diff --git a/arch/arm/dts/kirkwood-6192.dtsi b/arch/arm/dts/kirkwood-6192.dtsi
new file mode 100644
index 0000000000..396bcba08a
--- /dev/null
+++ b/arch/arm/dts/kirkwood-6192.dtsi
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ mbus@f1000000 {
+ pciec: pcie@82000000 {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
+
+ pcie0: pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 9>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ compatible = "marvell,88f6192-pinctrl";
+
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp5", "mpp21", "mpp23";
+ marvell,function = "sata0";
+ };
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp4", "mpp20", "mpp22";
+ marvell,function = "sata1";
+ };
+ pmx_sdio: pmx-sdio {
+ marvell,pins = "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "sdio";
+ };
+ };
+
+ rtc: rtc@10300 {
+ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <53>;
+ clocks = <&gate_clk 7>;
+ };
+
+ sata: sata@80000 {
+ compatible = "marvell,orion-sata";
+ reg = <0x80000 0x5000>;
+ interrupts = <21>;
+ clocks = <&gate_clk 14>, <&gate_clk 15>;
+ clock-names = "0", "1";
+ phys = <&sata_phy0>, <&sata_phy1>;
+ phy-names = "port0", "port1";
+ status = "disabled";
+ };
+
+ sdio: mvsdio@90000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0x90000 0x200>;
+ interrupts = <28>;
+ clocks = <&gate_clk 4>;
+ bus-width = <4>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/kirkwood-6281.dtsi b/arch/arm/dts/kirkwood-6281.dtsi
new file mode 100644
index 0000000000..faa05849a4
--- /dev/null
+++ b/arch/arm/dts/kirkwood-6281.dtsi
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ mbus@f1000000 {
+ pciec: pcie@82000000 {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
+
+ pcie0: pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 9>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ compatible = "marvell,88f6281-pinctrl";
+
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp5", "mpp21", "mpp23";
+ marvell,function = "sata0";
+ };
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp4", "mpp20", "mpp22";
+ marvell,function = "sata1";
+ };
+ pmx_sdio: pmx-sdio {
+ marvell,pins = "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "sdio";
+ };
+ };
+
+ rtc: rtc@10300 {
+ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <53>;
+ clocks = <&gate_clk 7>;
+ };
+
+ sata: sata@80000 {
+ compatible = "marvell,orion-sata";
+ reg = <0x80000 0x5000>;
+ interrupts = <21>;
+ clocks = <&gate_clk 14>, <&gate_clk 15>;
+ clock-names = "0", "1";
+ phys = <&sata_phy0>, <&sata_phy1>;
+ phy-names = "port0", "port1";
+ status = "disabled";
+ };
+
+ sdio: mvsdio@90000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0x90000 0x200>;
+ interrupts = <28>;
+ clocks = <&gate_clk 4>;
+ pinctrl-0 = <&pmx_sdio>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/kirkwood-98dx4122.dtsi b/arch/arm/dts/kirkwood-98dx4122.dtsi
new file mode 100644
index 0000000000..299c147298
--- /dev/null
+++ b/arch/arm/dts/kirkwood-98dx4122.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ mbus@f1000000 {
+ pciec: pcie@82000000 {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
+
+ pcie0: pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 9>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ compatible = "marvell,98dx4122-pinctrl";
+
+ };
+ };
+};
+
+&sata_phy0 {
+ status = "disabled";
+};
+
+&sata_phy1 {
+ status = "disabled";
+};
diff --git a/arch/arm/dts/kirkwood-blackarmor-nas220.dts b/arch/arm/dts/kirkwood-blackarmor-nas220.dts
new file mode 100644
index 0000000000..07fbfca444
--- /dev/null
+++ b/arch/arm/dts/kirkwood-blackarmor-nas220.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for Seagate Blackarmor NAS220
+ *
+ * Copyright (C) 2014 Evgeni Dobrev <evgeni@studio-punkt.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+ model = "Seagate Blackarmor NAS220";
+ compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192",
+ "marvell,kirkwood";
+
+ memory { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ button {
+ label = "Power";
+ linux,code = <KEY_SLEEP>;
+ gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ blue-power {
+ label = "nas220:blue:power";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
+ pinctrl-names = "default";
+
+ sata0_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ };
+
+ sata1_power: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 28 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+/*
+ * Serial port routed to connector CN5
+ *
+ * pin 1 - TX (CPU's TX)
+ * pin 4 - RX (CPU's RX)
+ * pin 6 - GND
+ */
+&uart0 {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-0 = <&pmx_button_reset &pmx_button_power>;
+ pinctrl-names = "default";
+
+ pmx_act_sata0: pmx-act-sata0 {
+ marvell,pins = "mpp15";
+ marvell,function = "sata0";
+ };
+
+ pmx_act_sata1: pmx-act-sata1 {
+ marvell,pins = "mpp16";
+ marvell,function = "sata1";
+ };
+
+ pmx_power_sata0: pmx-power-sata0 {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_sata1: pmx-power-sata1 {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_button_power: pmx-button-power {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+};
+
+&sata {
+ status = "okay";
+ nr-ports = <2>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ adt7476: thermal@2e {
+ compatible = "adi,adt7476";
+ reg = <0x2e>;
+ };
+};
+
+&nand {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@8 {
+ reg = <8>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-dns325.dts b/arch/arm/dts/kirkwood-dns325.dts
new file mode 100644
index 0000000000..94d9c06cbb
--- /dev/null
+++ b/arch/arm/dts/kirkwood-dns325.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood-dnskw.dtsi"
+
+/ {
+ model = "D-Link DNS-325 NAS (Rev A1)";
+ compatible = "dlink,dns-325-a1", "dlink,dns-325", "dlink,dns-kirkwood", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_power &pmx_led_red_usb_325
+ &pmx_led_red_left_hdd &pmx_led_red_right_hdd
+ &pmx_led_white_usb>;
