ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage. HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K). A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Tested-by: Peter Robinson <pbrobinson@gmail.com>
This commit is contained in:
Tom Warren
parent
808e19362f
commit
7c02bc9649
@ -180,7 +180,8 @@ dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
|
||||
tegra210-e2220-1170.dtb \
|
||||
tegra210-p2371-0000.dtb \
|
||||
tegra210-p2371-2180.dtb \
|
||||
tegra210-p2571.dtb
|
||||
tegra210-p2571.dtb \
|
||||
tegra210-p3450-0000.dtb
|
||||
|
||||
dtb-$(CONFIG_ARCH_MVEBU) += \
|
||||
armada-3720-db.dtb \
|
||||
|
||||
147
arch/arm/dts/tegra210-p3450-0000.dts
Normal file
147
arch/arm/dts/tegra210-p3450-0000.dts
Normal file
@ -0,0 +1,147 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* (C) Copyright 2019-2020 NVIDIA Corporation <www.nvidia.com>
|
||||
*/
|
||||
/dts-v1/;
|
||||
|
||||
#include "tegra210.dtsi"
|
||||
|
||||
/ {
|
||||
model = "NVIDIA Jetson Nano Developer Kit";
|
||||
compatible = "nvidia,p3450-0000", "nvidia,tegra210";
|
||||
|
||||
chosen {
|
||||
stdout-path = &uarta;
|
||||
};
|
||||
|
||||
aliases {
|
||||
ethernet = "/pcie@1003000/pci@2,0/ethernet@0,0";
|
||||
i2c0 = "/i2c@7000d000";
|
||||
i2c2 = "/i2c@7000c400";
|
||||
i2c3 = "/i2c@7000c500";
|
||||
i2c4 = "/i2c@7000c700";
|
||||
mmc0 = "/sdhci@700b0600";
|
||||
mmc1 = "/sdhci@700b0000";
|
||||
spi0 = "/spi@70410000";
|
||||
usb0 = "/usb@7d000000";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0x0 0x80000000 0x0 0xc0000000>;
|
||||
};
|
||||
|
||||
pcie@1003000 {
|
||||
status = "okay";
|
||||
|
||||
pci@1,0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
pci@2,0 {
|
||||
status = "okay";
|
||||
|
||||
ethernet@0,0 {
|
||||
reg = <0x000000 0 0 0 0>;
|
||||
local-mac-address = [ 00 00 00 00 00 00 ];
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
serial@70006000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
padctl@7009f000 {
|
||||
pinctrl-0 = <&padctl_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
padctl_default: pinmux {
|
||||
xusb {
|
||||
nvidia,lanes = "otg-1", "otg-2";
|
||||
nvidia,function = "xusb";
|
||||
nvidia,iddq = <0>;
|
||||
};
|
||||
|
||||
usb3 {
|
||||
nvidia,lanes = "pcie-5", "pcie-6";
|
||||
nvidia,function = "usb3";
|
||||
nvidia,iddq = <0>;
|
||||
};
|
||||
|
||||
pcie-x1 {
|
||||
nvidia,lanes = "pcie-0";
|
||||
nvidia,function = "pcie-x1";
|
||||
nvidia,iddq = <0>;
|
||||
};
|
||||
|
||||
pcie-x4 {
|
||||
nvidia,lanes = "pcie-1", "pcie-2",
|
||||
"pcie-3", "pcie-4";
|
||||
nvidia,function = "pcie-x4";
|
||||
nvidia,iddq = <0>;
|
||||
};
|
||||
|
||||
sata {
|
||||
nvidia,lanes = "sata-0";
|
||||
nvidia,function = "sata";
|
||||
nvidia,iddq = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
sdhci@700b0000 {
|
||||
status = "okay";
|
||||
cd-gpios = <&gpio TEGRA_GPIO(Z, 1) GPIO_ACTIVE_LOW>;
|
||||
power-gpios = <&gpio TEGRA_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
|
||||
bus-width = <4>;
|
||||
};
|
||||
|
||||
sdhci@700b0600 {
|
||||
status = "okay";
|
||||
bus-width = <8>;
|
||||
non-removable;
|
||||
};
|
||||
|
||||
i2c@7000c400 {
|
||||
status = "okay";
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
i2c@7000c500 {
|
||||
status = "okay";
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
i2c@7000c700 {
|
||||
status = "okay";
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
i2c@7000d000 {
|
||||
status = "okay";
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
spi@70410000 {
|
||||
status = "okay";
|
||||
spi-max-frequency = <80000000>;
|
||||
};
|
||||
|
||||
usb@7d000000 {
|
||||
status = "okay";
|
||||
dr_mode = "peripheral";
|
||||
};
|
||||
|
||||
clocks {
|
||||
compatible = "simple-bus";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
clk32k_in: clock@0 {
|
||||
compatible = "fixed-clock";
|
||||
reg = <0>;
|
||||
#clock-cells = <0>;
|
||||
clock-frequency = <32768>;
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -217,6 +217,31 @@ int board_early_init_f(void)
|
||||
arch_timer_init();
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_DISABLE_SDMMC1_EARLY)
|
||||
/*
|
||||
* Turn off (reset/disable) SDMMC1 on Nano here, before GPIO INIT.
