* Patch by Martin Krause, 17 Jul 2003:

add delay to get I2C working with "imm" command and s3c24x0_i2c.c

* Patch by Richard Woodruff, 17 July 03:
  - Fixed bug in OMAP1510 baud rate divisor settings.

* Patch by Nye Liu, 16 July 2003:
  MPC860FADS fixes:
  - add MPC86xADS support (uses MPC86xADS.h)
  - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
    o PLPRCR changes
    o BRG changes (EXTAL/XTAL restricted to 10MHz)
    o don't trust gclk() software measurement by default, depend on
      CONFIG_8xx_GCLK_FREQ
  - add DRAM SIMM not installed detection
  - use more "correct" SDRAM initialization sequence
  - allow different SDRAM sizes (8xxADS has 8M)
  - default DER is 0
  - remove unused MAMR defines from FADS860T.h (all done in fads.c)
  - rename MAMR/MBMR defines to be more consistent. Should eventually
    be merged into MxMR to better reflect the PowerQUICC datasheet.

* Patch by Yuli Barcohen, 16 Jul 2003:
  support new Motorola PQ2FADS-ZU evaluation board which replaced
  MPC8260ADS and MPC8266ADS

cpu/mpc8xx/cpu.c

@@ -42,12 +42,23 @@
 static char *cpu_warning = "\n         " \
 	"*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***";
 
-#if ((defined(CONFIG_MPC860) || defined(CONFIG_MPC855)) && \
+#if ((defined(CONFIG_MPC86x) || defined(CONFIG_MPC855)) && \
      !defined(CONFIG_MPC862))
-# ifdef CONFIG_MPC855
+
+# if defined(CONFIG_MPC855)
 #  define	ID_STR	"PC855"
+# elif defined(CONFIG_MPC852T)
+#  define	ID_STR	"PC852T"
+# elif defined(CONFIG_MPC859T)
+#  define	ID_STR	"PC859T"
+# elif defined(CONFIG_MPC859DSL)
+#  define	ID_STR	"PC859DSL"
+# elif defined(CONFIG_MPC860P)
+#  define	ID_STR	"PC860P"
+# elif defined(CONFIG_MPC866T)
+#  define	ID_STR	"PC866T"
 # else
-#  define	ID_STR	"PC860"
+#  define	ID_STR	"PC86x"	/* unknown 86x chip */
 # endif
 
 static int check_CPU (long clock, uint pvr, uint immr)
@@ -68,6 +79,10 @@ static int check_CPU (long clock, uint pvr, uint immr)
 	m = 0;
 
 	switch (k) {
+#ifdef CONFIG_MPC866_et_al
+                /* MPC866P/MPC866T/MPC859T/MPC859DSL/MPC852T */
+	case 0x08000003: pre = 'M'; suf = ""; m = 1; break;
+#else
 	case 0x00020001: pre = 'p'; suf = ""; break;
 	case 0x00030001: suf = ""; break;
 	case 0x00120003: suf = "A"; break;
@@ -76,17 +91,16 @@ static int check_CPU (long clock, uint pvr, uint immr)
 	case 0x00200004: suf = "B"; break;
 
 	case 0x00300004: suf = "C"; break;
-	case 0x00310004: suf = "C1"; m = 1;
-		break;
+	case 0x00310004: suf = "C1"; m = 1; break;
 
 	case 0x00200064: mid = "SR"; suf = "B"; break;
 	case 0x00300065: mid = "SR"; suf = "C"; break;
 	case 0x00310065: mid = "SR"; suf = "C1"; m = 1; break;
 	case 0x05010000: suf = "D3"; m = 1; break;
 	case 0x05020000: suf = "D4"; m = 1; break;
-
 		/* this value is not documented anywhere */
 	case 0x40000000: pre = 'P'; suf = "D"; m = 1; break;
+#endif
 
 	default: suf = NULL; break;
 	}
@@ -101,7 +115,7 @@ static int check_CPU (long clock, uint pvr, uint immr)
 	printf (" %u kB I-Cache", checkicache () >> 10);
 	printf (" %u kB D-Cache", checkdcache () >> 10);
 
-	/* lets check and see if we're running on a 860T (or P?) */
+	/* do we have a FEC (860T/P or 852/859/866)? */
 
 	immap->im_cpm.cp_fec.fec_addr_low = 0x12345678;
 	if (immap->im_cpm.cp_fec.fec_addr_low == 0x12345678) {
@@ -114,6 +128,12 @@ static int check_CPU (long clock, uint pvr, uint immr)
 
 	putc ('\n');
 
+#ifdef DEBUG
+        if(clock != measure_gclk()) {
+            printf ("clock %ldHz != %dHz\n", clock, measure_gclk());
+        }
+#endif
+
 	return 0;
 }
 
@@ -316,7 +336,7 @@ int checkicache (void)
 	volatile memctl8xx_t *memctl = &immap->im_memctl;
 	u32 cacheon = rd_ic_cst () & IDC_ENABLED;
 