+ pinctrl-names = "default";
+
+ white-power {
+ label = "dns325:white:power";
+ gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ white-usb {
+ label = "dns325:white:usb";
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* GPIO 43 */
+ };
+ red-l_hdd {
+ label = "dns325:red:l_hdd";
+ gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+ };
+ red-r_hdd {
+ label = "dns325:red:r_hdd";
+ gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+ };
+ red-usb {
+ label = "dns325:red:usb";
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ ocp@f1000000 {
+ i2c@11000 {
+ status = "okay";
+
+ lm75: lm75@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+ };
+ serial@12000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/arch/arm/dts/kirkwood-dnskw.dtsi b/arch/arm/dts/kirkwood-dnskw.dtsi
new file mode 100644
index 0000000000..cbaf06f2f7
--- /dev/null
+++ b/arch/arm/dts/kirkwood-dnskw.dtsi
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "D-Link DNS NASes (kirkwood-based)";
+ compatible = "dlink,dns-kirkwood", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_button_power &pmx_button_unmount
+ &pmx_button_reset>;
+ pinctrl-names = "default";
+
+ power {
+ label = "Power button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ };
+ eject {
+ label = "USB unmount button";
+ linux,code = <KEY_EJECTCD>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_fan {
+ /* Fan: ADDA AD045HB-G73 40mm 6000rpm@5v */
+ compatible = "gpio-fan";
+ pinctrl-0 = <&pmx_fan_high_speed &pmx_fan_low_speed>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW
+ &gpio1 13 GPIO_ACTIVE_LOW>;
+ gpio-fan,speed-map = <0 0
+ 3000 1
+ 6000 2>;
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_power_off>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+
+ pinctrl-0 = <&pmx_power_back_on &pmx_present_sata0
+ &pmx_present_sata1 &pmx_fan_tacho
+ &pmx_temp_alarm>;
+ pinctrl-names = "default";
+
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp20";
+ marvell,function = "sata1";
+ };
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp21";
+ marvell,function = "sata0";
+ };
+ pmx_led_power: pmx-led-power {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+ pmx_led_red_right_hdd: pmx-led-red-right-hdd {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+ pmx_led_red_left_hdd: pmx-led-red-left-hdd {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+ pmx_led_red_usb_325: pmx-led-red-usb-325 {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_button_power: pmx-button-power {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+ pmx_led_red_usb_320: pmx-led-red-usb-320 {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+ pmx_power_off: pmx-power-off {
+ marvell,pins = "mpp36";
+ marvell,function = "gpio";
+ };
+ pmx_power_back_on: pmx-power-back-on {
+ marvell,pins = "mpp37";
+ marvell,function = "gpio";
+ };
+ pmx_power_sata0: pmx-power-sata0 {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+ pmx_power_sata1: pmx-power-sata1 {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_present_sata0: pmx-present-sata0 {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_present_sata1: pmx-present-sata1 {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_led_white_usb: pmx-led-white-usb {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ pmx_fan_tacho: pmx-fan-tacho {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+ pmx_fan_high_speed: pmx-fan-high-speed {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ pmx_fan_low_speed: pmx-fan-low-speed {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_button_unmount: pmx-button-unmount {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+ pmx_temp_alarm: pmx-temp-alarm {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+ };
+ sata@80000 {
+ pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
+ pinctrl-names = "default";
+ status = "okay";
+ nr-ports = <2>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
+ pinctrl-names = "default";
+
+ sata0_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 7 0>;
+ };
+ sata1_power: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 8 0>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+ chip-delay = <35>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x500000>;
+ };
+
+ partition@600000 {
+ label = "ramdisk";
+ reg = <0x0600000 0x500000>;
+ };
+
+ partition@b00000 {
+ label = "image";
+ reg = <0x0b00000 0x6600000>;
+ };
+
+ partition@7100000 {
+ label = "mini firmware";
+ reg = <0x7100000 0xa00000>;
+ };
+
+ partition@7b00000 {
+ label = "config";
+ reg = <0x7b00000 0x500000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@8 {
+ reg = <8>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-dockstar.dts b/arch/arm/dts/kirkwood-dockstar.dts
new file mode 100644
index 0000000000..6a3f1bf6d9
--- /dev/null
+++ b/arch/arm/dts/kirkwood-dockstar.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Seagate FreeAgent Dockstar";
+ compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led-green {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led-orange {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+ };
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
+ pinctrl-names = "default";
+
+ health {
+ label = "status:green:health";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ fault {
+ label = "status:orange:fault";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 0>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "data";
+ reg = <0x0500000 0xfb00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "marvell,88e1116";
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-goflexnet.dts b/arch/arm/dts/kirkwood-goflexnet.dts
new file mode 100644
index 0000000000..02d87e0a10
--- /dev/null
+++ b/arch/arm/dts/kirkwood-goflexnet.dts
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Seagate GoFlex Net";
+ compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_0: pmx-led_right_cap_0 {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_1: pmx-led_right_cap_1 {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_2: pmx-led_right_cap_2 {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_led_right_cap_3: pmx-led_right_cap_3 {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_0: pmx-led_left_cap_0 {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_1: pmx-led_left_cap_1 {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_2: pmx-led_left_cap_2 {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+ pmx_led_left_cap_3: pmx-led_left_cap_3 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led_green {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led_orange {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
+ };
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_orange
+ &pmx_led_left_cap_0 &pmx_led_left_cap_1
+ &pmx_led_left_cap_2 &pmx_led_left_cap_3
+ &pmx_led_right_cap_0 &pmx_led_right_cap_1
+ &pmx_led_right_cap_2 &pmx_led_right_cap_3
+ >;
+ pinctrl-names = "default";
+
+ health {
+ label = "status:green:health";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ fault {
+ label = "status:orange:fault";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ left0 {
+ label = "status:white:left0";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+ left1 {
+ label = "status:white:left1";
+ gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+ };
+ left2 {
+ label = "status:white:left2";
+ gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ };
+ left3 {
+ label = "status:white:left3";
+ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ };
+ right0 {
+ label = "status:white:right0";
+ gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ };
+ right1 {
+ label = "status:white:right1";
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+ right2 {
+ label = "status:white:right2";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+ right3 {
+ label = "status:white:right3";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "pogoplug";
+ reg = <0x0500000 0x2000000>;
+ };
+
+ partition@2500000 {
+ label = "root";
+ reg = <0x02500000 0xd800000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/dts/kirkwood-guruplug-server-plus.dts
new file mode 100644
index 0000000000..ff1260ee3f
--- /dev/null
+++ b/arch/arm/dts/kirkwood-guruplug-server-plus.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Globalscale Technologies Guruplug Server Plus";
+ compatible = "globalscale,guruplug-server-plus", "globalscale,guruplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_led_health_r: pmx-led-health-r {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_health_g: pmx-led-health-g {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_led_wmode_r: pmx-led-wmode-r {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+ pmx_led_wmode_g: pmx-led-wmode-g {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <1>;
+ };
+
+ /* AzureWave AW-GH381 WiFi/BT */
+ mvsdio@90000 {
+ status = "okay";
+ non-removable;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g
+ &pmx_led_wmode_r &pmx_led_wmode_g >;
+ pinctrl-names = "default";
+
+ health-r {
+ label = "guruplug:red:health";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+ health-g {
+ label = "guruplug:green:health";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ wmode-r {
+ label = "guruplug:red:wmode";
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ };
+ wmode-g {
+ label = "guruplug:green:wmode";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x00100000 0x00400000>;
+ };
+
+ partition@500000 {
+ label = "data";
+ reg = <0x00500000 0x1fb00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+ð1 {
+ status = "okay";
+ ethernet1-port@0 {
+ phy-handle = <ðphy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
diff --git a/arch/arm/dts/kirkwood-ib62x0.dts b/arch/arm/dts/kirkwood-ib62x0.dts
new file mode 100644
index 0000000000..962a910a6f
--- /dev/null
+++ b/arch/arm/dts/kirkwood-ib62x0.dts
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
+ compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_led_os_red: pmx-led-os-red {
+ marvell,pins = "mpp22";
+ marvell,function = "gpio";
+ };
+ pmx_power_off: pmx-power-off {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+ pmx_led_os_green: pmx-led-os-green {
+ marvell,pins = "mpp25";
+ marvell,function = "gpio";
+ };
+ pmx_led_usb_transfer: pmx-led-usb-transfer {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+ pmx_button_usb_copy: pmx-button-usb-copy {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ };
+
+ serial@12000 {
+ status = "okay";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_button_reset &pmx_button_usb_copy>;
+ pinctrl-names = "default";
+
+ copy {
+ label = "USB Copy";
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+ reset {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_os_red &pmx_led_os_green
+ &pmx_led_usb_transfer>;
+ pinctrl-names = "default";
+
+ green-os {
+ label = "ib62x0:green:os";
+ gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ };
+ red-os {
+ label = "ib62x0:red:os";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ };
+ usb-copy {
+ label = "ib62x0:red:usb_copy";
+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_power_off>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0xe0000>;
+ };
+
+ partition@e0000 {
+ label = "u-boot environment";
+ reg = <0xe0000 0x20000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x600000>;
+ };
+
+ partition@700000 {
+ label = "root";
+ reg = <0x0700000 0xf900000>;
+ };
+
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@8 {
+ reg = <8>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-iconnect.dts b/arch/arm/dts/kirkwood-iconnect.dts
new file mode 100644
index 0000000000..4a512d8091
--- /dev/null
+++ b/arch/arm/dts/kirkwood-iconnect.dts
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Iomega Iconnect";
+ compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ linux,initrd-start = <0x4500040>;
+ linux,initrd-end = <0x4800000>;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+ pmx_button_otb: pmx-button-otb {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+ pmx_led_level: pmx-led-level {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_led_power_blue: pmx-led-power-blue {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_led_power_red: pmx-power-red {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ pmx_led_usb1: pmx-led-usb1 {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+ pmx_led_usb2: pmx-led-usb2 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ pmx_led_usb3: pmx-led-usb3 {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_usb4: pmx-led-usb4 {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_led_otb: pmx-led-otb {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+ };
+ i2c@11000 {
+ status = "okay";
+
+ lm63: lm63@4c {
+ compatible = "national,lm63";
+ reg = <0x4c>;
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_level &pmx_led_power_blue
+ &pmx_led_power_red &pmx_led_usb1
+ &pmx_led_usb2 &pmx_led_usb3
+ &pmx_led_usb4 &pmx_led_otb >;
+ pinctrl-names = "default";
+
+ led-level {
+ label = "led_level";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ power-blue {
+ label = "power:blue";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ };
+ power-red {
+ label = "power:red";
+ gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+ };
+ usb1 {
+ label = "usb1:blue";
+ gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ };
+ usb2 {
+ label = "usb2:blue";
+ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ };
+ usb3 {
+ label = "usb3:blue";
+ gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ usb4 {
+ label = "usb4:blue";
+ gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ };
+ otb {
+ label = "otb:blue";
+ gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = < &pmx_button_reset &pmx_button_otb >;
+ pinctrl-names = "default";
+
+ otb {
+ label = "OTB Button";
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ debounce-interval = <100>;
+ };
+ reset {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ debounce-interval = <100>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0xc0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0xa0000 0x20000>;
+ };
+
+ partition@100000 {
+ label = "zImage";
+ reg = <0x100000 0x300000>;
+ };
+
+ partition@540000 {
+ label = "initrd";
+ reg = <0x540000 0x300000>;
+ };
+
+ partition@980000 {
+ label = "boot";
+ reg = <0x980000 0x1f400000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@11 {
+ reg = <11>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/kirkwood-openrd-base.dts b/arch/arm/dts/kirkwood-openrd-base.dts
new file mode 100644
index 0000000000..094191ece3
--- /dev/null
+++ b/arch/arm/dts/kirkwood-openrd-base.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell OpenRD Base Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file contains the definitions that are specific to OpenRD
+ * base variant of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood-openrd.dtsi"
+
+/ {
+ model = "OpenRD Base";
+ compatible = "marvell,openrd-base", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ ocp@f1000000 {
+ serial@12100 {
+ status = "okay";
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@8 {
+ reg = <8>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-openrd-client.dts b/arch/arm/dts/kirkwood-openrd-client.dts
new file mode 100644
index 0000000000..74dc23daf6
--- /dev/null
+++ b/arch/arm/dts/kirkwood-openrd-client.dts
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell OpenRD Client Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file contains the definitions that are specific to OpenRD
+ * client variant of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood-openrd.dtsi"
+
+/ {
+ model = "OpenRD Client";
+ compatible = "marvell,openrd-client", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ ocp@f1000000 {
+ audio-controller@a0000 {
+ status = "okay";
+ };
+ i2c@11000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ cs42l51: cs42l51@4a {
+ compatible = "cirrus,cs42l51";
+ reg = <0x4a>;
+ #sound-dai-cells = <0>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&audio0 0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&cs42l51>;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@8 {
+ reg = <8>;
+ };
+ ethphy1: ethernet-phy@24 {
+ reg = <24>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+ ethernet1-port@0 {
+ phy-handle = <ðphy1>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-openrd-ultimate.dts b/arch/arm/dts/kirkwood-openrd-ultimate.dts
new file mode 100644
index 0000000000..888e13320c
--- /dev/null
+++ b/arch/arm/dts/kirkwood-openrd-ultimate.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell OpenRD Ultimate Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file contains the definitions that are specific to OpenRD
+ * ultimate variant of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood-openrd.dtsi"
+
+/ {
+ model = "OpenRD Ultimate";
+ compatible = "marvell,openrd-ultimate", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ ocp@f1000000 {
+ i2c@11000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ cs42l51: cs42l51@4a {
+ compatible = "cirrus,cs42l51";
+ reg = <0x4a>;
+ };
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+ ethernet1-port@0 {
+ phy-handle = <ðphy1>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-openrd.dtsi b/arch/arm/dts/kirkwood-openrd.dtsi
new file mode 100644
index 0000000000..47f03c69c5
--- /dev/null
+++ b/arch/arm/dts/kirkwood-openrd.dtsi
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell OpenRD (Base|Client|Ultimate) Board Description
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file contains the definitions that are common between the three
+ * variants of the Marvell Kirkwood Development Board.