|
||||
* We do this because earlier bootloaders have enabled power to
|
||||
* SDMMC1 on Nano, and toggling power-gpio (PZ3) in pinmux_init()
|
||||
* results in power being back-driven into the SD-card and SDMMC1
|
||||
* HW, which is 'bad' as per the HW team.
|
||||
*
|
||||
* From the HW team: "LDO2 from the PMIC has already been set to 3.3v in
|
||||
* nvtboot/CBoot on Nano (for SD-card boot). So when U-Boot's GPIO_INIT
|
||||
* table sets PZ3 to OUT0 as per the pinmux spreadsheet, it turns off
|
||||
* the loadswitch. When PZ3 is 0 and not driving, essentially the SDCard
|
||||
* voltage turns off. Since the SDCard voltage is no longer there, the
|
||||
* SDMMC CLK/DAT lines are backdriving into what essentially is a
|
||||
* powered-off SDCard, that's why the voltage drops from 3.3V to ~1.6V"
|
||||
*
|
||||
* Note that this can probably be removed when we change over to storing
|
||||
* all BL components on QSPI on Nano, and U-Boot then becomes the first
|
||||
* one to turn on SDMMC1 power. Another fix would be to have CBoot
|
||||
* disable power/gate SDMMC1 off before handing off to U-Boot/kernel.
|
||||
*/
|
||||
reset_set_enable(PERIPH_ID_SDMMC1, 1);
|
||||
clock_set_enable(PERIPH_ID_SDMMC1, 0);
|
||||
#endif /* CONFIG_DISABLE_SDMMC1_EARLY */
|
||||
|
||||
pinmux_init();
|
||||
board_init_uart_f();
|
||||
|
||||
|
||||
@ -35,6 +35,12 @@ config TARGET_P2571
|
||||
help
|
||||
P2571 is a P2530 married to a P1963 I/O board
|
||||
|
||||
config TARGET_P3450_0000
|
||||
bool "NVIDIA Jetson Nano Developer Kit"
|
||||
select BOARD_LATE_INIT
|
||||
help
|
||||
P3450-0000 is a P3448 CPU board married to a P3449 I/O board.
|
||||
|
||||
endchoice
|
||||
|
||||
config SYS_SOC
|
||||
@ -44,5 +50,6 @@ source "board/nvidia/e2220-1170/Kconfig"
|
||||
source "board/nvidia/p2371-0000/Kconfig"
|
||||
source "board/nvidia/p2371-2180/Kconfig"
|
||||
source "board/nvidia/p2571/Kconfig"
|
||||
source "board/nvidia/p3450-0000/Kconfig"
|
||||
|
||||
endif
|
||||
|
||||
12
board/nvidia/p3450-0000/Kconfig
Normal file
12
board/nvidia/p3450-0000/Kconfig
Normal file
@ -0,0 +1,12 @@
|
||||
if TARGET_P3450_0000
|
||||
|
||||
config SYS_BOARD
|
||||
default "p3450-0000"
|
||||
|
||||
config SYS_VENDOR
|
||||
default "nvidia"
|
||||
|
||||
config SYS_CONFIG_NAME
|
||||
default "p3450-0000"
|
||||
|
||||
endif
|
||||
6
board/nvidia/p3450-0000/MAINTAINERS
Normal file
6
board/nvidia/p3450-0000/MAINTAINERS
Normal file
@ -0,0 +1,6 @@
|
||||
P3450-0000 BOARD
|
||||
M: Tom Warren <twarren@nvidia.com>
|
||||
S: Maintained
|
||||
F: board/nvidia/p3450-0000/
|
||||
F: include/configs/p3450-0000.h
|
||||
F: configs/p3450-0000_defconfig
|
||||
8
board/nvidia/p3450-0000/Makefile
Normal file
8
board/nvidia/p3450-0000/Makefile
Normal file
@ -0,0 +1,8 @@
|
||||
#
|
||||
# (C) Copyright 2018
|
||||
# NVIDIA Corporation <www.nvidia.com>
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
|
||||
obj-y += p3450-0000.o
|
||||
178
board/nvidia/p3450-0000/p3450-0000.c
Normal file
178
