serdes2_prtcl;
int ret;
serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
if (!serdes1_prtcl) {
printf("SERDES1 is not enabled\n");
return 0;
}
serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl);
serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
if (!serdes2_prtcl) {
printf("SERDES2 is not enabled\n");
return 0;
}
serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl);
switch (serdes1_prtcl) {
case 0x2a:
case 0x2C:
case 0x2D:
case 0x2E:
/*
* Configuration:
* SERDES: 1
* Lanes: A,B: SGMII
* Lanes: C,D,E,F,G,H: CPRI
*/
debug("Configuring crossbar to use onboard SGMII PHYs:"
"srds_prctl:%x\n", serdes1_prtcl);
num_vsc16_con = NUM_CON_VSC3316;
/* Configure VSC3316 crossbar switch */
ret = select_i2c_ch_pca(I2C_CH_VSC3316);
if (!ret) {
ret = vsc3316_config(VSC3316_TX_ADDRESS,
vsc16_tx_sgmii_lane_ab, num_vsc16_con);
if (ret)
return ret;
ret = vsc3316_config(VSC3316_RX_ADDRESS,
vsc16_rx_sgmii_lane_ab, num_vsc16_con);
if (ret)
return ret;
} else {
return ret;
}
break;
#ifdef CONFIG_PPC_B4420
case 0x18:
/*
* Configuration:
* SERDES: 1
* Lanes: A,B,C,D: SGMII
* Lanes: E,F,G,H: CPRI
*/
debug("Configuring crossbar to use onboard SGMII PHYs:"
"srds_prctl:%x\n", serdes1_prtcl);
num_vsc16_con = NUM_CON_VSC3316;
/* Configure VSC3316 crossbar switch */
ret = select_i2c_ch_pca(I2C_CH_VSC3316);
if (!ret) {
ret = vsc3316_config(VSC3316_TX_ADDRESS,
vsc16_tx_sgmii_lane_cd, num_vsc16_con);
if (ret)
return ret;
ret = vsc3316_config(VSC3316_RX_ADDRESS,
vsc16_rx_sgmii_lane_cd, num_vsc16_con);
if (ret)
return ret;
} else {
return ret;
}
break;
#endif
case 0x3E:
case 0x0D:
case 0x0E:
case 0x12:
num_vsc16_con = NUM_CON_VSC3316;
/* Configure VSC3316 crossbar switch */
ret = select_i2c_ch_pca(I2C_CH_VSC3316);
if (!ret) {
ret = vsc3316_config(VSC3316_TX_ADDRESS,
vsc16_tx_sfp, num_vsc16_con);
if (ret)
return ret;
ret = vsc3316_config(VSC3316_RX_ADDRESS,
vsc16_rx_sfp, num_vsc16_con);
if (ret)
return ret;
} else {
return ret;
}
break;
default:
printf("WARNING:VSC crossbars programming not supported for:%x"
" SerDes1 Protocol.\n", serdes1_prtcl);
return -1;
}
switch (serdes2_prtcl) {
case 0x9E:
case 0x9A:
case 0x98:
case 0xb2:
case 0x49:
case 0x4E:
case 0x8D:
case 0x7A:
num_vsc08_con = NUM_CON_VSC3308;
/* Configure VSC3308 crossbar switch */
ret = select_i2c_ch_pca(I2C_CH_VSC3308);
if (!ret) {
ret = vsc3308_config(VSC3308_TX_ADDRESS,
vsc08_tx_amc, num_vsc08_con);
if (ret)
return ret;
ret = vsc3308_config(VSC3308_RX_ADDRESS,
vsc08_rx_amc, num_vsc08_con);
if (ret)
return ret;
} else {
return ret;
}
break;
default:
printf("WARNING:VSC crossbars programming not supported for: %x"
" SerDes2 Protocol.\n", serdes2_prtcl);
return -1;
}
return 0;
}
int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
/*
* Remap Boot flash + PROMJET region to caching-inhibited
* so that flash can be erased properly.
*/
/* Flush d-cache and invalidate i-cache of any FLASH data */
flush_dcache();
invalidate_icache();
/* invalidate existing TLB entry for flash + promjet */
disable_tlb(flash_esel);
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, flash_esel, BOOKE_PAGESZ_256M, 1);
