From a1a61b0672ff20719ac9d1f4d60c16da00d11538 Mon Sep 17 00:00:00 2001 From: Ezra Buehler Date: Sat, 9 May 2020 22:05:38 +0200 Subject: [PATCH 1/4] arm: mvebu: ds414: add u-boot,dm-pre-reloc to spi0 Without this U-Boot-specific property, booting on the Synology DS414 (or DS214+) fails in SPL. The spi0 DT node is not scanned, as a result the SPI flash cannot be found. Signed-off-by: Ezra Buehler Reviewed-by: Stefan Roese --- arch/arm/dts/armada-xp-synology-ds414-u-boot.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) create mode 100644 arch/arm/dts/armada-xp-synology-ds414-u-boot.dtsi diff --git a/arch/arm/dts/armada-xp-synology-ds414-u-boot.dtsi b/arch/arm/dts/armada-xp-synology-ds414-u-boot.dtsi new file mode 100644 index 0000000000..22fae16c9d --- /dev/null +++ b/arch/arm/dts/armada-xp-synology-ds414-u-boot.dtsi @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ + +&spi0 { + u-boot,dm-pre-reloc; + + spi-flash@0 { + u-boot,dm-pre-reloc; + }; +}; From 0700093b852ac62bc68a80e96dea9ba255d7efbc Mon Sep 17 00:00:00 2001 From: Ezra Buehler Date: Sat, 9 May 2020 22:05:39 +0200 Subject: [PATCH 2/4] arm: mvebu: ds414: define CONFIG_SYS_U_BOOT_OFFS Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot will be located at address 0x16000. But, SPL will try to load the payload from 0x24000 causing the boot to hang. Signed-off-by: Ezra Buehler Reviewed-by: Stefan Roese --- include/configs/ds414.h | 3 +++ 1 file changed, 3 insertions(+) diff --git a/include/configs/ds414.h b/include/configs/ds414.h index e3693767b6..b179b99468 100644 --- a/include/configs/ds414.h +++ b/include/configs/ds414.h @@ -87,7 +87,10 @@ #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) +#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI) /* SPL related SPI defines */ +#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS +#endif /* DS414 bus width is 32bits */ #define CONFIG_DDR_32BIT From 8678776df6f5b77bbb504b2b3b02e61f73b9168d Mon Sep 17 00:00:00 2001 From: Jakov Petrina Date: Tue, 12 May 2020 12:02:47 +0200 Subject: [PATCH 3/4] arm: mvebu: armada-3720-uDPU: fix PHY mode definition to sgmii-2500 Commit f49ac7e1c4 switched the default PHY speed to 3.125Gbit to resolve issues with SFP modules. However, U-Boot does not have a "2500base-x" phy-mode. Resolve this by using "sgmii-2500" instead. Signed-off-by: Jakov Petrina Signed-off-by: Vladimir Vid Reviewed-by: Stefan Roese Cc: Luka Perkov Cc: Stefan Roese --- arch/arm/dts/armada-3720-uDPU.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/dts/armada-3720-uDPU.dts b/arch/arm/dts/armada-3720-uDPU.dts index 07c7b91175..7f4b8222f4 100644 --- a/arch/arm/dts/armada-3720-uDPU.dts +++ b/arch/arm/dts/armada-3720-uDPU.dts @@ -125,14 +125,14 @@ ð0 { pinctrl-0 = <&pcie_pins>; status = "okay"; - phy-mode = "2500base-x"; + phy-mode = "sgmii-2500"; managed = "in-band-status"; phy = <ðphy0>; }; ð1 { status = "okay"; - phy-mode = "2500base-x"; + phy-mode = "sgmii-2500"; managed = "in-band-status"; phy = <ðphy1>; }; From df9ebbe17ea13de4c443849ecf23cba545dd0395 Mon Sep 17 00:00:00 2001 From: Luka Kovacic Date: Tue, 26 May 2020 20:17:50 +0200 Subject: [PATCH 4/4] arm: mvebu: Convert CRS305-1G-4S board to CRS3xx-98DX3236 Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier implementation of new CRS3xx series boards, based on Marvell Prestera 98DX3236. Signed-off-by: Luka Kovacic Reviewed-by: Stefan Roese Cc: Luka Perkov Cc: Jakov Petrina --- arch/arm/dts/armada-xp-crs305-1g-4s.dts | 103 +--------------- arch/arm/dts/armada-xp-crs305-1g-4s.dtsi | 111 ++++++++++++++++++ arch/arm/mach-mvebu/Kconfig | 10 +- board/mikrotik/crs305-1g-4s/MAINTAINERS | 7 -- .../.gitignore | 0 board/mikrotik/crs3xx-98dx3236/MAINTAINERS | 11 ++ .../Makefile | 2 +- .../{crs305-1g-4s => crs3xx-98dx3236}/README | 12 +- .../binary.0 | 0 .../crs3xx-98dx3236.c} | 0 .../kwbimage.cfg.in | 2 +- configs/crs305-1g-4s_defconfig | 46 ++++---- .../{crs305-1g-4s.h => crs3xx-98dx3236.h} | 6 +- 13 files changed, 165 insertions(+), 145 deletions(-) create mode 100644 arch/arm/dts/armada-xp-crs305-1g-4s.dtsi delete mode 100644 board/mikrotik/crs305-1g-4s/MAINTAINERS rename board/mikrotik/{crs305-1g-4s => crs3xx-98dx3236}/.gitignore (100%) create mode 100644 board/mikrotik/crs3xx-98dx3236/MAINTAINERS rename board/mikrotik/{crs305-1g-4s => crs3xx-98dx3236}/Makefile (93%) rename board/mikrotik/{crs305-1g-4s => crs3xx-98dx3236}/README (64%) rename board/mikrotik/{crs305-1g-4s => crs3xx-98dx3236}/binary.0 (100%) rename board/mikrotik/{crs305-1g-4s/crs305-1g-4s.c => crs3xx-98dx3236/crs3xx-98dx3236.c} (100%) rename board/mikrotik/{crs305-1g-4s => crs3xx-98dx3236}/kwbimage.cfg.in (75%) rename include/configs/{crs305-1g-4s.h => crs3xx-98dx3236.h} (87%) diff --git a/arch/arm/dts/armada-xp-crs305-1g-4s.dts b/arch/arm/dts/armada-xp-crs305-1g-4s.dts index 1116f5c96c..010b83b542 100644 --- a/arch/arm/dts/armada-xp-crs305-1g-4s.dts +++ b/arch/arm/dts/armada-xp-crs305-1g-4s.dts @@ -1,110 +1,17 @@ // SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* - * Device Tree file for CRS305-1G-4S board + * Device Tree file for MikroTik CRS305-1G-4S+ board * - * Copyright (C) 2016 Allied Telesis Labs - * - * Based on armada-xp-db.dts - * - * Note: this Device Tree assumes that the bootloader has remapped the - * internal registers to 0xf1000000 (instead of the default - * 0xd0000000). The 0xf1000000 is the default used by the recent, - * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier - * boards were delivered with an older version of the bootloader that - * left internal registers mapped at 0xd0000000. If you are in this - * situation, you should either update your bootloader (preferred - * solution) or the below Device Tree should be adjusted. + * Copyright (C) 2020 Sartura Ltd. + * Author: Luka Kovacic */ -/dts-v1/; -#include "armada-xp-98dx3236.dtsi" -#include "armada-xp-crs305-1g-4s-u-boot.dtsi" +#include "armada-xp-crs305-1g-4s.dtsi" / { - model = "CRS305-1G-4S"; - compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp"; - - chosen { - stdout-path = "serial0:115200n8"; - bootargs = "console=ttyS0,115200 earlyprintk"; - }; - - aliases { - spi0 = &spi0; - }; - - memory { - device_type = "memory"; - reg = <0 0x00000000 0 0x20000000>; /* 512 MB */ - }; -}; - -&L2 { - arm,parity-enable; - marvell,ecc-enable; -}; - -&devbus_bootcs { - status = "okay"; - - /* Device Bus parameters are required */ - - /* Read parameters */ - devbus,bus-width = <16>; - devbus,turn-off-ps = <60000>; - devbus,badr-skew-ps = <0>; - devbus,acc-first-ps = <124000>; - devbus,acc-next-ps = <248000>; - devbus,rd-setup-ps = <0>; - devbus,rd-hold-ps = <0>; - - /* Write parameters */ - devbus,sync-enable = <0>; - devbus,wr-high-ps = <60000>; - devbus,wr-low-ps = <60000>; - devbus,ale-wr-ps = <60000>; -}; - -&uart0 { - status = "okay"; -}; - -&uart1 { - status = "okay"; -}; - -&i2c0 { - clock-frequency = <100000>; - status = "okay"; -}; - -&usb0 { - status = "okay"; + model = "MikroTik CRS305-1G-4S+"; }; &spi0 { status = "okay"; - - spi-flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "spi-flash", "jedec,spi-nor"; - reg = <0>; /* Chip select 0 */ - spi-max-frequency = <108000000>; - m25p,fast-read; - - partition@u-boot { - reg = <0x00000000 0x00100000>; - label = "u-boot"; - }; - partition@u-boot-env { - reg = <0x00100000 0x00040000>; - label = "u-boot-env"; - }; - partition@unused { - reg = <0x00140000 0x00ec0000>; - label = "unused"; - }; - - }; }; diff --git a/arch/arm/dts/armada-xp-crs305-1g-4s.dtsi b/arch/arm/dts/armada-xp-crs305-1g-4s.dtsi new file mode 100644 index 0000000000..c8839eac94 --- /dev/null +++ b/arch/arm/dts/armada-xp-crs305-1g-4s.dtsi @@ -0,0 +1,111 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree file for CRS305-1G-4S board + * + * Copyright (C) 2016 Allied Telesis Labs + * Copyright (C) 2020 Sartura Ltd. + * + * Based on armada-xp-db.dts + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the default + * 0xd0000000). The 0xf1000000 is the default used by the recent, + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier + * boards were delivered with an older version of the bootloader that + * left internal registers mapped at 0xd0000000. If you are in this + * situation, you should either update your bootloader (preferred + * solution) or the below Device Tree should be adjusted. + */ + +/dts-v1/; +#include "armada-xp-98dx3236.dtsi" +#include "armada-xp-crs305-1g-4s-u-boot.dtsi" + +/ { + model = "CRS305-1G-4S+"; + compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + aliases { + spi0 = &spi0; + }; + + memory { + device_type = "memory"; + reg = <0 0x00000000 0 0x20000000>; /* 512 MB */ + }; +}; + +&L2 { + arm,parity-enable; + marvell,ecc-enable; +}; + +&devbus_bootcs { + status = "okay"; + + /* Device Bus parameters are required */ + + /* Read parameters */ + devbus,bus-width = <16>; + devbus,turn-off-ps = <60000>; + devbus,badr-skew-ps = <0>; + devbus,acc-first-ps = <124000>; + devbus,acc-next-ps = <248000>; + devbus,rd-setup-ps = <0>; + devbus,rd-hold-ps = <0>; + + /* Write parameters */ + devbus,sync-enable = <0>; + devbus,wr-high-ps = <60000>; + devbus,wr-low-ps = <60000>; + devbus,ale-wr-ps = <60000>; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <100000>; + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <108000000>; + m25p,fast-read; + + partition@u-boot { + reg = <0x00000000 0x00080000>; + label = "u-boot"; + }; + partition@u-boot-env { + reg = <0x00080000 0x00010000>; + label = "u-boot-env"; + }; + partition@firmware { + reg = <0x00090000 0x00f70000>; + label = "firmware"; + }; + + }; +}; diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 645990b3ef..0d8e0922a2 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -165,8 +165,8 @@ config TARGET_DB_XC3_24G4XG bool "Support DB-XC3-24G4XG" select 98DX3336 -config TARGET_CRS305_1G_4S - bool "Support CRS305-1G-4S" +config TARGET_CRS3XX_98DX3236 + bool "Support CRS3XX-98DX3236" select 98DX3236 endchoice @@ -188,7 +188,7 @@ config SYS_BOARD default "a38x" if TARGET_CONTROLCENTERDC default "x530" if TARGET_X530 default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG - default "crs305-1g-4s" if TARGET_CRS305_1G_4S + default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236 config SYS_CONFIG_NAME default "clearfog" if TARGET_CLEARFOG @@ -207,7 +207,7 @@ config SYS_CONFIG_NAME default "controlcenterdc" if TARGET_CONTROLCENTERDC default "x530" if TARGET_X530 default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG - default "crs305-1g-4s" if TARGET_CRS305_1G_4S + default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236 config SYS_VENDOR default "Marvell" if TARGET_DB_MV784MP_GP @@ -225,7 +225,7 @@ config SYS_VENDOR default "CZ.NIC" if TARGET_TURRIS_MOX default "gdsys" if TARGET_CONTROLCENTERDC default "alliedtelesis" if TARGET_X530 - default "mikrotik" if TARGET_CRS305_1G_4S + default "mikrotik" if TARGET_CRS3XX_98DX3236 config SYS_SOC default "mvebu" diff --git a/board/mikrotik/crs305-1g-4s/MAINTAINERS b/board/mikrotik/crs305-1g-4s/MAINTAINERS deleted file mode 100644 index 3823489600..0000000000 --- a/board/mikrotik/crs305-1g-4s/MAINTAINERS +++ /dev/null @@ -1,7 +0,0 @@ -CRS305-1G-4S BOARD -M: Luka Kovacic -S: Maintained -F: board/mikrotik/crs305-1g-4s/ -F: include/configs/crs305-1g-4s.h -F: configs/crs305-1g-4s_defconfig -F: arch/arm/dts/armada-xp-crs305-1g-4s.dts diff --git a/board/mikrotik/crs305-1g-4s/.gitignore b/board/mikrotik/crs3xx-98dx3236/.gitignore similarity index 100% rename from board/mikrotik/crs305-1g-4s/.gitignore rename to board/mikrotik/crs3xx-98dx3236/.gitignore diff --git a/board/mikrotik/crs3xx-98dx3236/MAINTAINERS b/board/mikrotik/crs3xx-98dx3236/MAINTAINERS new file mode 100644 index 0000000000..127e0eac60 --- /dev/null +++ b/board/mikrotik/crs3xx-98dx3236/MAINTAINERS @@ -0,0 +1,11 @@ +CRS3XX-98DX3236 BOARD +M: Luka Kovacic +S: Maintained +F: board/mikrotik/crs3xx-98dx3236/ +F: include/configs/crs3xx-98dx3236.h + +CRS305-1G-4S BOARD +M: Luka Kovacic +S: Maintained +F: configs/crs305-1g-4s_defconfig +F: arch/arm/dts/armada-xp-crs305-1g-4s.dts diff --git a/board/mikrotik/crs305-1g-4s/Makefile b/board/mikrotik/crs3xx-98dx3236/Makefile similarity index 93% rename from board/mikrotik/crs305-1g-4s/Makefile rename to board/mikrotik/crs3xx-98dx3236/Makefile index c03f534e48..0b2930d3e2 100644 --- a/board/mikrotik/crs305-1g-4s/Makefile +++ b/board/mikrotik/crs3xx-98dx3236/Makefile @@ -2,7 +2,7 @@ # # Copyright (C) 2015 Stefan Roese -obj-y := crs305-1g-4s.o +obj-y := crs3xx-98dx3236.o extra-y := kwbimage.cfg quiet_cmd_sed = SED $@ diff --git a/board/mikrotik/crs305-1g-4s/README b/board/mikrotik/crs3xx-98dx3236/README similarity index 64% rename from board/mikrotik/crs305-1g-4s/README rename to board/mikrotik/crs3xx-98dx3236/README index f420aabfbf..952f774ab7 100644 --- a/board/mikrotik/crs305-1g-4s/README +++ b/board/mikrotik/crs3xx-98dx3236/README @@ -1,13 +1,13 @@ -MikroTik CRS305-1G-4S+IN +MikroTik CRS3XX-98DX3236 ======================== -CRS305-1G-4S+IN is a 4x SFP+ switch with a Gigabit Ethernet port for management. -Specifications: +CRS3XX-98DX3236 is a U-Boot port that supports a series of MikroTik switches +based on the Marvell Prestera 98DX3236 switch with an integrated CPU. + +Common specifications: - Marvell Prestera 98DX3236 switch with an integrated ARMv7 CPU - 512 MB DDR3 RAM - UART @ 115200bps - - 4x SFP+ - - Gigabit Ethernet (AR8033) - 16 MB SPI flash (Winbond 25Q128JVSM) Currently supported hardware: @@ -15,7 +15,7 @@ Currently supported hardware: - SPI boot, environment and load kernel Planned: - - Gigabit Ethernet support + - Gigabit Ethernet support (internal CPU <-> switch fabric connection) Getting binary.0 ================ diff --git a/board/mikrotik/crs305-1g-4s/binary.0 b/board/mikrotik/crs3xx-98dx3236/binary.0 similarity index 100% rename from board/mikrotik/crs305-1g-4s/binary.0 rename to board/mikrotik/crs3xx-98dx3236/binary.0 diff --git a/board/mikrotik/crs305-1g-4s/crs305-1g-4s.c b/board/mikrotik/crs3xx-98dx3236/crs3xx-98dx3236.c similarity index 