arm: Remove mv88f6281gtw_ge board
This board has not been converted to generic board by the deadline. Remove it. Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is contained in:
Simon Glass
Tom Rini
parent
9f840b8d56
commit
7cd768cf2c
@ -7,9 +7,6 @@ choice
|
||||
config TARGET_OPENRD
|
||||
bool "Marvell OpenRD Board"
|
||||
|
||||
config TARGET_MV88F6281GTW_GE
|
||||
bool "MV88f6281GTW_GE Board"
|
||||
|
||||
config TARGET_RD6281A
|
||||
bool "RD6281A Board"
|
||||
|
||||
@ -67,7 +64,6 @@ config SYS_SOC
|
||||
default "kirkwood"
|
||||
|
||||
source "board/Marvell/openrd/Kconfig"
|
||||
source "board/Marvell/mv88f6281gtw_ge/Kconfig"
|
||||
source "board/Marvell/rd6281a/Kconfig"
|
||||
source "board/Marvell/dreamplug/Kconfig"
|
||||
source "board/Marvell/guruplug/Kconfig"
|
||||
|
||||
@ -1,12 +0,0 @@
|
||||
if TARGET_MV88F6281GTW_GE
|
||||
|
||||
config SYS_BOARD
|
||||
default "mv88f6281gtw_ge"
|
||||
|
||||
config SYS_VENDOR
|
||||
default "Marvell"
|
||||
|
||||
config SYS_CONFIG_NAME
|
||||
default "mv88f6281gtw_ge"
|
||||
|
||||
endif
|
||||
@ -1,6 +0,0 @@
|
||||
MV88F6281GTW_GE BOARD
|
||||
M: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
S: Maintained
|
||||
F: board/Marvell/mv88f6281gtw_ge/
|
||||
F: include/configs/mv88f6281gtw_ge.h
|
||||
F: configs/mv88f6281gtw_ge_defconfig
|
||||
@ -1,9 +0,0 @@
|
||||
#
|
||||
# (C) Copyright 2009
|
||||
# Marvell Semiconductor <www.marvell.com>
|
||||
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
|
||||
obj-y := mv88f6281gtw_ge.o
|
||||
@ -1,149 +0,0 @@
|
||||
#
|
||||
# (C) Copyright 2009
|
||||
# Marvell Semiconductor <www.marvell.com>
|
||||
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
# Refer doc/README.kwbimage for more details about how-to configure
|
||||
# and create kirkwood boot image
|
||||
#
|
||||
|
||||
# Boot Media configurations
|
||||
BOOT_FROM spi # Boot from SPI flash
|
||||
|
||||
# SOC registers configuration using bootrom header extension
|
||||
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
|
||||
|
||||
# Configure RGMII-0 interface pad voltage to 1.8V
|
||||
DATA 0xFFD100e0 0x1b1b1b9b
|
||||
|
||||
#Dram initalization for SINGLE x16 CL=5 @ 400MHz
|
||||
DATA 0xFFD01400 0x43000a00 # DDR Configuration register
|
||||
# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
|
||||
# bit23-14: zero
|
||||
# bit24: 1= enable exit self refresh mode on DDR access
|
||||
# bit25: 1 required
|
||||
# bit29-26: zero
|
||||
# bit31-30: 01
|
||||
|
||||
DATA 0xFFD01404 0x38543000 # DDR Controller Control Low
|
||||
# bit 4: 0=addr/cmd in smame cycle
|
||||
# bit 5: 0=clk is driven during self refresh, we don't care for APX
|
||||
# bit 6: 0=use recommended falling edge of clk for addr/cmd
|
||||
# bit14: 0=input buffer always powered up
|
||||
# bit18: 1=cpu lock transaction enabled
|
||||
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
|
||||
# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
|
||||
# bit30-28: 3 required
|
||||
# bit31: 0=no additional STARTBURST delay
|
||||
|
||||
DATA 0xFFD01408 0x2202433D # DDR Timing (Low) (active cycles value +1)
|
||||
# bit3-0: TRAS lsbs
|
||||
# bit7-4: TRCD
|