board/nvidia/p3450-0000/p3450-0000.c
Normal file
@ -0,0 +1,178 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* (C) Copyright 2018-2019
|
||||
* NVIDIA Corporation <www.nvidia.com>
|
||||
*
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <fdtdec.h>
|
||||
#include <i2c.h>
|
||||
#include <linux/libfdt.h>
|
||||
#include <pca953x.h>
|
||||
#include <asm/arch-tegra/cboot.h>
|
||||
#include <asm/arch/gpio.h>
|
||||
#include <asm/arch/pinmux.h>
|
||||
#include "../p2571/max77620_init.h"
|
||||
|
||||
void pin_mux_mmc(void)
|
||||
{
|
||||
struct udevice *dev;
|
||||
uchar val;
|
||||
int ret;
|
||||
|
||||
/* Turn on MAX77620 LDO2 to 3.3V for SD card power */
|
||||
debug("%s: Set LDO2 for VDDIO_SDMMC_AP power to 3.3V\n", __func__);
|
||||
ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
|
||||
if (ret) {
|
||||
printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
|
||||
return;
|
||||
}
|
||||
/* 0xF2 for 3.3v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
|
||||
val = 0xF2;
|
||||
ret = dm_i2c_write(dev, MAX77620_CNFG1_L2_REG, &val, 1);
|
||||
if (ret)
|
||||
printf("i2c_write 0 0x3c 0x27 failed: %d\n", ret);
|
||||
|
||||
/* Disable LDO4 discharge */
|
||||
ret = dm_i2c_read(dev, MAX77620_CNFG2_L4_REG, &val, 1);
|
||||
if (ret) {
|
||||
printf("i2c_read 0 0x3c 0x2c failed: %d\n", ret);
|
||||
} else {
|
||||
val &= ~BIT(1); /* ADE */
|
||||
ret = dm_i2c_write(dev, MAX77620_CNFG2_L4_REG, &val, 1);
|
||||
if (ret)
|
||||
printf("i2c_write 0 0x3c 0x2c failed: %d\n", ret);
|
||||
}
|
||||
|
||||
/* Set MBLPD */
|
||||
ret = dm_i2c_read(dev, MAX77620_CNFGGLBL1_REG, &val, 1);
|
||||
if (ret) {
|
||||
printf("i2c_write 0 0x3c 0x00 failed: %d\n", ret);
|
||||
} else {
|
||||
val |= BIT(6); /* MBLPD */
|
||||
ret = dm_i2c_write(dev, MAX77620_CNFGGLBL1_REG, &val, 1);
|
||||
if (ret)
|
||||
printf("i2c_write 0 0x3c 0x00 failed: %d\n", ret);
|
||||
}
|
||||
}
|
||||
|
||||
#ifdef CONFIG_PCI_TEGRA
|
||||
int tegra_pcie_board_init(void)
|
||||
{
|
||||
struct udevice *dev;
|
||||
uchar val;
|
||||
int ret;
|
||||
|
||||
/* Turn on MAX77620 LDO1 to 1.05V for PEX power */
|
||||
debug("%s: Set LDO1 for PEX power to 1.05V\n", __func__);
|
||||
ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
|
||||
if (ret) {
|
||||
printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
|
||||
return -1;
|
||||
}
|
||||
/* 0xCA for 1.05v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
|
||||
val = 0xCA;
|
||||
ret = dm_i2c_write(dev, MAX77620_CNFG1_L1_REG, &val, 1);
|
||||
if (ret)
|
||||
printf("i2c_write 0 0x3c 0x25 failed: %d\n", ret);
|
||||
|
||||
return 0;
|
||||
}
|
||||
#endif /* PCI */
|
||||
|
||||
static void ft_mac_address_setup(void *fdt)
|
||||
{
|
||||
const void *cboot_fdt = (const void *)cboot_boot_x0;
|
||||
uint8_t mac[ETH_ALEN], local_mac[ETH_ALEN];
|
||||
const char *path;
|
||||
int offset, err;
|
||||
|
||||
err = cboot_get_ethaddr(cboot_fdt, local_mac);
|
||||
if (err < 0)
|
||||
memset(local_mac, 0, ETH_ALEN);
|
||||
|
||||
