ata_piix: Fix checkpatch issues
While in here also: - Switch to debug from custom PRINTF for debugging. - Use mdelay rather than custom msleep. Signed-off-by: Tom Rini <trini@ti.com>
This commit is contained in:
Tom Rini
parent
e5f24753c9
commit
879a57ac0e
@ -38,13 +38,13 @@
|
||||
extern block_dev_desc_t sata_dev_desc[CONFIG_SYS_SATA_MAX_DEVICE];
|
||||
extern int sata_curr_device;
|
||||
|
||||
#define DEBUG_SATA 0 /*For debug prints set DEBUG_SATA to 1 */
|
||||
#define DEBUG_SATA 0 /* For debug prints set DEBUG_SATA to 1 */
|
||||
|
||||
#define SATA_DECL
|
||||
#define DRV_DECL /*For file specific declarations */
|
||||
#define DRV_DECL /* For file specific declarations */
|
||||
#include "ata_piix.h"
|
||||
|
||||
/*Macros realted to PCI*/
|
||||
/* Macros realted to PCI */
|
||||
#define PCI_SATA_BUS 0x00
|
||||
#define PCI_SATA_DEV 0x1f
|
||||
#define PCI_SATA_FUNC 0x02
|
||||
@ -63,35 +63,36 @@ extern int sata_curr_device;
|
||||
#define PORT_ENABLED (1<<4)
|
||||
|
||||
u32 bdf;
|
||||
u32 iobase1 = 0; /*Primary cmd block */
|
||||
u32 iobase2 = 0; /*Primary ctl block */
|
||||
u32 iobase3 = 0; /*Sec cmd block */
|
||||
u32 iobase4 = 0; /*sec ctl block */
|
||||
u32 iobase5 = 0; /*BMDMA*/
|
||||
int
|
||||
pci_sata_init (void)
|
||||
u32 iobase1; /* Primary cmd block */
|
||||
u32 iobase2; /* Primary ctl block */
|
||||
u32 iobase3; /* Sec cmd block */
|
||||
u32 iobase4; /* sec ctl block */
|
||||
u32 iobase5; /* BMDMA*/
|
||||
|
||||
int pci_sata_init(void)
|
||||
{
|
||||
u32 bus = PCI_SATA_BUS;
|
||||
u32 dev = PCI_SATA_DEV;
|
||||
u32 fun = PCI_SATA_FUNC;
|
||||
u16 cmd = 0;
|
||||
u8 lat = 0, pcibios_max_latency = 0xff;
|
||||
u8 pmr; /*Port mapping reg */
|
||||
u8 pi; /*Prgming Interface reg */
|
||||
u8 pmr; /* Port mapping reg */
|
||||
u8 pi; /* Prgming Interface reg */
|
||||
|
||||
bdf = PCI_BDF (bus, dev, fun);
|
||||
pci_read_config_dword (bdf, PCI_SATA_BASE1, &iobase1);
|
||||
pci_read_config_dword (bdf, PCI_SATA_BASE2, &iobase2);
|
||||
pci_read_config_dword (bdf, PCI_SATA_BASE3, &iobase3);
|
||||
pci_read_config_dword (bdf, PCI_SATA_BASE4, &iobase4);
|
||||
pci_read_config_dword (bdf, PCI_SATA_BASE5, &iobase5);
|
||||
bdf = PCI_BDF(bus, dev, fun);
|
||||
pci_read_config_dword(bdf, PCI_SATA_BASE1, &iobase1);
|
||||
pci_read_config_dword(bdf, PCI_SATA_BASE2, &iobase2);
|
||||
pci_read_config_dword(bdf, PCI_SATA_BASE3, &iobase3);
|
||||
pci_read_config_dword(bdf, PCI_SATA_BASE4, &iobase4);
|
||||
pci_read_config_dword(bdf, PCI_SATA_BASE5, &iobase5);
|
||||
|
||||
if ((iobase1 == 0xFFFFFFFF) || (iobase2 == 0xFFFFFFFF) ||
|
||||
(iobase3 == 0xFFFFFFFF) || (iobase4 == 0xFFFFFFFF) ||
|
||||
(iobase5 == 0xFFFFFFFF)) {
|
||||
printf ("error no base addr for SATA controller\n");
|
||||
/* ERROR */
|
||||
printf("error no base addr for SATA controller\n");
|
||||
return 1;
|
||||
/*ERROR*/}
|
||||
}
|
||||
|
||||
iobase1 &= 0xFFFFFFFE;
|
||||
iobase2 &= 0xFFFFFFFE;
|
||||
@ -99,44 +100,42 @@ pci_sata_init (void)
|
||||
iobase4 &= 0xFFFFFFFE;
|
||||
iobase5 &= 0xFFFFFFFE;
|
||||
|
||||
/*check for mode */
|
||||
pci_read_config_byte (bdf, PCI_PMR, &pmr);
|
||||
/* check for mode */
|
||||
pci_read_config_byte(bdf, PCI_PMR, &pmr);
|
||||
if (pmr > 1) {
|
||||
printf ("combined mode not supported\n");
|
||||
puts("combined mode not supported\n");
|
||||
return 1;
|
||||
}
|
||||
|
||||
pci_read_config_byte (bdf, PCI_PI, &pi);
|
||||
pci_read_config_byte(bdf, PCI_PI, &pi);
|
||||
if ((pi & 0x05) != 0x05) {
|
||||
printf ("Sata is in Legacy mode\n");
|
||||
puts("Sata is in Legacy mode\n");
|
||||
return 1;
|
||||
} else {
|
||||
printf ("sata is in Native mode\n");
|
||||
}
|
||||
} else
|
||||
puts("sata is in Native mode\n");
|
||||
|
||||
/*MASTER CFG AND IO CFG */
|
||||
pci_read_config_word (bdf, PCI_COMMAND, &cmd);
|
||||
/* MASTER CFG AND IO CFG */
|
||||
pci_read_config_word(bdf, PCI_COMMAND, &cmd);
|
||||
cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_IO;
|
||||
pci_write_config_word (bdf, PCI_COMMAND, cmd);
|
||||
pci_read_config_byte (dev, PCI_LATENCY_TIMER, &lat);
|
||||
pci_write_config_word(bdf, PCI_COMMAND, cmd);
|
||||
pci_read_config_byte(dev, PCI_LATENCY_TIMER, &lat);
|
||||
|
||||
if (lat < 16)
|
||||
lat = (64 <= pcibios_max_latency) ? 64 : pcibios_max_latency;
|
||||
else if (lat > pcibios_max_latency)