100% rename from board/mikrotik/crs305-1g-4s/crs305-1g-4s.c rename to board/mikrotik/crs3xx-98dx3236/crs3xx-98dx3236.c diff --git a/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in b/board/mikrotik/crs3xx-98dx3236/kwbimage.cfg.in similarity index 75% rename from board/mikrotik/crs305-1g-4s/kwbimage.cfg.in rename to board/mikrotik/crs3xx-98dx3236/kwbimage.cfg.in index 2dbbbd0246..9a58b33a6f 100644 --- a/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in +++ b/board/mikrotik/crs3xx-98dx3236/kwbimage.cfg.in @@ -9,4 +9,4 @@ VERSION 1 BOOT_FROM spi # Binary Header (bin_hdr) with DDR3 training code -BINARY board/mikrotik/crs305-1g-4s/binary.0 0000005b 00000068 +BINARY board/mikrotik/crs3xx-98dx3236/binary.0 0000005b 00000068 diff --git a/configs/crs305-1g-4s_defconfig b/configs/crs305-1g-4s_defconfig index 7632fc4254..27043bf69a 100644 --- a/configs/crs305-1g-4s_defconfig +++ b/configs/crs305-1g-4s_defconfig @@ -3,48 +3,46 @@ CONFIG_ARCH_CPU_INIT=y CONFIG_ARCH_MVEBU=y CONFIG_SYS_TEXT_BASE=0x00800000 CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_TARGET_CRS305_1G_4S=y +CONFIG_TARGET_CRS3XX_98DX3236=y CONFIG_ENV_SIZE=0x10000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_ENV_SECT_SIZE=0x40000 +CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_ENV_OFFSET=0x80000 +# CONFIG_EFI_LOADER is not set CONFIG_BUILD_TARGET="u-boot.kwb" CONFIG_USE_PREBOOT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_PROMPT="Autoboot in %d seconds, to stop use 's' key\n" +CONFIG_AUTOBOOT_STOP_STR="s" +CONFIG_AUTOBOOT_KEYED_CTRLC=y CONFIG_CMD_BOOTZ=y -CONFIG_CMD_MEMTEST=y -CONFIG_SYS_ALT_MEMTEST=y -CONFIG_SYS_MEMTEST_START=0x00800000 -CONFIG_SYS_MEMTEST_END=0x00ffffff # CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y +# CONFIG_CMD_I2C is not set CONFIG_CMD_SPI=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_TFTPPUT=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y -CONFIG_CMD_TIME=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_EXT4=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y -CONFIG_CMD_UBI=y +# CONFIG_CMD_UBI is not set +CONFIG_CMD_MTD=y +CONFIG_CMD_MTDPARTS=y CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs305-1g-4s" CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_BLK=y -CONFIG_DM_I2C=y -CONFIG_SYS_I2C_MVTWSI=y +# CONFIG_DM_I2C is not set +# CONFIG_SYS_I2C_MVTWSI is not set # CONFIG_MMC is not set CONFIG_MTD=y +CONFIG_MTD_PARTITIONS=y CONFIG_DM_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_MTD=y CONFIG_SPI_FLASH_SFDP_SUPPORT=y -CONFIG_SPI_FLASH_MACRONIX=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_WINBOND=y # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_FIT=y +CONFIG_FIT_ENABLE_SHA256_SUPPORT=y +CONFIG_FIT_VERBOSE=y +CONFIG_FIT_BEST_MATCH=y CONFIG_PCI=y CONFIG_PCI_MVEBU=y CONFIG_SYS_NS16550=y diff --git a/include/configs/crs305-1g-4s.h b/include/configs/crs3xx-98dx3236.h similarity index 87% rename from include/configs/crs305-1g-4s.h rename to include/configs/crs3xx-98dx3236.h index 617c8af83a..e2ba7b8126 100644 --- a/include/configs/crs305-1g-4s.h +++ b/include/configs/crs3xx-98dx3236.h @@ -3,8 +3,8 @@ * Copyright (C) 2014 Stefan Roese */ -#ifndef _CONFIG_CRS305_1G_4S_H -#define _CONFIG_CRS305_1G_4S_H +#ifndef _CONFIG_CRS3XX_98DX3236_H +#define _CONFIG_CRS3XX_98DX3236_H /* * High Level Configuration Options (easy to change) @@ -32,4 +32,4 @@ #undef CONFIG_SYS_MAXARGS #define CONFIG_SYS_MAXARGS 96 -#endif /* _CONFIG_CRS305_1G_4S_H */ +#endif /* _CONFIG_CRS3XX_98DX3236_H */