||||
# bit11- 8: TRP
|
||||
# bit15-12: TWR
|
||||
# bit19-16: TWTR
|
||||
# bit20: TRAS msb
|
||||
# bit23-21: 0x0
|
||||
# bit27-24: TRRD
|
||||
# bit31-28: TRTP
|
||||
|
||||
DATA 0xFFD0140C 0x0000002A # DDR Timing (High)
|
||||
# bit6-0: TRFC
|
||||
# bit8-7: TR2R
|
||||
# bit10-9: TR2W
|
||||
# bit12-11: TW2W
|
||||
# bit31-13: zero required
|
||||
|
||||
DATA 0xFFD01410 0x0000000D # DDR Address Control
|
||||
# bit1-0: 01, Cs0width=x16
|
||||
# bit3-2: 11, Cs0size=1Gb
|
||||
# bit5-4: 00, Cs2width=nonexistent
|
||||
# bit7-6: 00, Cs1size =nonexistent
|
||||
# bit9-8: 00, Cs2width=nonexistent
|
||||
# bit11-10: 00, Cs2size =nonexistent
|
||||
# bit13-12: 00, Cs3width=nonexistent
|
||||
# bit15-14: 00, Cs3size =nonexistent
|
||||
# bit16: 0, Cs0AddrSel
|
||||
# bit17: 0, Cs1AddrSel
|
||||
# bit18: 0, Cs2AddrSel
|
||||
# bit19: 0, Cs3AddrSel
|
||||
# bit31-20: 0 required
|
||||
|
||||
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
|
||||
# bit0: 0, OpenPage enabled
|
||||
# bit31-1: 0 required
|
||||
|
||||
DATA 0xFFD01418 0x00000000 # DDR Operation
|
||||
# bit3-0: 0x0, DDR cmd
|
||||
# bit31-4: 0 required
|
||||
|
||||
DATA 0xFFD0141C 0x00000C52 # DDR Mode
|
||||
# bit2-0: 2, BurstLen=2 required
|
||||
# bit3: 0, BurstType=0 required
|
||||
# bit6-4: 4, CL=5
|
||||
# bit7: 0, TestMode=0 normal
|
||||
# bit8: 0, DLL reset=0 normal
|
||||
# bit11-9: 6, auto-precharge write recovery ????????????
|
||||
# bit12: 0, PD must be zero
|
||||
# bit31-13: 0 required
|
||||
|
||||
DATA 0xFFD01420 0x00000046 # DDR Extended Mode
|
||||
# bit0: 0, DDR DLL enabled
|
||||
# bit1: 1, DDR drive strenght reduced
|
||||
# bit2: 1, DDR ODT control lsd enabled
|
||||
# bit5-3: 000, required
|
||||
# bit6: 1, DDR ODT control msb, enabled
|
||||
# bit9-7: 000, required
|
||||
# bit10: 0, differential DQS enabled
|
||||
# bit11: 0, required
|
||||
# bit12: 0, DDR output buffer enabled
|
||||
# bit31-13: 0 required
|
||||
|
||||
DATA 0xFFD01424 0x0000F1FF # DDR Controller Control High
|
||||
# bit2-0: 111, required
|
||||
# bit3 : 1 , MBUS Burst Chop disabled
|
||||
# bit6-4: 111, required
|
||||
# bit7 : 1 , D2P Latency enabled
|
||||
# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
|
||||
# bit9 : 0 , no half clock cycle addition to dataout
|
||||
# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
|
||||
# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
|
||||
# bit15-12: 1111 required
|
||||
# bit31-16: 0 required
|
||||
|
||||
DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
|
||||
DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
|
||||
|
||||
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
|
||||
DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
|
||||
# bit0: 1, Window enabled
|
||||
# bit1: 0, Write Protect disabled
|
||||
# bit3-2: 00, CS0 hit selected
|
||||
# bit23-4: ones, required
|
||||
# bit31-24: 0x07, Size (i.e. 128MB)
|
||||
|
||||
DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
|
||||
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
|
||||
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
|
||||
|
||||
DATA 0xFFD01494 0x00010001 # DDR ODT Control (Low)