|
||||
lat = pcibios_max_latency;
|
||||
pci_write_config_byte (dev, PCI_LATENCY_TIMER, lat);
|
||||
pci_write_config_byte(dev, PCI_LATENCY_TIMER, lat);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int
|
||||
sata_bus_probe (int port_no)
|
||||
int sata_bus_probe(int port_no)
|
||||
{
|
||||
int orig_mask, mask;
|
||||
u16 pcs;
|
||||
|
||||
mask = (PORT_PRESENT << port_no);
|
||||
pci_read_config_word (bdf, PCI_PCS, &pcs);
|
||||
pci_read_config_word(bdf, PCI_PCS, &pcs);
|
||||
orig_mask = (int) pcs & 0xff;
|
||||
if ((orig_mask & mask) != mask)
|
||||
return 0;
|
||||
@ -144,10 +143,9 @@ sata_bus_probe (int port_no)
|
||||
return 1;
|
||||
}
|
||||
|
||||
int
|
||||
init_sata (int dev)
|
||||
int init_sata(int dev)
|
||||
{
|
||||
static int done = 0;
|
||||
static int done;
|
||||
u8 i, rv = 0;
|
||||
|
||||
if (!done)
|
||||
@ -155,9 +153,9 @@ init_sata (int dev)
|
||||
else
|
||||
return 0;
|
||||
|
||||
rv = pci_sata_init ();
|
||||
rv = pci_sata_init();
|
||||
if (rv == 1) {
|
||||
printf ("pci initialization failed\n");
|
||||
puts("pci initialization failed\n");
|
||||
return 1;
|
||||
}
|
||||
|
||||
@ -174,19 +172,18 @@ init_sata (int dev)
|
||||
port[1].ioaddr.bmdma_addr = iobase5 + 0x8;
|
||||
|
||||
for (i = 0; i < CONFIG_SYS_SATA_MAXBUS; i++)
|
||||
sata_port (&port[i].ioaddr);
|
||||
sata_port(&port[i].ioaddr);
|
||||
|
||||
for (i = 0; i < CONFIG_SYS_SATA_MAXBUS; i++) {
|
||||
if (!(sata_bus_probe (i))) {
|
||||
if (!(sata_bus_probe(i))) {
|
||||
port[i].port_state = 0;
|
||||
printf ("SATA#%d port is not present \n", i);
|
||||
printf("SATA#%d port is not present\n", i);
|
||||
} else {
|
||||
printf ("SATA#%d port is present\n", i);
|
||||
if (sata_bus_softreset (i)) {
|
||||
printf("SATA#%d port is present\n", i);
|
||||
if (sata_bus_softreset(i))
|
||||
port[i].port_state = 0;
|
||||
} else {
|
||||
else
|
||||
port[i].port_state = 1;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
@ -196,47 +193,43 @@ init_sata (int dev)
|
||||
if (port[i].port_state == 0)
|
||||
continue;
|
||||
for (j = 0; j < CONFIG_SYS_SATA_DEVS_PER_BUS; j++) {
|
||||
sata_identify (i, j);
|
||||
set_Feature_cmd (i, j);
|
||||
sata_identify(i, j);
|
||||
set_Feature_cmd(i, j);
|
||||
devno = i * CONFIG_SYS_SATA_DEVS_PER_BUS + j;
|
||||
if ((sata_dev_desc[devno].lba > 0) &&
|
||||
(sata_dev_desc[devno].blksz > 0)) {
|
||||
dev_print (&sata_dev_desc[devno]);
|
||||
dev_print(&sata_dev_desc[devno]);
|
||||
/* initialize partition type */
|
||||
init_part (&sata_dev_desc[devno]);
|
||||
init_part(&sata_dev_desc[devno]);
|
||||
}
|
||||
}
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
|
||||
static u8 __inline__
|
||||
sata_inb (unsigned long ioaddr)
|
||||
static inline u8 sata_inb(unsigned long ioaddr)
|
||||
{
|
||||
return inb (ioaddr);
|
||||
return inb(ioaddr);
|
||||
}
|
||||
|
||||
static void __inline__
|
||||
sata_outb (unsigned char val, unsigned long ioaddr)
|
||||
static inline void sata_outb(unsigned char val, unsigned long ioaddr)
|
||||
{
|
||||
outb (val, ioaddr);
|
||||
outb(val, ioaddr);
|
||||
}
|
||||
|
||||
static void
|
||||
output_data (struct sata_ioports *ioaddr, ulong * sect_buf, int words)
|
||||
static void output_data(struct sata_ioports *ioaddr, ulong * sect_buf,
|
||||
int words)
|
||||
{
|
||||
outsw (ioaddr->data_addr, sect_buf, words << 1);
|
||||
outsw(ioaddr->data_addr, sect_buf, words << 1);
|
||||
}
|
||||
|
||||
static int
|
||||
input_data (struct sata_ioports *ioaddr, ulong * sect_buf, int words)
|
||||
static int input_data(struct sata_ioports *ioaddr, ulong * sect_buf, int words)
|
||||
{
|
||||
insw (ioaddr->data_addr, sect_buf, words << 1);
|
||||
insw(ioaddr->data_addr, sect_buf, words << 1);
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void
|
||||
sata_cpy (unsigned char *dst, unsigned char *src, unsigned int len)
|
||||
static void sata_cpy(unsigned char *dst, unsigned char *src, unsigned int len)
|
||||
{
|
||||
unsigned char *end, *last;
|
||||
|
||||
@ -257,41 +250,41 @@ sata_cpy (unsigned char *dst, unsigned char *src, unsigned int len)
|
||||
if (*src++ != ' ')
|
||||
last = dst;
|
||||
}
|
||||
OUT:
|
||||
OUT:
|
||||
*last = '\0';
|
||||
}
|
||||
|
||||
int
|
||||
sata_bus_softreset (int num)
|
||||
int sata_bus_softreset(int num)
|
||||
{
|
||||
u8 dev = 0, status = 0, i;