path = fdt_get_alias(fdt, "ethernet");
|
||||
if (!path)
|
||||
return;
|
||||
|
||||
debug("ethernet alias found: %s\n", path);
|
||||
|
||||
offset = fdt_path_offset(fdt, path);
|
||||
if (offset < 0) {
|
||||
printf("ethernet alias points to absent node %s\n", path);
|
||||
return;
|
||||
}
|
||||
|
||||
if (is_valid_ethaddr(local_mac)) {
|
||||
err = fdt_setprop(fdt, offset, "local-mac-address", local_mac,
|
||||
ETH_ALEN);
|
||||
if (!err)
|
||||
debug("Local MAC address set: %pM\n", local_mac);
|
||||
}
|
||||
|
||||
if (eth_env_get_enetaddr("ethaddr", mac)) {
|
||||
if (memcmp(local_mac, mac, ETH_ALEN) != 0) {
|
||||
err = fdt_setprop(fdt, offset, "mac-address", mac,
|
||||
ETH_ALEN);
|
||||
if (!err)
|
||||
debug("MAC address set: %pM\n", mac);
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
static int ft_copy_carveout(void *dst, const void *src, const char *node)
|
||||
{
|
||||
struct fdt_memory fb;
|
||||
int err;
|
||||
|
||||
err = fdtdec_get_carveout(src, node, "memory-region", 0, &fb);
|
||||
if (err < 0) {
|
||||
if (err != -FDT_ERR_NOTFOUND)
|
||||
printf("failed to get carveout for %s: %d\n", node,
|
||||
err);
|
||||
|
||||
return err;
|
||||
}
|
||||
|
||||
err = fdtdec_set_carveout(dst, node, "memory-region", 0, "framebuffer",
|
||||
&fb);
|
||||
if (err < 0) {
|
||||
printf("failed to set carveout for %s: %d\n", node, err);
|
||||
return err;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void ft_carveout_setup(void *fdt)
|
||||
{
|
||||
const void *cboot_fdt = (const void *)cboot_boot_x0;
|
||||
static const char * const nodes[] = {
|
||||
"/host1x@50000000/dc@54200000",
|
||||
"/host1x@50000000/dc@54240000",
|
||||
};
|
||||
unsigned int i;
|
||||
int err;
|
||||
|
||||
for (i = 0; i < ARRAY_SIZE(nodes); i++) {
|
||||
printf("copying carveout for %s...\n", nodes[i]);
|
||||
|
||||
err = ft_copy_carveout(fdt, cboot_fdt, nodes[i]);
|
||||
if (err < 0) {
|
||||
if (err != -FDT_ERR_NOTFOUND)
|
||||
printf("failed to copy carveout for %s: %d\n",
|
||||
nodes[i], err);
|
||||
|
||||
continue;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
int ft_board_setup(void *fdt, bd_t *bd)
|
||||
{
|
||||
ft_mac_address_setup(fdt);
|
||||
ft_carveout_setup(fdt);
|
||||
|
||||
return 0;
|
||||
}
|
||||
64
configs/p3450-0000_defconfig
Normal file
64
configs/p3450-0000_defconfig
Normal file
@ -0,0 +1,64 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_TEGRA=y
|
||||
CONFIG_SYS_TEXT_BASE=0x80080000
|
||||
CONFIG_TEGRA210=y
|
||||
CONFIG_TARGET_P3450_0000=y
|
||||
CONFIG_NR_DRAM_BANKS=2
|
||||
CONFIG_OF_SYSTEM_SETUP=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_CONSOLE_MUX=y
|
||||
CONFIG_SYS_STDIO_DEREGISTER=y
|
||||
CONFIG_SYS_PROMPT="Tegra210 (P3450-0000) # "
|
||||
# CONFIG_CMD_IMI is not set
|
||||
CONFIG_CMD_DFU=y
|
||||
# CONFIG_CMD_FLASH is not set
|
||||
CONFIG_CMD_GPIO=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_PCI=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_SPI=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_USB_MASS_STORAGE=y