|
||||
# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
|
||||
# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
|
||||
|
||||
DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
|
||||
# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
|
||||
# bit3-2: 01, ODT1 active NEVER!
|
||||
# bit31-4: zero, required
|
||||
|
||||
DATA 0xFFD0149C 0x0000E811 # CPU ODT Control
|
||||
# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
|
||||
# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
|
||||
# bit11-10:1, DQ_ODTSel. ODT select turned on
|
||||
|
||||
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
|
||||
#bit0=1, enable DDR init upon this register write
|
||||
|
||||
# End of Header extension
|
||||
DATA 0x0 0x0
|
||||
@ -1,119 +0,0 @@
|
||||
/*
|
||||
* Maintainer : Prafulla Wadaskar <prafulla@marvell.com>
|
||||
*
|
||||
* (C) Copyright 2009
|
||||
* Marvell Semiconductor <www.marvell.com>
|
||||
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <netdev.h>
|
||||
#include <asm/arch/cpu.h>
|
||||
#include <asm/arch/soc.h>
|
||||
#include <asm/arch/mpp.h>
|
||||
#include "mv88f6281gtw_ge.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
int board_early_init_f(void)
|
||||
{
|
||||
/*
|
||||
* default gpio configuration
|
||||
* There are maximum 64 gpios controlled through 2 sets of registers
|
||||
* the below configuration configures mainly initial LED status
|
||||
*/
|
||||
mvebu_config_gpio(MV88F6281GTW_GE_OE_VAL_LOW,
|
||||
MV88F6281GTW_GE_OE_VAL_HIGH,
|
||||
MV88F6281GTW_GE_OE_LOW, MV88F6281GTW_GE_OE_HIGH);
|
||||
|
||||
/* Multi-Purpose Pins Functionality configuration */
|
||||
static const u32 kwmpp_config[] = {
|
||||
MPP0_SPI_SCn,
|
||||
MPP1_SPI_MOSI,
|
||||
MPP2_SPI_SCK,
|
||||
MPP3_SPI_MISO,
|
||||
MPP4_GPIO,
|
||||
MPP5_GPO,
|
||||
MPP6_SYSRST_OUTn,
|
||||
MPP7_SPI_SCn,
|
||||
MPP8_TW_SDA,
|
||||
MPP9_TW_SCK,
|
||||
MPP10_UART0_TXD,
|
||||
MPP11_UART0_RXD,
|
||||
MPP12_GPO,
|
||||
MPP13_GPIO,
|
||||
MPP14_GPIO,
|
||||
MPP15_GPIO,
|
||||
MPP16_GPIO,
|
||||
MPP17_GPIO,
|
||||
MPP18_GPO,
|
||||
MPP19_GPO,
|
||||
MPP20_GPIO,
|
||||
MPP21_GPIO,
|
||||
MPP22_GPIO,
|
||||
MPP23_GPIO,
|
||||
MPP24_GPIO,
|
||||
MPP25_GPIO,
|
||||
MPP26_GPIO,
|
||||
MPP27_GPIO,
|
||||
MPP28_GPIO,
|
||||
MPP29_GPIO,
|
||||
MPP30_GPIO,
|
||||
MPP31_GPIO,
|
||||
MPP32_GPIO,
|
||||
MPP33_GPIO,
|
||||
MPP34_GPIO,
|
||||
MPP35_GPIO,
|
||||
MPP36_GPIO,
|
||||
MPP37_GPIO,
|
||||
MPP38_GPIO,
|
||||
MPP39_GPIO,
|
||||
MPP40_GPIO,
|
||||
MPP41_GPIO,
|
||||
MPP42_GPIO,
|
||||
MPP43_GPIO,
|
||||
MPP44_GPIO,
|
||||
MPP45_GPIO,
|
||||
MPP46_GPIO,
|
||||
MPP47_GPIO,
|
||||
MPP48_GPIO,
|
||||
MPP49_GPIO,
|
||||
0
|
||||
};
|
||||
kirkwood_mpp_conf(kwmpp_config, NULL);
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_init(void)
|
||||
{
|
||||
/*
|
||||
* arch number of board
|
||||
*/
|
||||
gd->bd->bi_arch_number = MACH_TYPE_MV88F6281GTW_GE;
|
||||
|
||||
/* adress of boot parameters */
|
||||
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_MV88E61XX_SWITCH
|
||||
void reset_phy(void)
|
||||
{
|
||||
/* configure and initialize switch */
|
||||
struct mv88e61xx_config swcfg = {
|
||||
.name = "egiga0",
|
||||
.vlancfg = MV88E61XX_VLANCFG_ROUTER,
|
||||
.rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
|
||||
.led_init = MV88E61XX_LED_INIT_EN,
|
||||
.mdip = MV88E61XX_MDIP_REVERSE,
|
||||
.portstate = MV88E61XX_PORTSTT_FORWARDING,
|
||||
.cpuport = (1 << 5),
|
||||
.ports_enabled = 0x3f
|
||||
};
|
||||
|
||||
mv88e61xx_switch_initialize(&swcfg);
|
||||
}
|
||||
#endif /* CONFIG_MV88E61XX_SWITCH */
|
||||
@ -1,20 +0,0 @@
|
||||
/*
|
||||
* (C) Copyright 2009
|
||||
* Marvell Semiconductor <www.marvell.com>
|
||||