|
||||
|
||||
port[num].dev_mask = 0;
|
||||
|
||||
for (i = 0; i < CONFIG_SYS_SATA_DEVS_PER_BUS; i++) {
|
||||
if (!(sata_devchk (&port[num].ioaddr, i))) {
|
||||
PRINTF ("dev_chk failed for dev#%d\n", i);
|
||||
if (!(sata_devchk(&port[num].ioaddr, i))) {
|
||||
debug("dev_chk failed for dev#%d\n", i);
|
||||
} else {
|
||||
port[num].dev_mask |= (1 << i);
|
||||
PRINTF ("dev_chk passed for dev#%d\n", i);
|
||||
debug("dev_chk passed for dev#%d\n", i);
|
||||
}
|
||||
}
|
||||
|
||||
if (!(port[num].dev_mask)) {
|
||||
printf ("no devices on port%d\n", num);
|
||||
printf("no devices on port%d\n", num);
|
||||
return 1;
|
||||
}
|
||||
|
||||
dev_select (&port[num].ioaddr, dev);
|
||||
dev_select(&port[num].ioaddr, dev);
|
||||
|
||||
port[num].ctl_reg = 0x08; /*Default value of control reg */
|
||||
sata_outb (port[num].ctl_reg, port[num].ioaddr.ctl_addr);
|
||||
udelay (10);
|
||||
sata_outb (port[num].ctl_reg | ATA_SRST, port[num].ioaddr.ctl_addr);
|
||||
udelay (10);
|
||||
sata_outb (port[num].ctl_reg, port[num].ioaddr.ctl_addr);
|
||||
port[num].ctl_reg = 0x08; /* Default value of control reg */
|
||||
sata_outb(port[num].ctl_reg, port[num].ioaddr.ctl_addr);
|
||||
udelay(10);
|
||||
sata_outb(port[num].ctl_reg | ATA_SRST, port[num].ioaddr.ctl_addr);
|
||||
udelay(10);
|
||||
sata_outb(port[num].ctl_reg, port[num].ioaddr.ctl_addr);
|
||||
|
||||
/* spec mandates ">= 2ms" before checking status.
|
||||
/*
|
||||
* spec mandates ">= 2ms" before checking status.
|
||||
* We wait 150ms, because that was the magic delay used for
|
||||
* ATAPI devices in Hale Landis's ATADRVR, for the period of time
|
||||
* between when the ATA command register is written, and then
|
||||
@ -299,38 +292,37 @@ sata_bus_softreset (int num)
|
||||
* checking status is fine, post SRST, we perform this magic
|
||||
* delay here as well.
|
||||
*/
|
||||
msleep (150);
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 300);
|
||||
mdelay(150);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 300);
|
||||
while ((status & ATA_BUSY)) {
|
||||
msleep (100);
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 3);
|
||||
mdelay(100);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 3);
|
||||
}
|
||||
|
||||
if (status & ATA_BUSY)
|
||||
printf ("ata%u is slow to respond,plz be patient\n", num);
|
||||
printf("ata%u is slow to respond,plz be patient\n", num);
|
||||
|
||||
while ((status & ATA_BUSY)) {
|
||||
msleep (100);
|
||||
status = sata_chk_status (&port[num].ioaddr);
|
||||
mdelay(100);
|
||||
status = sata_chk_status(&port[num].ioaddr);
|
||||
}
|
||||
|
||||
if (status & ATA_BUSY) {
|
||||
printf ("ata%u failed to respond : ", num);
|
||||
printf ("bus reset failed\n");
|
||||
printf("ata%u failed to respond : bus reset failed\n", num);
|
||||
return 1;
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
|
||||
void
|
||||
sata_identify (int num, int dev)
|
||||
void sata_identify(int num, int dev)
|
||||
{
|
||||
u8 cmd = 0, status = 0, devno = num * CONFIG_SYS_SATA_DEVS_PER_BUS + dev;
|
||||
u8 cmd = 0, status = 0;
|
||||
u8 devno = num * CONFIG_SYS_SATA_DEVS_PER_BUS + dev;
|
||||
u16 iobuf[ATA_SECT_SIZE];
|
||||
u64 n_sectors = 0;
|
||||
u8 mask = 0;
|
||||
|
||||
memset (iobuf, 0, sizeof (iobuf));
|
||||
memset(iobuf, 0, sizeof(iobuf));
|
||||
hd_driveid_t *iop = (hd_driveid_t *) iobuf;
|
||||
|
||||
if (dev == 0)
|
||||
@ -339,70 +331,67 @@ sata_identify (int num, int dev)
|
||||
mask = 0x02;
|
||||
|
||||
if (!(port[num].dev_mask & mask)) {
|
||||
printf ("dev%d is not present on port#%d\n", dev, num);
|
||||
printf("dev%d is not present on port#%d\n", dev, num);
|
||||
return;
|
||||
}
|
||||
|
||||
printf ("port=%d dev=%d\n", num, dev);
|
||||
printf("port=%d dev=%d\n", num, dev);
|
||||
|
||||
dev_select (&port[num].ioaddr, dev);
|
||||
dev_select(&port[num].ioaddr, dev);
|
||||
|
||||
status = 0;
|
||||
cmd = ATA_CMD_IDENT; /*Device Identify Command */
|
||||
sata_outb (cmd, port[num].ioaddr.command_addr);
|
||||
sata_inb (port[num].ioaddr.altstatus_addr);
|
||||
udelay (10);
|
||||
cmd = ATA_CMD_IDENT; /* Device Identify Command */
|
||||
sata_outb(cmd, port[num].ioaddr.command_addr);
|
||||
sata_inb(port[num].ioaddr.altstatus_addr);
|
||||
udelay(10);
|
||||
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 1000);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 1000);