+ */
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pinctrl-0 = <&pmx_select28 &pmx_sdio_cd &pmx_select34>;
+ pinctrl-names = "default";
+
+ pmx_select28: pmx-select-rs232-rs485 {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+ pmx_sdio_cd: pmx-sdio-cd {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_select34: pmx-select-uart-sd {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "okay";
+
+ };
+ sata@80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+ mvsdio@90000 {
+ status = "okay";
+ cd-gpios = <&gpio0 29 9>;
+ };
+ gpio@10100 {
+ p28 {
+ gpio-hog;
+ gpios = <28 GPIO_ACTIVE_HIGH>;
+ /*
+ * SelRS232or485 selects between RS-232 or RS-485
+ * mode for the second UART.
+ *
+ * Low: RS-232
+ * High: RS-485
+ *
+ * To use the second UART, you need to change also
+ * the SelUARTorSD.
+ */
+ output-low;
+ line-name = "SelRS232or485";
+ };
+ };
+ gpio@10140 {
+ p2 {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ /*
+ * SelUARTorSD selects between the second UART
+ * (serial@12100) and SD (mvsdio@90000).
+ *
+ * Low: UART
+ * High: SD
+ *
+ * When changing this line make sure the newly
+ * selected device node is enabled and the
+ * previously selected device node is disabled.
+ */
+ output-high; /* Select SD by default */
+ line-name = "SelUARTorSD";
+ };
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@600000 {
+ label = "root";
+ reg = <0x0600000 0x1FA00000>;
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/kirkwood-pogo_e02.dts b/arch/arm/dts/kirkwood-pogo_e02.dts
new file mode 100644
index 0000000000..f9e95e55f3
--- /dev/null
+++ b/arch/arm/dts/kirkwood-pogo_e02.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * kirkwood-pogo_e02.dts - Device tree file for Pogoplug E02
+ *
+ * Copyright (C) 2015 Christoph Junghans <ottxor@gentoo.org>
+ *
+ * based on information of dts files from
+ * Arch Linux ARM by Oleg Rakhmanov <moonman.ca@gmail.com>
+ * OpenWrt by Felix Kaechele <heffer@fedoraproject.org>
+ *
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Cloud Engines Pogoplug E02";
+ compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281",
+ "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ health {
+ label = "pogo_e02:green:health";
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ fault {
+ label = "pogo_e02:orange:fault";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+ &pmx_led_green >;
+ pinctrl-names = "default";
+
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_green: pmx-led-green {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_orange: pmx-led-orange {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "pogoplug";
+ reg = <0x0500000 0x2000000>;
+ };
+
+ partition@2500000 {
+ label = "root";
+ reg = <0x02500000 0x5b00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/dts/kirkwood-sheevaplug-common.dtsi
new file mode 100644
index 0000000000..0a698d3b73
--- /dev/null
+++ b/arch/arm/dts/kirkwood-sheevaplug-common.dtsi
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * kirkwood-sheevaplug-common.dtsi - Common parts for Sheevaplugs
+ *
+ * Copyright (C) 2013 Simon Baatz <gmbnomis@gmail.com>
+ */
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_red: pmx-led-red {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_blue: pmx-led-blue {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+ pmx_sdio_cd: pmx-sdio-cd {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+ pmx_sdio_wp: pmx-sdio-wp {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "okay";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 0>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "root";
+ reg = <0x0500000 0x1fb00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/dts/kirkwood-sheevaplug.dts b/arch/arm/dts/kirkwood-sheevaplug.dts
new file mode 100644
index 0000000000..c73cc904e5
--- /dev/null
+++ b/arch/arm/dts/kirkwood-sheevaplug.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * kirkwood-sheevaplug.dts - Device tree file for Sheevaplug
+ *
+ * Copyright (C) 2013 Simon Baatz <gmbnomis@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood-sheevaplug-common.dtsi"
+
+/ {
+ model = "Globalscale Technologies SheevaPlug";
+ compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ ocp@f1000000 {
+ mvsdio@90000 {
+ pinctrl-0 = <&pmx_sdio>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ broken-cd;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_blue &pmx_led_red>;
+ pinctrl-names = "default";
+
+ health {
+ label = "sheevaplug:blue:health";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ misc {
+ label = "sheevaplug:red:misc";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
diff --git a/arch/arm/dts/kirkwood.dtsi b/arch/arm/dts/kirkwood.dtsi