set_liodns();
#ifdef CONFIG_SYS_DPAA_QBMAN
setup_portals();
#endif
/* Configure VSC3316 and VSC3308 crossbar switches */
if (configure_vsc3316_3308())
printf("VSC:failed to configure VSC3316/3308.\n");
else
printf("VSC:VSC3316/3308 successfully configured.\n");
select_i2c_ch_pca(I2C_CH_DEFAULT);
return 0;
}
unsigned long get_board_sys_clk(void)
{
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
switch ((sysclk_conf & 0x0C) >> 2) {
case QIXIS_CLK_100:
return 100000000;
case QIXIS_CLK_125:
return 125000000;
case QIXIS_CLK_133:
return 133333333;
}
return 66666666;
}
unsigned long get_board_ddr_clk(void)
{
u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
switch (ddrclk_conf & 0x03) {
case QIXIS_CLK_100:
return 100000000;
case QIXIS_CLK_125:
return 125000000;
case QIXIS_CLK_133:
return 133333333;
}
return 66666666;
}
static int serdes_refclock(u8 sw, u8 sdclk)
{
unsigned int clock;
int ret = -1;
u8 brdcfg4;
if (sdclk == 1) {
brdcfg4 = QIXIS_READ(brdcfg[4]);
if ((brdcfg4 & CLK_MUX_SEL_MASK) == ETH_PHY_CLK_OUT)
return SRDS_PLLCR0_RFCK_SEL_125;
else
clock = (sw >> 5) & 7;
} else
clock = (sw >> 6) & 3;
switch (clock) {
case 0:
ret = SRDS_PLLCR0_RFCK_SEL_100;
break;
case 1:
ret = SRDS_PLLCR0_RFCK_SEL_125;
break;
case 2:
ret = SRDS_PLLCR0_RFCK_SEL_156_25;
break;
case 3:
ret = SRDS_PLLCR0_RFCK_SEL_161_13;
break;
case 4:
case 5:
case 6:
ret = SRDS_PLLCR0_RFCK_SEL_122_88;
break;
default:
ret = -1;
break;
}
return ret;
}
static const char *serdes_clock_to_string(u32 clock)
{
switch (clock) {
case SRDS_PLLCR0_RFCK_SEL_100:
return "100";
case SRDS_PLLCR0_RFCK_SEL_125:
return "125";
case SRDS_PLLCR0_RFCK_SEL_156_25:
return "156.25";
case SRDS_PLLCR0_RFCK_SEL_161_13:
return "161.13";
default:
return "122.88";
}
}
#define NUM_SRDS_BANKS 2
int misc_init_r(void)
{
u8 sw;
serdes_corenet_t *srds_regs =
(void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
u32 actual[NUM_SRDS_BANKS];
unsigned int i;
int clock;
sw = QIXIS_READ(brdcfg[2]);
clock = serdes_refclock(sw, 1);
if (clock >= 0)
actual[0] = clock;
else
printf("Warning: SDREFCLK1 switch setting is unsupported\n");
sw = QIXIS_READ(brdcfg[4]);
clock = serdes_refclock(sw, 2);
if (clock >= 0)
actual[1] = clock;
else
printf("Warning: SDREFCLK2 switch setting unsupported\n");
for (i = 0; i < NUM_SRDS_BANKS; i++) {
u32 pllcr0 = srds_regs->bank[i].pllcr0;
u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
if (expected != actual[i]) {
printf("Warning: SERDES bank %u expects reference clock"
" %sMHz, but actual is %sMHz\n", i + 1,
serdes_clock_to_string(expected),
serdes_clock_to_string(actual[i]));
}
}
return 0;
}
void ft_board_setup(void *blob, bd_t *bd)
{
phys_addr_t base;
phys_size_t size;
ft_cpu_setup(blob, bd);
base = getenv_bootm_low();
size = getenv_bootm_size();
fdt_fixup_memory(blob, (u64)base, (u64)size);
#ifdef CONFIG_PCI
pci_of_setup(blob, bd);
#endif
fdt_fixup_liodn(blob);
#ifdef CONFIG_HAS_FSL_DR_USB
fdt_fixup_dr_usb(blob, bd);
#endif
#ifdef CONFIG_SYS_DPAA_FMAN
fdt_fixup_fman_ethernet(blob);
fdt_fixup_board_enet(blob);
#endif
}