|
||||
if (status & ATA_ERR) {
|
||||
printf ("\ndevice not responding\n");
|
||||
puts("\ndevice not responding\n");
|
||||
port[num].dev_mask &= ~mask;
|
||||
return;
|
||||
}
|
||||
|
||||
input_data (&port[num].ioaddr, (ulong *) iobuf, ATA_SECTORWORDS);
|
||||
input_data(&port[num].ioaddr, (ulong *) iobuf, ATA_SECTORWORDS);
|
||||
|
||||
PRINTF ("\nata%u: dev %u cfg 49:%04x 82:%04x 83:%04x 84:%04x85:%04x"
|
||||
debug("\nata%u: dev %u cfg 49:%04x 82:%04x 83:%04x 84:%04x85:%04x"
|
||||
"86:%04x" "87:%04x 88:%04x\n", num, dev, iobuf[49],
|
||||
iobuf[82], iobuf[83], iobuf[84], iobuf[85], iobuf[86],
|
||||
iobuf[87], iobuf[88]);
|
||||
|
||||
/* we require LBA and DMA support (bits 8 & 9 of word 49) */
|
||||
if (!ata_id_has_dma (iobuf) || !ata_id_has_lba (iobuf)) {
|
||||
PRINTF ("ata%u: no dma/lba\n", num);
|
||||
}
|
||||
ata_dump_id (iobuf);
|
||||
if (!ata_id_has_dma(iobuf) || !ata_id_has_lba(iobuf))
|
||||
debug("ata%u: no dma/lba\n", num);
|
||||
ata_dump_id(iobuf);
|
||||
|
||||
if (ata_id_has_lba48 (iobuf)) {
|
||||
n_sectors = ata_id_u64 (iobuf, 100);
|
||||
} else {
|
||||
n_sectors = ata_id_u32 (iobuf, 60);
|
||||
}
|
||||
PRINTF ("no. of sectors %u\n", ata_id_u64 (iobuf, 100));
|
||||
PRINTF ("no. of sectors %u\n", ata_id_u32 (iobuf, 60));
|
||||
if (ata_id_has_lba48(iobuf))
|
||||
n_sectors = ata_id_u64(iobuf, 100);
|
||||
else
|
||||
n_sectors = ata_id_u32(iobuf, 60);
|
||||
debug("no. of sectors %u\n", ata_id_u64(iobuf, 100));
|
||||
debug("no. of sectors %u\n", ata_id_u32(iobuf, 60));
|
||||
|
||||
if (n_sectors == 0) {
|
||||
port[num].dev_mask &= ~mask;
|
||||
return;
|
||||
}
|
||||
|
||||
sata_cpy ((unsigned char *)sata_dev_desc[devno].revision, iop->fw_rev,
|
||||
sizeof (sata_dev_desc[devno].revision));
|
||||
sata_cpy ((unsigned char *)sata_dev_desc[devno].vendor, iop->model,
|
||||
sizeof (sata_dev_desc[devno].vendor));
|
||||
sata_cpy ((unsigned char *)sata_dev_desc[devno].product, iop->serial_no,
|
||||
sizeof (sata_dev_desc[devno].product));
|
||||
strswab (sata_dev_desc[devno].revision);
|
||||
strswab (sata_dev_desc[devno].vendor);
|
||||
sata_cpy((unsigned char *)sata_dev_desc[devno].revision, iop->fw_rev,
|
||||
sizeof(sata_dev_desc[devno].revision));
|
||||
sata_cpy((unsigned char *)sata_dev_desc[devno].vendor, iop->model,
|
||||
sizeof(sata_dev_desc[devno].vendor));
|
||||
sata_cpy((unsigned char *)sata_dev_desc[devno].product, iop->serial_no,
|
||||
sizeof(sata_dev_desc[devno].product));
|
||||
strswab(sata_dev_desc[devno].revision);
|
||||
strswab(sata_dev_desc[devno].vendor);
|
||||
|
||||
if ((iop->config & 0x0080) == 0x0080) {
|
||||
if ((iop->config & 0x0080) == 0x0080)
|
||||
sata_dev_desc[devno].removable = 1;
|
||||
} else {
|
||||
else
|
||||
sata_dev_desc[devno].removable = 0;
|
||||
}
|
||||
|
||||
sata_dev_desc[devno].lba = iop->lba_capacity;
|
||||
PRINTF ("lba=0x%x", sata_dev_desc[devno].lba);
|
||||
debug("lba=0x%x", sata_dev_desc[devno].lba);
|
||||
|
||||
#ifdef CONFIG_LBA48
|
||||
if (iop->command_set_2 & 0x0400) {
|
||||
@ -422,8 +411,7 @@ sata_identify (int num, int dev)
|
||||
sata_dev_desc[devno].lun = 0; /* just to fill something in... */
|
||||
}
|
||||
|
||||
void
|
||||
set_Feature_cmd (int num, int dev)
|
||||
void set_Feature_cmd(int num, int dev)
|
||||
{
|
||||
u8 mask = 0x00, status = 0;
|
||||
|
||||
@ -433,33 +421,32 @@ set_Feature_cmd (int num, int dev)
|
||||
mask = 0x02;
|
||||
|
||||
if (!(port[num].dev_mask & mask)) {
|
||||
PRINTF ("dev%d is not present on port#%d\n", dev, num);
|
||||
debug("dev%d is not present on port#%d\n", dev, num);
|
||||
return;
|
||||
}
|
||||
|
||||
dev_select (&port[num].ioaddr, dev);
|
||||
dev_select(&port[num].ioaddr, dev);
|
||||
|
||||
sata_outb (SETFEATURES_XFER, port[num].ioaddr.feature_addr);
|
||||
sata_outb (XFER_PIO_4, port[num].ioaddr.nsect_addr);
|
||||
sata_outb (0, port[num].ioaddr.lbal_addr);
|
||||
sata_outb (0, port[num].ioaddr.lbam_addr);
|
||||
sata_outb (0, port[num].ioaddr.lbah_addr);
|
||||
sata_outb(SETFEATURES_XFER, port[num].ioaddr.feature_addr);
|
||||
sata_outb(XFER_PIO_4, port[num].ioaddr.nsect_addr);
|
||||
sata_outb(0, port[num].ioaddr.lbal_addr);
|
||||
sata_outb(0, port[num].ioaddr.lbam_addr);
|
||||
sata_outb(0, port[num].ioaddr.lbah_addr);
|
||||
|
||||