new file mode 100644
index 0000000000..81c7eda2c4
--- /dev/null
+++ b/arch/arm/dts/kirkwood.dtsi
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0
+/include/ "skeleton.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+ compatible = "marvell,kirkwood";
+ interrupt-parent = <&intc>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "marvell,feroceon";
+ reg = <0>;
+ clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>;
+ clock-names = "cpu_clk", "ddrclk", "powersave";
+ };
+ };
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ i2c0 = &i2c0;
+ };
+
+ mbus@f1000000 {
+ compatible = "marvell,kirkwood-mbus", "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* If a board file needs to change this ranges it must replace it completely */
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
+ MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
+ MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
+ >;
+ controller = <&mbusc>;
+ pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
+ pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
+
+ nand: nand@12f {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cle = <0>;
+ ale = <1>;
+ bank-width = <1>;
+ compatible = "marvell,orion-nand";
+ reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
+ chip-delay = <25>;
+ /* set partition map and/or chip-delay in board dts */
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ crypto_sram: sa-sram@301 {
+ compatible = "mmio-sram";
+ reg = <MBUS_ID(0x03, 0x01) 0x0 0x800>;
+ clocks = <&gate_clk 17>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+
+ ocp@f1000000 {
+ compatible = "simple-bus";
+ ranges = <0x00000000 0xf1000000 0x0100000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pinctrl: pin-controller@10000 {
+ /* set compatible property in SoC file */
+ reg = <0x10000 0x20>;
+
+ pmx_ge1: pmx-ge1 {
+ marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23",
+ "mpp24", "mpp25", "mpp26", "mpp27",
+ "mpp30", "mpp31", "mpp32", "mpp33";
+ marvell,function = "ge1";
+ };
+
+ pmx_nand: pmx-nand {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
+ "mpp4", "mpp5", "mpp18", "mpp19";
+ marvell,function = "nand";
+ };
+
+ /*
+ * Default SPI0 pinctrl setting with CSn on mpp0,
+ * overwrite marvell,pins on board level if required.
+ */
+ pmx_spi: pmx-spi {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3";
+ marvell,function = "spi";
+ };
+
+ pmx_twsi0: pmx-twsi0 {
+ marvell,pins = "mpp8", "mpp9";
+ marvell,function = "twsi0";
+ };
+
+ /*
+ * Default UART pinctrl setting without RTS/CTS,
+ * overwrite marvell,pins on board level if required.
+ */
+ pmx_uart0: pmx-uart0 {
+ marvell,pins = "mpp10", "mpp11";
+ marvell,function = "uart0";
+ };
+
+ pmx_uart1: pmx-uart1 {
+ marvell,pins = "mpp13", "mpp14";
+ marvell,function = "uart1";
+ };
+ };
+
+ core_clk: core-clocks@10030 {
+ compatible = "marvell,kirkwood-core-clock";
+ reg = <0x10030 0x4>;
+ #clock-cells = <1>;
+ };
+
+ spi0: spi@10600 {
+ compatible = "marvell,orion-spi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <23>;
+ reg = <0x10600 0x28>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_spi>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ gpio0: gpio@10100 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x10100 0x40>;
+ ngpios = <32>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <35>, <36>, <37>, <38>;
+ clocks = <&gate_clk 7>;
+ };
+
+ gpio1: gpio@10140 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x10140 0x40>;
+ ngpios = <18>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <39>, <40>, <41>;
+ clocks = <&gate_clk 7>;
+ };
+
+ i2c0: i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <29>;
+ clock-frequency = <100000>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_twsi0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ uart0: serial@12000 {
+ compatible = "ns16550a";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <33>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_uart0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ uart1: serial@12100 {
+ compatible = "ns16550a";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ interrupts = <34>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_uart1>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ mbusc: mbus-controller@20000 {
+ compatible = "marvell,mbus-controller";
+ reg = <0x20000 0x80>, <0x1500 0x20>;
+ };
+
+ sysc: system-controller@20000 {
+ compatible = "marvell,orion-system-controller";
+ reg = <0x20000 0x120>;
+ };
+
+ bridge_intc: bridge-interrupt-ctrl@20110 {
+ compatible = "marvell,orion-bridge-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20110 0x8>;
+ interrupts = <1>;
+ marvell,#interrupts = <6>;