26
board/freescale/b4860qds/b4860qds.h Normal file
View File

@@ -0,0 +1,26 @@
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CORENET_DS_H__
#define __CORENET_DS_H__
void fdt_fixup_board_enet(void *blob);
void pci_of_setup(void *blob, bd_t *bd);
#endif

67
board/freescale/b4860qds/b4860qds_crossbar_con.h Normal file
View File

@@ -0,0 +1,67 @@
/*
* Copyright 2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CROSSBAR_CONNECTIONS_H__
#define __CROSSBAR_CONNECTIONS_H__
#define NUM_CON_VSC3316 8
#define NUM_CON_VSC3308 4
static const int8_t vsc16_tx_amc[8][2] = { {15, 3}, {0, 2}, {7, 4}, {9, 10},
{5, 11}, {4, 5}, {2, 6}, {12, 9} };
static const int8_t vsc16_tx_sfp[8][2] = { {15, 8}, {0, 0}, {7, 7}, {9, 1},
{5, 15}, {4, 14}, {2, 12}, {12, 13} };
static const int8_t vsc16_tx_sgmii_lane_ab[8][2] = { {2, 14}, {12, 15},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
#ifdef CONFIG_PPC_B4420
static const int8_t vsc16_tx_sgmii_lane_cd[8][2] = { {5, 14}, {4, 15},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
#endif
static const int8_t vsc16_tx_aurora[8][2] = { {2, 13}, {12, 12}, {-1, -1},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
static const int8_t vsc16_rx_amc[8][2] = { {3, 15}, {2, 1}, {4, 8}, {10, 9},
{11, 11}, {5, 10}, {6, 3}, {9, 12} };
static const int8_t vsc16_rx_sfp[8][2] = { {0, 15}, {8, 1}, {1, 8}, {7, 9},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
static const int8_t vsc16_rx_sgmii_lane_ab[8][2] = { {14, 3}, {15, 12},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
#ifdef CONFIG_PPC_B4420
static const int8_t vsc16_rx_sgmii_lane_cd[8][2] = { {14, 11}, {15, 10},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
#endif
static const int8_t vsc16_rx_aurora[8][2] = { {12, 3}, {13, 12}, {-1, -1},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
static const int8_t vsc08_tx_amc[4][2] = { {2, 2}, {3, 3}, {7, 4}, {1, 5} };
static const int8_t vsc08_tx_sfp[4][2] = { {2, 6}, {3, 7}, {7, 1}, {1, 0} };
static const int8_t vsc08_rx_amc[4][2] = { {2, 3}, {3, 4}, {4, 7}, {5, 1} };
static const int8_t vsc08_rx_sfp[4][2] = { {6, 3}, {7, 4}, {1, 7}, {0, 1} };
#endif

37
board/freescale/b4860qds/b4860qds_qixis.h Normal file
View File

@@ -0,0 +1,37 @@
/*
* Copyright 2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __B4860QDS_QIXIS_H__
#define __B4860QDS_QIXIS_H__
/* Definitions of QIXIS Registers for B4860QDS */
/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
#define BRDCFG4_EMISEL_MASK 0xE0
#define BRDCFG4_EMISEL_SHIFT 5
/* CLK */
#define QIXIS_CLK_66 0x0
#define QIXIS_CLK_100 0x1
#define QIXIS_CLK_125 0x2
#define QIXIS_CLK_133 0x3
#define QIXIS_SRDS1CLK_122 0x5a
#define QIXIS_SRDS1CLK_125 0x5e
#endif

