Merge git://git.denx.de/u-boot-marvell

- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)

drivers/ddr/marvell/a38x/ddr3_training_db.c

@@ -420,13 +420,13 @@ unsigned int mv_ddr_speed_bin_timing_get(enum mv_ddr_speed_bin index, enum mv_dd
 		result = speed_bin_table_t_rcd_t_rp[index];
 		break;
 	case SPEED_BIN_TRAS:
-		if (index < SPEED_BIN_DDR_1066G)
+		if (index <= SPEED_BIN_DDR_1066G)
 			result = 37500;
-		else if (index < SPEED_BIN_DDR_1333J)
+		else if (index <= SPEED_BIN_DDR_1333J)
 			result = 36000;
-		else if (index < SPEED_BIN_DDR_1600K)
+		else if (index <= SPEED_BIN_DDR_1600K)
 			result = 35000;
-		else if (index < SPEED_BIN_DDR_1866M)
+		else if (index <= SPEED_BIN_DDR_1866M)
 			result = 34000;
 		else
 			result = 33000;

drivers/ddr/marvell/a38x/ddr3_training_hw_algo.c

@@ -50,6 +50,7 @@ int ddr3_tip_write_additional_odt_setting(u32 dev_num, u32 if_id)
 	int max_phase = MIN_VALUE, current_phase;
 	enum hws_access_type access_type = ACCESS_TYPE_UNICAST;
 	u32 octets_per_if_num = ddr3_tip_dev_attr_get(dev_num, MV_ATTR_OCTET_PER_INTERFACE);
+	unsigned int max_cs = mv_ddr_cs_num_get();
 
 	CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
 				       DUNIT_ODT_CTRL_REG,
@@ -59,7 +60,7 @@ int ddr3_tip_write_additional_odt_setting(u32 dev_num, u32 if_id)
 				      data_read, MASK_ALL_BITS));
 	val = data_read[if_id];
 
-	for (cs_num = 0; cs_num < MAX_CS_NUM; cs_num++) {
+	for (cs_num = 0; cs_num < max_cs; cs_num++) {
 		read_sample[cs_num] = GET_RD_SAMPLE_DELAY(val, cs_num);
 
 		/* find maximum of read_samples */

drivers/pci/pci_mvebu.c

@@ -369,6 +369,12 @@ static int mvebu_get_tgt_attr(ofnode node, int devfn,
 	if (!range)
 		return -EINVAL;
 
+	/*
+	 * Linux uses of_n_addr_cells() to get the number of address cells
+	 * here. Currently this function is only available in U-Boot when
+	 * CONFIG_OF_LIVE is enabled. Until this is enabled for MVEBU in
+	 * general, lets't hardcode the "pna" value in the U-Boot code.
+	 */
 	pna = 2; /* hardcoded for now because of lack of of_n_addr_cells() */
 	rangesz = pna + na + ns;
 	nranges = rlen / sizeof(__be32) / rangesz;