+ };
+
+ gate_clk: clock-gating-control@2011c {
+ compatible = "marvell,kirkwood-gating-clock";
+ reg = <0x2011c 0x4>;
+ clocks = <&core_clk 0>;
+ #clock-cells = <1>;
+ };
+
+ l2: l2-cache@20128 {
+ compatible = "marvell,kirkwood-cache";
+ reg = <0x20128 0x4>;
+ };
+
+ intc: main-interrupt-ctrl@20200 {
+ compatible = "marvell,orion-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20200 0x10>, <0x20210 0x10>;
+ };
+
+ timer: timer@20300 {
+ compatible = "marvell,orion-timer";
+ reg = <0x20300 0x20>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <1>, <2>;
+ clocks = <&core_clk 0>;
+ };
+
+ wdt: watchdog-timer@20300 {
+ compatible = "marvell,orion-wdt";
+ reg = <0x20300 0x28>, <0x20108 0x4>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <3>;
+ clocks = <&gate_clk 7>;
+ status = "okay";
+ };
+
+ cesa: crypto@30000 {
+ compatible = "marvell,kirkwood-crypto";
+ reg = <0x30000 0x10000>;
+ reg-names = "regs";
+ interrupts = <22>;
+ clocks = <&gate_clk 17>;
+ marvell,crypto-srams = <&crypto_sram>;
+ marvell,crypto-sram-size = <0x800>;
+ status = "okay";
+ };
+
+ usb0: ehci@50000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x50000 0x1000>;
+ interrupts = <19>;
+ clocks = <&gate_clk 3>;
+ status = "okay";
+ };
+
+ dma0: xor@60800 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60800 0x100
+ 0x60A00 0x100>;
+ status = "okay";
+ clocks = <&gate_clk 8>;
+
+ xor00 {
+ interrupts = <5>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <6>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ dma1: xor@60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60B00 0x100>;
+ status = "okay";
+ clocks = <&gate_clk 16>;
+
+ xor00 {
+ interrupts = <7>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <8>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ eth0: ethernet-controller@72000 {
+ compatible = "marvell,kirkwood-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72000 0x4000>;
+ clocks = <&gate_clk 0>;
+ marvell,tx-checksum-limit = <1600>;
+ status = "disabled";
+
+ eth0port: ethernet0-port@0 {
+ compatible = "marvell,kirkwood-eth-port";
+ reg = <0>;
+ interrupts = <11>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ /* set phy-handle property in board file */
+ };
+ };
+
+ mdio: mdio-bus@72004 {
+ compatible = "marvell,orion-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72004 0x84>;
+ interrupts = <46>;
+ clocks = <&gate_clk 0>;
+ status = "disabled";
+
+ /* add phy nodes in board file */
+ };
+
+ eth1: ethernet-controller@76000 {
+ compatible = "marvell,kirkwood-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76000 0x4000>;
+ clocks = <&gate_clk 19>;
+ marvell,tx-checksum-limit = <1600>;
+ pinctrl-0 = <&pmx_ge1>;
+ pinctrl-names = "default";
+ status = "disabled";
+
+ eth1port: ethernet1-port@0 {
+ compatible = "marvell,kirkwood-eth-port";
+ reg = <0>;
+ interrupts = <15>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ /* set phy-handle property in board file */
+ };
+ };
+
+ sata_phy0: sata-phy@82000 {
+ compatible = "marvell,mvebu-sata-phy";
+ reg = <0x82000 0x0334>;
+ clocks = <&gate_clk 14>;
+ clock-names = "sata";
+ #phy-cells = <0>;
+ status = "ok";
+ };
+
+ sata_phy1: sata-phy@84000 {
+ compatible = "marvell,mvebu-sata-phy";
+ reg = <0x84000 0x0334>;
+ clocks = <&gate_clk 15>;
+ clock-names = "sata";
+ #phy-cells = <0>;
+ status = "ok";
+ };
+
+ audio0: audio-controller@a0000 {
+ compatible = "marvell,kirkwood-audio";
+ #sound-dai-cells = <0>;
+ reg = <0xa0000 0x2210>;
+ interrupts = <24>;
+ clocks = <&gate_clk 9>;
+ clock-names = "internal";
+ status = "disabled";
+ };
+ };
+};
diff --git a/configs/dns325_defconfig b/configs/dns325_defconfig
index f64038dfe0..f0ed209928 100644
--- a/configs/dns325_defconfig
+++ b/configs/dns325_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_DNS325=y
CONFIG_IDENT_STRING="\nD-Link DNS-325"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dns325"
CONFIG_BOOTDELAY=3
CONFIG_CONSOLE_MUX=y
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -23,6 +24,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:896k(u-boot),128k(u-boot-env),5m(kernel),-(rootfs)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
@@ -32,4 +34,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/dockstar_defconfig b/configs/dockstar_defconfig
index b7a65db37c..1ed5cfe7d4 100644
--- a/configs/dockstar_defconfig
+++ b/configs/dockstar_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_DOCKSTAR=y
CONFIG_IDENT_STRING="\nSeagate FreeAgent DockStar"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dockstar"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_PROMPT="DockStar> "
@@ -19,6 +20,7 @@ CONFIG_CMD_JFFS2=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:1m(uboot),-(root)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