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __MV88F6281GTW_GE_H
|
||||
#define __MV88F6281GTW_GE_H
|
||||
|
||||
#define MV88F6281GTW_GE_OE_LOW (~((1 << 7) | (1 << 12) \
|
||||
|(1 << 20) | (1 << 21))) /*enable GLED,RLED */
|
||||
#define MV88F6281GTW_GE_OE_HIGH (~((1 << 4)|(1 << 6)|(1 << 7)|(1 << 12) \
|
||||
|(1 << 13)|(1 << 16)|(1 << 17)))
|
||||
#define MV88F6281GTW_GE_OE_VAL_LOW (1 << 20) /*make GLED on */
|
||||
#define MV88F6281GTW_GE_OE_VAL_HIGH ((1 << 6)|(1 << 13)|(1 << 16)|(1 << 17))
|
||||
|
||||
|
||||
#endif /* __MV88F6281GTW_GE_H */
|
||||
@ -1,7 +0,0 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_KIRKWOOD=y
|
||||
CONFIG_TARGET_MV88F6281GTW_GE=y
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
# CONFIG_CMD_FLASH is not set
|
||||
# CONFIG_CMD_SETEXPR is not set
|
||||
CONFIG_SPI_FLASH=y
|
||||
@ -1,88 +0,0 @@
|
||||
/*
|
||||
* (C) Copyright 2009
|
||||
* Marvell Semiconductor <www.marvell.com>
|
||||
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef _CONFIG_MV88F6281GTW_GE_H
|
||||
#define _CONFIG_MV88F6281GTW_GE_H
|
||||
|
||||
/*
|
||||
* Version number information
|
||||
*/
|
||||
#define CONFIG_IDENT_STRING "\nMarvell-MV88F6281GTW_GE"
|
||||
|
||||
/*
|
||||
* High Level Configuration Options (easy to change)
|
||||
*/
|
||||
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
|
||||
#define CONFIG_KW88F6281 1 /* SOC Name */
|
||||
#define CONFIG_MACH_MV88F6281GTW_GE /* Machine type */
|
||||
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
|
||||
|
||||
/*
|
||||
* Commands configuration
|
||||
*/
|
||||
#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
|
||||
#define CONFIG_CMD_DHCP
|
||||
#define CONFIG_CMD_PING
|
||||
#define CONFIG_CMD_ENV
|
||||
#define CONFIG_CMD_FAT
|
||||
#define CONFIG_CMD_PING
|
||||
#define CONFIG_CMD_SF
|
||||
#define CONFIG_CMD_USB
|
||||
|
||||
/*
|
||||
* mv-common.h should be defined after CMD configs since it used them
|
||||
* to enable certain macros
|
||||
*/
|
||||
#include "mv-common.h"
|
||||
|
||||
/* Unwanted stuffs from mv-common.h */
|
||||
#undef CONFIG_CMD_EXT2
|
||||
#undef CONFIG_CMD_JFFS2
|
||||
#undef CONFIG_CMD_FAT
|
||||
#undef CONFIG_CMD_UBI
|
||||
#undef CONFIG_CMD_UBIFS
|
||||
#undef CONFIG_RBTREE
|
||||
|
||||
/*
|
||||
* Environment variables configurations
|
||||
*/
|
||||
#ifdef CONFIG_SPI_FLASH
|
||||
#define CONFIG_ENV_IS_IN_SPI_FLASH 1
|
||||
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K */
|
||||
#else
|
||||
#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
|
||||
#endif
|
||||
#define CONFIG_ENV_SIZE 0x1000 /* 4k */
|
||||
#define CONFIG_ENV_ADDR 0x30000
|
||||
#define CONFIG_ENV_OFFSET 0x30000 /* env starts here */
|
||||
|
||||
/*
|
||||
* Default environment variables
|
||||
*/
|
||||
#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
|
||||
"setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
|
||||
"${x_bootcmd_usb}; bootm 0x6400000;"
|
||||
|
||||
#define CONFIG_MTDPARTS "spi0.0:512k(uboot)," \
|
||||
"512k@512k(psm),2m@1m(kernel),13m@3m(rootfs)\0"
|
||||
|
||||
#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
|
||||
"=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
|
||||
"x_bootcmd_kernel=cp.b 0xE8100000 0x6400000 0x200000\0" \
|
||||
"x_bootcmd_usb=usb start\0" \
|
||||
"x_bootargs_root=root=/dev/mtdblock3 ro rootfstype=squashfs\0"
|
||||
|
||||
/*
|
||||
* Ethernet Driver configuration
|
||||
*/
|
||||
#ifdef CONFIG_CMD_NET
|
||||
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
|
||||
#define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */
|
||||
#endif /* CONFIG_CMD_NET */
|
||||
|
||||
#endif /* _CONFIG_MV88F6281GTW_GE_H */
|
||||
Loading…
Reference in New Issue
Block a user