sata_outb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr);
|
||||
sata_outb (ATA_CMD_SETF, port[num].ioaddr.command_addr);
|
||||
sata_outb(ATA_DEVICE_OBS, port[num].ioaddr.device_addr);
|
||||
sata_outb(ATA_CMD_SETF, port[num].ioaddr.command_addr);
|
||||
|
||||
udelay (50);
|
||||
msleep (150);
|
||||
udelay(50);
|
||||
mdelay(150);
|
||||
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 5000);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 5000);
|
||||
if ((status & (ATA_STAT_BUSY | ATA_STAT_ERR))) {
|
||||
printf ("Error : status 0x%02x\n", status);
|
||||
printf("Error : status 0x%02x\n", status);
|
||||
port[num].dev_mask &= ~mask;
|
||||
}
|
||||
}
|
||||
|
||||
void
|
||||
sata_port (struct sata_ioports *ioport)
|
||||
void sata_port(struct sata_ioports *ioport)
|
||||
{
|
||||
ioport->data_addr = ioport->cmd_addr + ATA_REG_DATA;
|
||||
ioport->error_addr = ioport->cmd_addr + ATA_REG_ERR;
|
||||
@ -473,24 +460,23 @@ sata_port (struct sata_ioports *ioport)
|
||||
ioport->command_addr = ioport->cmd_addr + ATA_REG_CMD;
|
||||
}
|
||||
|
||||
int
|
||||
sata_devchk (struct sata_ioports *ioaddr, int dev)
|
||||
int sata_devchk(struct sata_ioports *ioaddr, int dev)
|
||||
{
|
||||
u8 nsect, lbal;
|
||||
|
||||
dev_select (ioaddr, dev);
|
||||
dev_select(ioaddr, dev);
|
||||
|
||||
sata_outb (0x55, ioaddr->nsect_addr);
|
||||
sata_outb (0xaa, ioaddr->lbal_addr);
|
||||
sata_outb(0x55, ioaddr->nsect_addr);
|
||||
sata_outb(0xaa, ioaddr->lbal_addr);
|
||||
|
||||
sata_outb (0xaa, ioaddr->nsect_addr);
|
||||
sata_outb (0x55, ioaddr->lbal_addr);
|
||||
sata_outb(0xaa, ioaddr->nsect_addr);
|
||||
sata_outb(0x55, ioaddr->lbal_addr);
|
||||
|
||||
sata_outb (0x55, ioaddr->nsect_addr);
|
||||
sata_outb (0xaa, ioaddr->lbal_addr);
|
||||
sata_outb(0x55, ioaddr->nsect_addr);
|
||||
sata_outb(0xaa, ioaddr->lbal_addr);
|
||||
|
||||
nsect = sata_inb (ioaddr->nsect_addr);
|
||||
lbal = sata_inb (ioaddr->lbal_addr);
|
||||
nsect = sata_inb(ioaddr->nsect_addr);
|
||||
lbal = sata_inb(ioaddr->lbal_addr);
|
||||
|
||||
if ((nsect == 0x55) && (lbal == 0xaa))
|
||||
return 1; /* we found a device */
|
||||
@ -498,8 +484,7 @@ sata_devchk (struct sata_ioports *ioaddr, int dev)
|
||||
return 0; /* nothing found */
|
||||
}
|
||||
|
||||
void
|
||||
dev_select (struct sata_ioports *ioaddr, int dev)
|
||||
void dev_select(struct sata_ioports *ioaddr, int dev)
|
||||
{
|
||||
u8 tmp = 0;
|
||||
|
||||
@ -508,42 +493,31 @@ dev_select (struct sata_ioports *ioaddr, int dev)
|
||||
else
|
||||
tmp = ATA_DEVICE_OBS | ATA_DEV1;
|
||||
|
||||
sata_outb (tmp, ioaddr->device_addr);
|
||||
sata_inb (ioaddr->altstatus_addr);
|
||||
udelay (5);
|
||||
sata_outb(tmp, ioaddr->device_addr);
|
||||
sata_inb(ioaddr->altstatus_addr);
|
||||
udelay(5);
|
||||
}
|
||||
|
||||
u8
|
||||
sata_busy_wait (struct sata_ioports *ioaddr, int bits, unsigned int max)
|
||||
u8 sata_busy_wait(struct sata_ioports *ioaddr, int bits, unsigned int max)
|
||||
{
|
||||
u8 status;
|
||||
|
||||
do {
|
||||
udelay (1000);
|
||||
status = sata_chk_status (ioaddr);
|
||||
udelay(1000);
|
||||
status = sata_chk_status(ioaddr);
|
||||
max--;
|
||||
} while ((status & bits) && (max > 0));
|
||||
|
||||
return status;
|
||||
}
|
||||
|
||||
u8
|
||||
sata_chk_status (struct sata_ioports * ioaddr)
|
||||
u8 sata_chk_status(struct sata_ioports *ioaddr)
|
||||
{
|
||||
return sata_inb (ioaddr->status_addr);
|
||||
return sata_inb(ioaddr->status_addr);
|
||||
}
|
||||
|
||||
void
|
||||
msleep (int count)
|
||||
{
|
||||
int i;
|
||||
|
||||
for (i = 0; i < count; i++)
|
||||
udelay (1000);
|
||||
}
|
||||
|
||||
ulong
|
||||
sata_read (int device, ulong blknr,lbaint_t blkcnt, void * buff)
|
||||
ulong sata_read(int device, ulong blknr, lbaint_t blkcnt, void *buff)
|
||||
{
|
||||
ulong n = 0, *buffer = (ulong *)buff;
|
||||
u8 dev = 0, num = 0, mask = 0, status = 0;
|
||||
@ -553,16 +527,16 @@ sata_read (int device, ulong blknr,lbaint_t blkcnt, void * buff)
|
||||
|
||||
if (blknr & 0x0000fffff0000000) {
|
||||
if (!sata_dev_desc[devno].lba48) {
|
||||
printf ("Drive doesn't support 48-bit addressing\n");
|
||||
printf("Drive doesn't support 48-bit addressing\n");
|
||||
return 0;
|
||||
}
|
||||
/* more than 28 bits used, use 48bit mode */
|
||||
lba48 = 1;
|
||||
}
|
||||
#endif
|
||||
/*Port Number */