-#ifdef CONFIG_IP860
+#ifdef CONFIG_IP86x
 	u32 k = memctl->memc_br1 & ~0x00007fff;	/* probe in flash memoryarea */
 #else
 	u32 k = memctl->memc_br0 & ~0x00007fff;	/* probe in flash memoryarea */
@@ -363,7 +383,7 @@ int checkdcache (void)
 	volatile memctl8xx_t *memctl = &immap->im_memctl;
 	u32 cacheon = rd_dc_cst () & IDC_ENABLED;
 
-#ifdef CONFIG_IP860
+#ifdef CONFIG_IP86x
 	u32 k = memctl->memc_br1 & ~0x00007fff;	/* probe in flash memoryarea */
 #else
 	u32 k = memctl->memc_br0 & ~0x00007fff;	/* probe in flash memoryarea */
@@ -462,8 +482,20 @@ unsigned long get_tbclk (void)
 	if (immr->im_clkrst.car_sccr & SCCR_TBS) {
 		return (gd->cpu_clk / 16);
 	}
+#define PLPRCR_val(a) (((CFG_PLPRCR) & PLPRCR_ ## a ## _MSK) >> PLPRCR_ ## a ## _SHIFT)
+#ifdef CONFIG_MPC866_et_al
+        /*                   MFN
+                     MFI + -------
+                           MFD + 1
+          factor =  -----------------
+                     (PDF + 1) * 2^S
+         */
 
-	factor = (((CFG_PLPRCR) & PLPRCR_MF_MSK) >> PLPRCR_MF_SHIFT) + 1;
+	factor = (PLPRCR_val(MFI) + PLPRCR_val(MFN)/(PLPRCR_val(MFD)+1))/
+                 (PLPRCR_val(PDF)+1) / (1<<PLPRCR_val(S));
+#else
+	factor = PLPRCR_val(MF)+1;
+#endif
 
 	oscclk = gd->cpu_clk / factor;
 

cpu/mpc8xx/cpu_init.c

@@ -145,6 +145,7 @@ void cpu_init_f (volatile immap_t * immr)
     defined(CONFIG_RPXCLASSIC)	|| \
     defined(CONFIG_RPXLITE)	|| \
     defined(CONFIG_SPD823TS)	|| \
+    defined(CONFIG_MPC86xADS)	|| \
    (defined(CONFIG_MPC860T) && defined(CONFIG_FADS))
 
 	memctl->memc_br0 = CFG_BR0_PRELIM;

cpu/mpc8xx/fec.c

@@ -217,7 +217,8 @@ static int fec_init(struct eth_device* dev, bd_t * bd)
 	volatile immap_t *immr = (immap_t *) CFG_IMMR;
 	volatile fec_t *fecp = &(immr->im_cpm.cp_fec);
 
-#if defined(CONFIG_FADS) && defined(CONFIG_MPC860T)
+#if defined(CONFIG_FADS) && \
+	( defined(CONFIG_MPC860T) || defined(CONFIG_MPC866_et_al) )
 	/* configure FADS for fast (FEC) ethernet, half-duplex */
 	/* The LXT970 needs about 50ms to recover from reset, so
 	 * wait for it by discovering the PHY before leaving eth_init().

cpu/mpc8xx/interrupts.c

@@ -334,7 +334,11 @@ void timer_interrupt (struct pt_regs *regs)
 	/* Reset Timer Expired and Timers Interrupt Status */
 	immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
 	__asm__ ("nop");
+#ifdef CONFIG_MPC866_et_al
+	immr->im_clkrst.car_plprcr |= PLPRCR_TEXPS;
+#else
 	immr->im_clkrst.car_plprcr |= PLPRCR_TEXPS | PLPRCR_TMIST;
+#endif
 	/* Restore Decrementer Count */
 	set_dec (decrementer_count);
 

cpu/mpc8xx/scc.c

@@ -192,9 +192,9 @@ static int scc_init(struct eth_device* dev, bd_t *bis)
 
     volatile immap_t *immr = (immap_t *)CFG_IMMR;
 
-#if defined(CONFIG_FADS)
-#if defined(CONFIG_MPC860T)
-    /* The FADS860T doesn't use the MODEM_EN or DATA_VOICE signals.	*/
+#ifdef CONFIG_FADS
+#if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC860T)
+    /* The MPC86xADS/FADS860T don't use the MODEM_EN or DATA_VOICE signals. */
     *((uint *) BCSR4) &= ~BCSR4_ETHLOOP;
     *((uint *) BCSR4) |= BCSR4_TFPLDL|BCSR4_TPSQEL;
     *((uint *) BCSR1) &= ~BCSR1_ETHEN;

cpu/mpc8xx/serial.c

@@ -68,6 +68,23 @@
 #error "console not correctly defined"
 #endif
 
+static void serial_setdivisor(volatile cpm8xx_t *cp)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	int divisor=gd->cpu_clk/16/gd->baudrate;
+
+	if(divisor/16>0x1000) {
+		/* bad divisor, assume 50Mhz clock and 9600 baud */
+		divisor=(50*1000*1000)/16/9600;
+	}
+
+	if(divisor<=0x1000) {
+		cp->cp_brgc1=((divisor-1)<<1) | CPM_BRG_EN;
+	} else {
+		cp->cp_brgc1=((divisor/16-1)<<1) | CPM_BRG_EN | CPM_BRG_DIV16;
+	}
+}
+
 #if (defined (CONFIG_8xx_CONS_SMC1) || defined (CONFIG_8xx_CONS_SMC2))
 