190
board/freescale/b4860qds/ddr.c Normal file
View File

@@ -0,0 +1,190 @@
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 or later as published by the Free Software Foundation.
*/
#include <common.h>
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
DECLARE_GLOBAL_DATA_PTR;
dimm_params_t ddr_raw_timing = {
.n_ranks = 2,
.rank_density = 2147483648u,
.capacity = 4294967296u,
.primary_sdram_width = 64,
.ec_sdram_width = 8,
.registered_dimm = 0,
.mirrored_dimm = 1,
.n_row_addr = 15,
.n_col_addr = 10,
.n_banks_per_sdram_device = 8,
.edc_config = 2, /* ECC */
.burst_lengths_bitmask = 0x0c,
.tCKmin_X_ps = 1071,
.caslat_X = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */
.tAA_ps = 13910,
.tWR_ps = 15000,
.tRCD_ps = 13910,
.tRRD_ps = 6000,
.tRP_ps = 13910,
.tRAS_ps = 34000,
.tRC_ps = 48910,
.tRFC_ps = 260000,
.tWTR_ps = 7500,
.tRTP_ps = 7500,
.refresh_rate_ps = 7800000,
.tFAW_ps = 35000,
};
int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
unsigned int controller_number,
unsigned int dimm_number)
{
const char dimm_model[] = "RAW timing DDR";
if ((controller_number == 0) && (dimm_number == 0)) {
memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
}
return 0;
}
struct board_specific_parameters {
u32 n_ranks;
u32 datarate_mhz_high;
u32 clk_adjust;
u32 wrlvl_start;
u32 wrlvl_ctl_2;
u32 wrlvl_ctl_3;
u32 cpo;
u32 write_data_delay;
u32 force_2T;
};
/*
* This table contains all valid speeds we want to override with board
* specific parameters. datarate_mhz_high values need to be in ascending order
* for each n_ranks group.
*/
static const struct board_specific_parameters udimm0[] = {
/*
* memory controller 0
* num| hi| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
* ranks| mhz|adjst| start | ctl2 | ctl3 | |delay |
*/
{2, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0},
{2, 1666, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0},
{2, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0},
{1, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0},
{1, 1700, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0},
{1, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0},
{}
};
static const struct board_specific_parameters *udimms[] = {
udimm0,
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
if (ctrl_num > 2) {
printf("Not supported controller number %d\n", ctrl_num);
return;
}
if (!pdimm->n_ranks)
return;
pbsp = udimms[0];
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
while (pbsp->datarate_mhz_high) {
if (pbsp->n_ranks == pdimm->n_ranks) {
if (ddr_freq <= pbsp->datarate_mhz_high) {
popts->cpo_override = pbsp->cpo;
popts->write_data_delay =
pbsp->write_data_delay;
popts->clk_adjust = pbsp->clk_adjust;
popts->wrlvl_start = pbsp->wrlvl_start;
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
popts->twoT_en = pbsp->force_2T;
goto found;
}
pbsp_highest = pbsp;
}
pbsp++;
}
if (pbsp_highest) {
printf("Error: board specific timing not found "
"for data rate %lu MT/s\n"
"Trying to use the highest speed (%u) parameters\n",
ddr_freq, pbsp_highest->datarate_mhz_high);
popts->cpo_override = pbsp_highest->cpo;
popts->write_data_delay = pbsp_highest->write_data_delay;
popts->clk_adjust = pbsp_highest->clk_adjust;
popts->wrlvl_start = pbsp_highest->wrlvl_start;
popts->twoT_en = pbsp_highest->force_2T;
} else {
panic("DIMM is not supported by this board");
}
found:
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
/*
* Write leveling override
*/
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xf;
/*
* Rtt and Rtt_WR override
*/
popts->rtt_override = 0;
/* Enable ZQ calibration */
popts->zq_en = 1;
/* DHC_EN =1, ODT = 75 Ohm */
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
}
phys_size_t initdram(int board_type)
{
phys_size_t dram_size;
puts("Initializing....using SPD\n");
dram_size = fsl_ddr_sdram();
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
puts(" DDR: ");
return dram_size;
}