|
||||
/* Port Number */
|
||||
num = device / CONFIG_SYS_SATA_DEVS_PER_BUS;
|
||||
/*dev on the port */
|
||||
/* dev on the port */
|
||||
if (device >= CONFIG_SYS_SATA_DEVS_PER_BUS)
|
||||
dev = device - CONFIG_SYS_SATA_DEVS_PER_BUS;
|
||||
else
|
||||
@ -574,73 +548,73 @@ sata_read (int device, ulong blknr,lbaint_t blkcnt, void * buff)
|
||||
mask = 0x02;
|
||||
|
||||
if (!(port[num].dev_mask & mask)) {
|
||||
printf ("dev%d is not present on port#%d\n", dev, num);
|
||||
printf("dev%d is not present on port#%d\n", dev, num);
|
||||
return 0;
|
||||
}
|
||||
|
||||
/* Select device */
|
||||
dev_select (&port[num].ioaddr, dev);
|
||||
dev_select(&port[num].ioaddr, dev);
|
||||
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 500);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 500);
|
||||
if (status & ATA_BUSY) {
|
||||
printf ("ata%u failed to respond\n", port[num].port_no);
|
||||
printf("ata%u failed to respond\n", port[num].port_no);
|
||||
return n;
|
||||
}
|
||||
while (blkcnt-- > 0) {
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 500);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 500);
|
||||
if (status & ATA_BUSY) {
|
||||
printf ("ata%u failed to respond\n", 0);
|
||||
printf("ata%u failed to respond\n", 0);
|
||||
return n;
|
||||
}
|
||||
#ifdef CONFIG_LBA48
|
||||
if (lba48) {
|
||||
/* write high bits */
|
||||
sata_outb (0, port[num].ioaddr.nsect_addr);
|
||||
sata_outb ((blknr >> 24) & 0xFF,
|
||||
sata_outb(0, port[num].ioaddr.nsect_addr);
|
||||
sata_outb((blknr >> 24) & 0xFF,
|
||||
port[num].ioaddr.lbal_addr);
|
||||
sata_outb ((blknr >> 32) & 0xFF,
|
||||
sata_outb((blknr >> 32) & 0xFF,
|
||||
port[num].ioaddr.lbam_addr);
|
||||
sata_outb ((blknr >> 40) & 0xFF,
|
||||
sata_outb((blknr >> 40) & 0xFF,
|
||||
port[num].ioaddr.lbah_addr);
|
||||
}
|
||||
#endif
|
||||
sata_outb (1, port[num].ioaddr.nsect_addr);
|
||||
sata_outb (((blknr) >> 0) & 0xFF,
|
||||
sata_outb(1, port[num].ioaddr.nsect_addr);
|
||||
sata_outb(((blknr) >> 0) & 0xFF,
|
||||
port[num].ioaddr.lbal_addr);
|
||||
sata_outb ((blknr >> 8) & 0xFF, port[num].ioaddr.lbam_addr);
|
||||
sata_outb ((blknr >> 16) & 0xFF, port[num].ioaddr.lbah_addr);
|
||||
sata_outb((blknr >> 8) & 0xFF, port[num].ioaddr.lbam_addr);
|
||||
sata_outb((blknr >> 16) & 0xFF, port[num].ioaddr.lbah_addr);
|
||||
|
||||
#ifdef CONFIG_LBA48
|
||||
if (lba48) {
|
||||
sata_outb (ATA_LBA, port[num].ioaddr.device_addr);
|
||||
sata_outb (ATA_CMD_READ_EXT,
|
||||
sata_outb(ATA_LBA, port[num].ioaddr.device_addr);
|
||||
sata_outb(ATA_CMD_READ_EXT,
|
||||
port[num].ioaddr.command_addr);
|
||||
} else
|
||||
#endif
|
||||
{
|
||||
sata_outb (ATA_LBA | ((blknr >> 24) & 0xF),
|
||||
sata_outb(ATA_LBA | ((blknr >> 24) & 0xF),
|
||||
port[num].ioaddr.device_addr);
|
||||
sata_outb (ATA_CMD_READ,
|
||||
sata_outb(ATA_CMD_READ,
|
||||
port[num].ioaddr.command_addr);
|
||||
}
|
||||
|
||||
msleep (50);
|
||||
/*may take up to 4 sec */
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 4000);
|
||||
mdelay(50);
|
||||
/* may take up to 4 sec */
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 4000);
|
||||
|
||||
if ((status & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR))
|
||||
!= ATA_STAT_DRQ) {
|
||||
u8 err = 0;
|
||||
|
||||
printf ("Error no DRQ dev %d blk %ld: sts 0x%02x\n",
|
||||
printf("Error no DRQ dev %d blk %ld: sts 0x%02x\n",
|
||||
device, (ulong) blknr, status);
|
||||
err = sata_inb (port[num].ioaddr.error_addr);
|
||||
printf ("Error reg = 0x%x\n", err);
|
||||
return (n);
|
||||
err = sata_inb(port[num].ioaddr.error_addr);
|
||||
printf("Error reg = 0x%x\n", err);
|
||||
return n;
|
||||
}
|
||||
input_data (&port[num].ioaddr, buffer, ATA_SECTORWORDS);
|
||||
sata_inb (port[num].ioaddr.altstatus_addr);
|
||||
udelay (50);
|
||||
input_data(&port[num].ioaddr, buffer, ATA_SECTORWORDS);
|
||||
sata_inb(port[num].ioaddr.altstatus_addr);
|
||||
udelay(50);
|
||||
|
||||
++n;
|
||||
++blknr;
|
||||
@ -649,8 +623,7 @@ sata_read (int device, ulong blknr,lbaint_t blkcnt, void * buff)
|
||||
return n;
|
||||
}
|
||||
|
||||
ulong
|
||||
sata_write (int device, ulong blknr,lbaint_t blkcnt, void * buff)
|
||||
ulong sata_write(int device, ulong blknr, lbaint_t blkcnt, void *buff)
|
||||
{
|
||||
ulong n = 0, *buffer = (ulong *)buff;
|
||||