|
||||
# CONFIG_CMD_SETEXPR is not set
|
||||
# CONFIG_CMD_NFS is not set
|
||||
CONFIG_CMD_EXT4_WRITE=y
|
||||
CONFIG_OF_LIVE=y
|
||||
CONFIG_DEFAULT_DEVICE_TREE="tegra210-p3450-0000"
|
||||
CONFIG_DFU_MMC=y
|
||||
CONFIG_DFU_RAM=y
|
||||
CONFIG_DFU_SF=y
|
||||
CONFIG_SYS_I2C_TEGRA=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SPI_FLASH_MACRONIX=y
|
||||
CONFIG_SPI_FLASH_USE_4K_SECTORS=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=24000000
|
||||
CONFIG_RTL8169=y
|
||||
CONFIG_PCI=y
|
||||
CONFIG_DM_PCI=y
|
||||
CONFIG_DM_PCI_COMPAT=y
|
||||
CONFIG_PCI_TEGRA=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_TEGRA114_SPI=y
|
||||
CONFIG_TEGRA210_QSPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_DM_USB=y
|
||||
CONFIG_USB_EHCI_HCD=y
|
||||
CONFIG_USB_EHCI_TEGRA=y
|
||||
CONFIG_USB_GADGET=y
|
||||
CONFIG_USB_GADGET_MANUFACTURER="NVIDIA"
|
||||
CONFIG_USB_GADGET_VENDOR_NUM=0x0955
|
||||
CONFIG_USB_GADGET_PRODUCT_NUM=0x701a
|
||||
CONFIG_CI_UDC=y
|
||||
CONFIG_USB_GADGET_DOWNLOAD=y
|
||||
CONFIG_USB_HOST_ETHER=y
|
||||
CONFIG_USB_ETHER_ASIX=y
|
||||
# CONFIG_ENV_IS_IN_MMC is not set
|
||||
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_ENV_SECT_SIZE=0x1000
|
||||
CONFIG_ENV_OFFSET=0xFFFFE000
|
||||
CONFIG_BOOTP_PREFER_SERVERIP=y
|
||||
CONFIG_POSITION_INDEPENDENT=y
|
||||
CONFIG_DISABLE_SDMMC1_EARLY=y
|
||||
46
include/configs/p3450-0000.h
Normal file
46
include/configs/p3450-0000.h
Normal file
@ -0,0 +1,46 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* (C) Copyright 2018-2019 NVIDIA Corporation.
|
||||
*/
|
||||
|
||||
#ifndef _P3450_0000_H
|
||||
#define _P3450_0000_H
|
||||
|
||||
#include <linux/sizes.h>
|
||||
|
||||
#include "tegra210-common.h"
|
||||
|
||||
/* High-level configuration options */
|
||||
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA P3450-0000"
|
||||
|
||||
/* Board-specific serial config */
|
||||
#define CONFIG_TEGRA_ENABLE_UARTA
|
||||
|
||||
/* Only MMC/PXE/DHCP for now, add USB back in later when supported */
|
||||
#define BOOT_TARGET_DEVICES(func) \
|
||||
func(MMC, mmc, 1) \
|
||||
func(MMC, mmc, 0) \
|
||||
func(PXE, pxe, na) \
|
||||
func(DHCP, dhcp, na)
|
||||
|
||||
/* Environment at end of QSPI, in the VER partition */
|
||||
#define CONFIG_ENV_SPI_MAX_HZ 48000000
|
||||
#define CONFIG_ENV_SPI_MODE SPI_MODE_0
|
||||
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
|
||||
|
||||
#define CONFIG_PREBOOT
|
||||
|
||||
#define BOARD_EXTRA_ENV_SETTINGS \
|
||||
"preboot=if test -e mmc 1:1 /u-boot-preboot.scr; then " \
|
||||
"load mmc 1:1 ${scriptaddr} /u-boot-preboot.scr; " \
|
||||
"source ${scriptaddr}; " \
|
||||
"fi\0"
|
||||
|
||||
/* General networking support */
|
||||
#include "tegra-common-usb-gadget.h"
|
||||
#include "tegra-common-post.h"
|
||||
|
||||
/* Crystal is 38.4MHz. clk_m runs at half that rate */
|
||||
#define COUNTER_FREQUENCY 19200000
|
||||
|
||||
#endif /* _P3450_0000_H */
|
||||
Loading…
Reference in New Issue
Block a user