338
board/freescale/b4860qds/eth_b4860qds.c Normal file
View File

@@ -0,0 +1,338 @@
/*
* Copyright 2012 Freescale Semiconductor, Inc.
* Author: Sandeep Kumar Singh <sandeep@freescale.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/* This file is based on board/freescale/corenet_ds/eth_superhydra.c */
/*
* This file handles the board muxing between the Fman Ethernet MACs and
* the RGMII/SGMII/XGMII PHYs on a Freescale B4860 "Centaur". The SGMII
* PHYs are the two on-board 1Gb ports. There are no RGMII PHY on board.
* The 10Gb XGMII PHY is provided via the XAUI riser card. There is only
* one Fman device on B4860. The SERDES configuration is used to determine
* where the SGMII and XAUI cards exist, and also which Fman MACs are routed
* to which PHYs. So for a given Fman MAC, there is one and only PHY it
* connects to. MACs cannot be routed to PHYs dynamically. This configuration
* is done at boot time by reading SERDES protocol from RCW.
*/
#include <common.h>
#include <netdev.h>
#include <asm/fsl_serdes.h>
#include <fm_eth.h>
#include <fsl_mdio.h>
#include <malloc.h>
#include <fdt_support.h>
#include <asm/fsl_dtsec.h>
#include "../common/ngpixis.h"
#include "../common/fman.h"
#include "../common/qixis.h"
#include "b4860qds_qixis.h"
#define EMI_NONE 0xFFFFFFFF
#ifdef CONFIG_FMAN_ENET
/*
* Mapping of all 16 SERDES lanes to board slots. A value n(>0) will mean that
* lane at index is mapped to slot number n. A value of '0' will mean
* that the mapping must be determined dynamically, or that the lane maps to
* something other than a board slot
*/
static u8 lane_to_slot[] = {
0, 0, 0, 0,
0, 0, 0, 0,
1, 1, 1, 1,
0, 0, 0, 0
};
/*
* This function initializes the lane_to_slot[] array. It reads RCW to check
* if Serdes2{E,F,G,H} is configured as slot 2 or as SFP and initializes
* lane_to_slot[] accordingly
*/
static void initialize_lane_to_slot(void)
{
unsigned int serdes2_prtcl;
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
debug("Initializing lane to slot: Serdes2 protocol: %x\n",
serdes2_prtcl);
switch (serdes2_prtcl) {
case 0x18:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: SGMII
* Lanes: E,F: Aur
* Lanes: G,H: SRIO
*/
case 0x91:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B: SGMII
* Lanes: C,D: SRIO2
* Lanes: E,F,G,H: XAUI2
*/
case 0x93:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: SGMII
* Lanes: E,F,G,H: XAUI2
*/
case 0x98:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: XAUI2
* Lanes: E,F,G,H: XAUI2
*/
case 0x9a:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B: PCI
* Lanes: C,D: SGMII
* Lanes: E,F,G,H: XAUI2
*/
case 0x9e:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: PCI
* Lanes: E,F,G,H: XAUI2
*/
case 0xb2:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: PCI
* Lanes: E,F: SGMII 3&4
* Lanes: G,H: XFI
*/
case 0xc2:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B: SGMII
* Lanes: C,D: SRIO2
* Lanes: E,F,G,H: XAUI2
*/
lane_to_slot[12] = 2;
lane_to_slot[13] = lane_to_slot[12];
lane_to_slot[14] = lane_to_slot[12];
lane_to_slot[15] = lane_to_slot[12];
break;
default:
printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n",
serdes2_prtcl);
break;
}
return;
}
#endif /* #ifdef CONFIG_FMAN_ENET */
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
struct memac_mdio_info memac_mdio_info;
struct memac_mdio_info tg_memac_mdio_info;
unsigned int i;
unsigned int serdes1_prtcl, serdes2_prtcl;
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
if (!serdes1_prtcl) {
printf("SERDES1 is not enabled\n");
return 0;
}
serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl);
serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
if (!serdes2_prtcl) {
printf("SERDES2 is not enabled\n");
return 0;
}
serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl);
printf("Initializing Fman\n");
initialize_lane_to_slot();
memac_mdio_info.regs =
(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
memac_mdio_info.name = DEFAULT_FM_MDIO_NAME;
/* Register the real 1G MDIO bus */
fm_memac_mdio_init(bis, &memac_mdio_info);
tg_memac_mdio_info.regs =
(struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
tg_memac_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
/* Register the real 10G MDIO bus */
fm_memac_mdio_init(bis, &tg_memac_mdio_info);
/*
* Program the two on board DTSEC PHY addresses assuming that they are
* all SGMII. RGMII is not supported on this board. Setting SGMII 5 and
* 6 to on board SGMII phys
*/
fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
switch (serdes1_prtcl) {
case 0x2a:
/* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */
debug("Setting phy addresses for FM1_DTSEC5: %x and"
"FM1_DTSEC6: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
/* Fixing Serdes clock by programming FPGA register */
QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
fm_info_set_phy_address(FM1_DTSEC5,
CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
break;
#ifdef CONFIG_PPC_B4420
case 0x18:
/* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */
debug("Setting phy addresses for FM1_DTSEC3: %x and"
"FM1_DTSEC4: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
/* Fixing Serdes clock by programming FPGA register */
QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
break;
#endif
default:
printf("Fman: Unsupported SerDes1 Protocol 0x%02x\n",
serdes1_prtcl);
break;
}
switch (serdes2_prtcl) {
case 0x18:
debug("Setting phy addresses on SGMII Riser card for"
"FM1_DTSEC ports: \n");
fm_info_set_phy_address(FM1_DTSEC1,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2,
CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR);
break;
case 0x49:
debug("Setting phy addresses on SGMII Riser card for"
"FM1_DTSEC ports: \n");
fm_info_set_phy_address(FM1_DTSEC1,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2,
CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR);
break;
case 0x8d:
case 0xb2:
debug("Setting phy addresses on SGMII Riser card for"
"FM1_DTSEC ports: \n");
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
break;
default:
printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n",
serdes2_prtcl);
break;
}
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
int idx = i - FM1_DTSEC1;
switch (fm_info_get_enet_if(i)) {
case PHY_INTERFACE_MODE_SGMII:
fm_info_set_mdio(i,
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
break;
case PHY_INTERFACE_MODE_NONE:
fm_info_set_phy_address(i, 0);
break;
default:
printf("Fman1: DTSEC%u set to unknown interface %i\n",
idx + 1, fm_info_get_enet_if(i));
fm_info_set_phy_address(i, 0);
break;
}
}
cpu_eth_init(bis);
#endif
return pci_eth_init(bis);
}
void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
enum fm_port port, int offset)
{
int phy;
char alias[32];
if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
phy = fm_info_get_phy_address(port);
sprintf(alias, "phy_sgmii_%x", phy);
fdt_set_phy_handle(fdt, compat, addr, alias);
}
}
void fdt_fixup_board_enet(void *fdt)
{
int i;
char alias[32];
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
switch (fm_info_get_enet_if(i)) {
case PHY_INTERFACE_MODE_NONE:
sprintf(alias, "ethernet%u", i);
fdt_status_disabled_by_alias(fdt, alias);
break;
default:
break;
}
}
}