unsigned char status = 0, num = 0, dev = 0, mask = 0;
|
||||
@ -660,16 +633,16 @@ sata_write (int device, ulong blknr,lbaint_t blkcnt, void * buff)
|
||||
|
||||
if (blknr & 0x0000fffff0000000) {
|
||||
if (!sata_dev_desc[devno].lba48) {
|
||||
printf ("Drive doesn't support 48-bit addressing\n");
|
||||
printf("Drive doesn't support 48-bit addressing\n");
|
||||
return 0;
|
||||
}
|
||||
/* more than 28 bits used, use 48bit mode */
|
||||
lba48 = 1;
|
||||
}
|
||||
#endif
|
||||
/*Port Number */
|
||||
/* Port Number */
|
||||
num = device / CONFIG_SYS_SATA_DEVS_PER_BUS;
|
||||
/*dev on the Port */
|
||||
/* dev on the Port */
|
||||
if (device >= CONFIG_SYS_SATA_DEVS_PER_BUS)
|
||||
dev = device - CONFIG_SYS_SATA_DEVS_PER_BUS;
|
||||
else
|
||||
@ -681,64 +654,64 @@ sata_write (int device, ulong blknr,lbaint_t blkcnt, void * buff)
|
||||
mask = 0x02;
|
||||
|
||||
/* Select device */
|
||||
dev_select (&port[num].ioaddr, dev);
|
||||
dev_select(&port[num].ioaddr, dev);
|
||||
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 500);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 500);
|
||||
if (status & ATA_BUSY) {
|
||||
printf ("ata%u failed to respond\n", port[num].port_no);
|
||||
printf("ata%u failed to respond\n", port[num].port_no);
|
||||
return n;
|
||||
}
|
||||
|
||||
while (blkcnt-- > 0) {
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 500);
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 500);
|
||||
if (status & ATA_BUSY) {
|
||||
printf ("ata%u failed to respond\n",
|
||||
printf("ata%u failed to respond\n",
|
||||
port[num].port_no);
|
||||
return n;
|
||||
}
|
||||
#ifdef CONFIG_LBA48
|
||||
if (lba48) {
|
||||
/* write high bits */
|
||||
sata_outb (0, port[num].ioaddr.nsect_addr);
|
||||
sata_outb ((blknr >> 24) & 0xFF,
|
||||
sata_outb(0, port[num].ioaddr.nsect_addr);
|
||||
sata_outb((blknr >> 24) & 0xFF,
|
||||
port[num].ioaddr.lbal_addr);
|
||||
sata_outb ((blknr >> 32) & 0xFF,
|
||||
sata_outb((blknr >> 32) & 0xFF,
|
||||
port[num].ioaddr.lbam_addr);
|
||||
sata_outb ((blknr >> 40) & 0xFF,
|
||||
sata_outb((blknr >> 40) & 0xFF,
|
||||
port[num].ioaddr.lbah_addr);
|
||||
}
|
||||
#endif
|
||||
sata_outb (1, port[num].ioaddr.nsect_addr);
|
||||
sata_outb ((blknr >> 0) & 0xFF, port[num].ioaddr.lbal_addr);
|
||||
sata_outb ((blknr >> 8) & 0xFF, port[num].ioaddr.lbam_addr);
|
||||
sata_outb ((blknr >> 16) & 0xFF, port[num].ioaddr.lbah_addr);
|
||||
sata_outb(1, port[num].ioaddr.nsect_addr);
|
||||
sata_outb((blknr >> 0) & 0xFF, port[num].ioaddr.lbal_addr);
|
||||
sata_outb((blknr >> 8) & 0xFF, port[num].ioaddr.lbam_addr);
|
||||
sata_outb((blknr >> 16) & 0xFF, port[num].ioaddr.lbah_addr);
|
||||
#ifdef CONFIG_LBA48
|
||||
if (lba48) {
|
||||
sata_outb (ATA_LBA, port[num].ioaddr.device_addr);
|
||||
sata_outb (ATA_CMD_WRITE_EXT,
|
||||
sata_outb(ATA_LBA, port[num].ioaddr.device_addr);
|
||||
sata_outb(ATA_CMD_WRITE_EXT,
|
||||
port[num].ioaddr.command_addr);
|
||||
} else
|
||||
#endif
|
||||
{
|
||||
sata_outb (ATA_LBA | ((blknr >> 24) & 0xF),
|
||||
sata_outb(ATA_LBA | ((blknr >> 24) & 0xF),
|
||||
port[num].ioaddr.device_addr);
|
||||
sata_outb (ATA_CMD_WRITE,
|
||||
sata_outb(ATA_CMD_WRITE,
|
||||
port[num].ioaddr.command_addr);
|
||||
}
|
||||
|
||||
msleep (50);
|
||||
/*may take up to 4 sec */
|
||||
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 4000);
|
||||
mdelay(50);
|
||||
/* may take up to 4 sec */
|
||||
status = sata_busy_wait(&port[num].ioaddr, ATA_BUSY, 4000);
|
||||
if ((status & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR))
|
||||
!= ATA_STAT_DRQ) {
|
||||
printf ("Error no DRQ dev %d blk %ld: sts 0x%02x\n",
|
||||
printf("Error no DRQ dev %d blk %ld: sts 0x%02x\n",
|
||||
device, (ulong) blknr, status);
|
||||
return (n);
|
||||
return n;
|
||||
}
|
||||
|
||||
output_data (&port[num].ioaddr, buffer, ATA_SECTORWORDS);
|
||||
sata_inb (port[num].ioaddr.altstatus_addr);
|
||||
udelay (50);
|
||||
output_data(&port[num].ioaddr, buffer, ATA_SECTORWORDS);
|
||||
sata_inb(port[num].ioaddr.altstatus_addr);
|
||||
udelay(50);
|
||||
|
||||
++n;
|
||||
++blknr;
|
||||
|
||||
@ -1,12 +1,6 @@
|
||||
#ifndef __ATA_PIIX_H__
|
||||
#define __ATA_PIIX_H__
|
||||
|
||||
#if (DEBUG_SATA)
|
||||
#define PRINTF(fmt,args...) printf (fmt ,##args)
|
||||
#else
|
||||
#define PRINTF(fmt,args...)
