leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

board: mx6sabreauto: Remove the non-DM code

Browse Source 
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabreauto board file.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This commit is contained in:
Abel Vesa 2019-02-01 16:40:22 +00:00 committed by Stefano Babic
parent ef4749f085
commit 9e41cbf133
1 changed files with 0 additions and 70 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

70
board/freescale/mx6sabreauto/mx6sabreauto.c
View File

@ -159,44 +159,6 @@ static iomux_v3_cfg_t const port_exp[] = {
IOMUX_PADS(PAD_SD2_DAT0__GPIO1_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
/*Define for building port exp gpio, pin starts from 0*/
#define PORTEXP_IO_NR(chip, pin) \
((chip << 5) + pin)
/*Get the chip addr from a ioexp gpio*/
#define PORTEXP_IO_TO_CHIP(gpio_nr) \
(gpio_nr >> 5)
/*Get the pin number from a ioexp gpio*/
#define PORTEXP_IO_TO_PIN(gpio_nr) \
(gpio_nr & 0x1f)
static int port_exp_direction_output(unsigned gpio, int value)
{
int ret;
i2c_set_bus_num(2);
ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
if (ret)
return ret;
ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
(1 << PORTEXP_IO_TO_PIN(gpio)),
(PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
if (ret)
return ret;
ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
(1 << PORTEXP_IO_TO_PIN(gpio)),
(value << PORTEXP_IO_TO_PIN(gpio)));
if (ret)
return ret;
return 0;
}
#ifdef CONFIG_MTD_NOR_FLASH
static iomux_v3_cfg_t const eimnor_pads[] = {
IOMUX_PADS(PAD_EIM_D16__EIM_DATA16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
@ -681,19 +643,10 @@ int checkboard(void)
}
#ifdef CONFIG_USB_EHCI_MX6
#define USB_HOST1_PWR PORTEXP_IO_NR(0x32, 7)
#define USB_OTG_PWR PORTEXP_IO_NR(0x34, 1)
iomux_v3_cfg_t const usb_otg_pads[] = {
IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
int board_ehci_hcd_init(int port)
{
switch (port) {
case 0:
SETUP_IOMUX_PADS(usb_otg_pads);
/*
* Set daisy chain for otg_pin_id on 6q.
* For 6dl, this bit is reserved.
@ -708,29 +661,6 @@ int board_ehci_hcd_init(int port)
}
return 0;
}
int board_ehci_power(int port, int on)
{
switch (port) {
case 0:
if (on)
port_exp_direction_output(USB_OTG_PWR, 1);
else
port_exp_direction_output(USB_OTG_PWR, 0);
break;
case 1:
if (on)
port_exp_direction_output(USB_HOST1_PWR, 1);
else
port_exp_direction_output(USB_HOST1_PWR, 0);
break;
default:
printf("MXC USB port %d not yet supported\n", port);
return -EINVAL;
}
return 0;
}
#endif
#ifdef CONFIG_SPL_BUILD