44
board/freescale/b4860qds/law.c Normal file
View File

@@ -0,0 +1,44 @@
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/fsl_law.h>
#include <asm/mmu.h>
struct law_entry law_table[] = {
SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
#endif
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
#endif
SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
#ifdef CONFIG_SYS_DCSRBAR_PHYS
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
#endif
#ifdef CONFIG_SYS_NAND_BASE_PHYS
SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
#endif
};
int num_law_entries = ARRAY_SIZE(law_table);

39
board/freescale/b4860qds/pci.c Normal file
View File

@@ -0,0 +1,39 @@
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <command.h>
#include <pci.h>
#include <asm/fsl_pci.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <asm/fsl_serdes.h>
void pci_init_board(void)
{
fsl_pcie_init_board(0);
}
void pci_of_setup(void *blob, bd_t *bd)
{
FT_FSL_PCI_SETUP;
}

127
board/freescale/b4860qds/tlb.c Normal file
View File

@@ -0,0 +1,127 @@
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/mmu.h>
struct fsl_e_tlb_entry tlb_table[] = {
/* TLB 0 - for temp stack in cache */
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
CONFIG_SYS_INIT_RAM_ADDR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
/* TLB 1 */
/* *I*** - Covers boot page */
#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
/*
* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
* SRAM is at 0xfff00000, it covered the 0xfffff000.
*/
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 0, BOOKE_PAGESZ_1M, 1),
#else
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 0, BOOKE_PAGESZ_4K, 1),
#endif
/* *I*G* - CCSRBAR */
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 1, BOOKE_PAGESZ_16M, 1),
/* *I*G* - Flash, localbus */
/* This will be changed to *I*G* after relocation to RAM. */
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 3, BOOKE_PAGESZ_256M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000,
CONFIG_SYS_PCIE1_MEM_PHYS + 0x10000000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 4, BOOKE_PAGESZ_256M, 1),
/* *I*G* - PCI I/O */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 5, BOOKE_PAGESZ_64K, 1),
/* Bman/Qman */
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 6, BOOKE_PAGESZ_16M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 7, BOOKE_PAGESZ_16M, 1),
#endif
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 8, BOOKE_PAGESZ_16M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 9, BOOKE_PAGESZ_16M, 1),
#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 10, BOOKE_PAGESZ_4M, 1),
#endif
#ifdef CONFIG_SYS_NAND_BASE
/*
* *I*G - NAND
* entry 14 and 15 has been used hard coded, they will be disabled
* in cpu_init_f, so we use entry 16 for nand.
*/
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 11, BOOKE_PAGESZ_64K, 1),
#endif
SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 12, BOOKE_PAGESZ_4K, 1),
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);