|
||||
#endif
|
||||
|
||||
struct sata_ioports {
|
||||
unsigned long cmd_addr;
|
||||
unsigned long data_addr;
|
||||
@ -36,45 +30,43 @@ struct sata_port {
|
||||
};
|
||||
|
||||
/***********SATA LIBRARY SPECIFIC DEFINITIONS AND DECLARATIONS**************/
|
||||
#ifdef SATA_DECL /*SATA library specific declarations */
|
||||
inline void
|
||||
ata_dump_id (u16 * id)
|
||||
#ifdef SATA_DECL /* SATA library specific declarations */
|
||||
inline void ata_dump_id(u16 *id)
|
||||
{
|
||||
PRINTF ("49 = 0x%04x "
|
||||
debug("49 = 0x%04x "
|
||||
"53 = 0x%04x "
|
||||
"63 = 0x%04x "
|
||||
"64 = 0x%04x "
|
||||
"75 = 0x%04x \n", id[49], id[53], id[63], id[64], id[75]);
|
||||
PRINTF ("80 = 0x%04x "
|
||||
"75 = 0x%04x\n", id[49], id[53], id[63], id[64], id[75]);
|
||||
debug("80 = 0x%04x "
|
||||
"81 = 0x%04x "
|
||||
"82 = 0x%04x "
|
||||
"83 = 0x%04x "
|
||||
"84 = 0x%04x \n", id[80], id[81], id[82], id[83], id[84]);
|
||||
PRINTF ("88 = 0x%04x " "93 = 0x%04x\n", id[88], id[93]);
|
||||
"84 = 0x%04x\n", id[80], id[81], id[82], id[83], id[84]);
|
||||
debug("88 = 0x%04x " "93 = 0x%04x\n", id[88], id[93]);
|
||||
}
|
||||
#endif
|
||||
|
||||
#ifdef SATA_DECL /*SATA library specific declarations */
|
||||
int sata_bus_softreset (int num);
|
||||
void sata_identify (int num, int dev);
|
||||
void sata_port (struct sata_ioports *ioport);
|
||||
void set_Feature_cmd (int num, int dev);
|
||||
int sata_devchk (struct sata_ioports *ioaddr, int dev);
|
||||
void dev_select (struct sata_ioports *ioaddr, int dev);
|
||||
u8 sata_busy_wait (struct sata_ioports *ioaddr, int bits, unsigned int max);
|
||||
u8 sata_chk_status (struct sata_ioports *ioaddr);
|
||||
ulong sata_read (int device, ulong blknr,lbaint_t blkcnt, void * buffer);
|
||||
ulong sata_write (int device,ulong blknr, lbaint_t blkcnt, void * buffer);
|
||||
void msleep (int count);
|
||||
int sata_bus_softreset(int num);
|
||||
void sata_identify(int num, int dev);
|
||||
void sata_port(struct sata_ioports *ioport);
|
||||
void set_Feature_cmd(int num, int dev);
|
||||
int sata_devchk(struct sata_ioports *ioaddr, int dev);
|
||||
void dev_select(struct sata_ioports *ioaddr, int dev);
|
||||
u8 sata_busy_wait(struct sata_ioports *ioaddr, int bits, unsigned int max);
|
||||
u8 sata_chk_status(struct sata_ioports *ioaddr);
|
||||
ulong sata_read(int device, ulong blknr,lbaint_t blkcnt, void *buffer);
|
||||
ulong sata_write(int device,ulong blknr, lbaint_t blkcnt, void *buffer);
|
||||
#endif
|
||||
|
||||
/************DRIVER SPECIFIC DEFINITIONS AND DECLARATIONS**************/
|
||||
|
||||
#ifdef DRV_DECL /*Driver specific declaration */
|
||||
int init_sata (int dev);
|
||||
#ifdef DRV_DECL /* Driver specific declaration */
|
||||
int init_sata(int dev);
|
||||
#endif
|
||||
|
||||
#ifdef DRV_DECL /*Defines Driver Specific variables */
|
||||
#ifdef DRV_DECL /* Defines Driver Specific variables */
|
||||
struct sata_port port[CONFIG_SYS_SATA_MAXBUS];
|
||||
#endif
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user