 /*
@@ -229,8 +246,6 @@ int serial_init (void)
 void
 serial_setbrg (void)
 {
-	DECLARE_GLOBAL_DATA_PTR;
-
 	volatile immap_t *im = (immap_t *)CFG_IMMR;
 	volatile cpm8xx_t *cp = &(im->im_cpm);
 
@@ -242,8 +257,7 @@ serial_setbrg (void)
 
 	cp->cp_simode = 0x00000000;
 
-	cp->cp_brgc1 =
-		(((gd->cpu_clk / 16 / gd->baudrate)-1) << 1) | CPM_BRG_EN;
+	serial_setdivisor(cp);
 }
 
 #ifdef CONFIG_MODEM_SUPPORT
@@ -506,8 +520,6 @@ int serial_init (void)
 void
 serial_setbrg (void)
 {
-	DECLARE_GLOBAL_DATA_PTR;
-
 	volatile immap_t *im = (immap_t *)CFG_IMMR;
 	volatile cpm8xx_t *cp = &(im->im_cpm);
 
@@ -518,10 +530,8 @@ serial_setbrg (void)
 	 */
 
 	cp->cp_sicr &= ~(0x000000FF << (8 * SCC_INDEX));
-	/* no |= needed, since BRG1 is 000 */
 
-	cp->cp_brgc1 =
-		(((gd->cpu_clk / 16 / gd->baudrate)-1) << 1) | CPM_BRG_EN;
+	serial_setdivisor(cp);
 }
 
 void

cpu/mpc8xx/speed.c

@@ -32,7 +32,6 @@
 #define SPEED_PITC	 ((SPEED_PIT_COUNTS - 1) << PITC_SHIFT)
 #define SPEED_PITC_INIT	 ((SPEED_PIT_COUNTS + 1) << PITC_SHIFT)
 
-#if !defined(CONFIG_8xx_GCLK_FREQ)
 /* Access functions for the Machine State Register */
 static __inline__ unsigned long get_msr(void)
 {
@@ -46,7 +45,6 @@ static __inline__ void set_msr(unsigned long msr)
 {
 	asm volatile("mtmsr %0" : : "r" (msr));
 }
-#endif
 
 /* ------------------------------------------------------------------------- */
 
@@ -83,16 +81,20 @@ static __inline__ void set_msr(unsigned long msr)
  * CPU clock that is an even multiple of 0.1 MHz.
  */
 
-int get_clocks (void)
+unsigned long measure_gclk(void)
 {
-	DECLARE_GLOBAL_DATA_PTR;
-
 	volatile immap_t *immr = (immap_t *) CFG_IMMR;
-#ifndef	CONFIG_8xx_GCLK_FREQ
 	volatile cpmtimer8xx_t *timerp = &immr->im_cpmtimer;
 	ulong timer2_val;
 	ulong msr_val;
 
+#ifdef CONFIG_MPC866_et_al
+        /* dont use OSCM, only use EXTCLK/512 */
+        immr->im_clkrst.car_sccr |= SCCR_RTSEL | SCCR_RTDIV;
+#else
+        immr->im_clkrst.car_sccr &= ~(SCCR_RTSEL | SCCR_RTDIV);
+#endif
+
 	/* Reset + Stop Timer 2, no cascading
 	 */
 	timerp->cpmt_tgcr &= ~(TGCR_CAS2 | TGCR_RST2);
@@ -158,10 +160,27 @@ int get_clocks (void)
 	timerp->cpmt_tgcr &= ~(TGCR_RST2 | TGCR_FRZ2 | TGCR_STP2);
 	immr->im_sit.sit_piscr &= ~PISCR_PTE;
 
-	gd->cpu_clk = ((timer2_val + 2) / 4) * 100000L;	/* convert to Hz    */
+#ifdef CONFIG_MPC866_et_al
+        /* not using OSCM, using XIN, so scale appropriately */
+	return (((timer2_val + 2) / 4) * (CFG_8XX_XIN/512))/8192 * 100000L;
+#else
+	return ((timer2_val + 2) / 4) * 100000L;	/* convert to Hz    */
+#endif
+}
 
+/*
+ * get_clocks() fills in gd->cpu_clock depending on CONFIG_8xx_GCLK_FREQ
+ * or (if it is not defined) measure_gclk() (which uses the ref clock)
+ * from above.
+ */
+int get_clocks (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+#ifndef	CONFIG_8xx_GCLK_FREQ
+	gd->cpu_clk = measure_gclk();
 #else /* CONFIG_8xx_GCLK_FREQ */
-
 	/*
 	 * If for some reason measuring the gclk frequency won't
 	 * work, we return the hardwired value.