# CONFIG_MMC is not set
CONFIG_NETDEVICES=y
@@ -27,4 +29,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/goflexhome_defconfig b/configs/goflexhome_defconfig
index 3b3abd52c7..c0894c05ea 100644
--- a/configs/goflexhome_defconfig
+++ b/configs/goflexhome_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_GOFLEXHOME=y
CONFIG_IDENT_STRING="\nSeagate GoFlex Home"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-goflexnet"
CONFIG_BOOTDELAY=3
CONFIG_CONSOLE_MUX=y
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:1m(uboot),6M(uImage),-(root)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
@@ -33,4 +35,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/guruplug_defconfig b/configs/guruplug_defconfig
index 5389cdd07e..da3895d4db 100644
--- a/configs/guruplug_defconfig
+++ b/configs/guruplug_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_GURUPLUG=y
CONFIG_IDENT_STRING="\nMarvell-GuruPlug"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-guruplug-server-plus"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:896K(uboot),128K(uboot_env),-@1M(root)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
@@ -34,4 +36,3 @@ CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/ib62x0_defconfig b/configs/ib62x0_defconfig
index cb629bbfb9..20a26d4505 100644
--- a/configs/ib62x0_defconfig
+++ b/configs/ib62x0_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_IB62X0=y
CONFIG_IDENT_STRING=" RaidSonic ICY BOX IB-NAS62x0"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ib62x0"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -22,6 +23,7 @@ CONFIG_CMD_JFFS2=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xe0000@0x0(uboot),0x20000@0xe0000(uboot_env),-@0x100000(root)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
@@ -32,4 +34,3 @@ CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/iconnect_defconfig b/configs/iconnect_defconfig
index bdd01d1387..736db90cd7 100644
--- a/configs/iconnect_defconfig
+++ b/configs/iconnect_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_ICONNECT=y
CONFIG_IDENT_STRING=" Iomega iConnect"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-iconnect"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_PROMPT="iconnect => "
@@ -18,6 +19,7 @@ CONFIG_CMD_JFFS2=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0x80000@0x0(uboot),0x20000@0x80000(uboot_env),-@0xa0000(rootfs)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
# CONFIG_MMC is not set
CONFIG_NETDEVICES=y
@@ -27,4 +29,3 @@ CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/nas220_defconfig b/configs/nas220_defconfig
index 0299e0a707..ddf5689bf4 100644
--- a/configs/nas220_defconfig
+++ b/configs/nas220_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_NAS220=y
CONFIG_IDENT_STRING="\nNAS 220"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-blackarmor-nas220"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -24,6 +25,7 @@ CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
CONFIG_EFI_PARTITION=y
# CONFIG_PARTITION_UUIDS is not set
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
@@ -33,4 +35,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/openrd_base_defconfig b/configs/openrd_base_defconfig
index 003fb172ed..3b4724f1fc 100644
--- a/configs/openrd_base_defconfig
+++ b/configs/openrd_base_defconfig
@@ -4,6 +4,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_OPENRD=y
CONFIG_IDENT_STRING="\nOpenRD-Base"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-base"
CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_BASE"
CONFIG_BOOTDELAY=3
CONFIG_LOGLEVEL=2
@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd"
CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000@0x000000(uboot),0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC_HW_PARTITIONING is not set
@@ -33,4 +35,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/openrd_client_defconfig b/configs/openrd_client_defconfig
index fbc5b17b13..a2d86b5690 100644
--- a/configs/openrd_client_defconfig
+++ b/configs/openrd_client_defconfig
@@ -4,6 +4,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_OPENRD=y
CONFIG_IDENT_STRING="\nOpenRD-Client"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-client"
CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_CLIENT"
CONFIG_BOOTDELAY=3
CONFIG_LOGLEVEL=2
@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd"
CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000@0x000000(uboot),0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC_HW_PARTITIONING is not set
@@ -33,4 +35,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/openrd_ultimate_defconfig b/configs/openrd_ultimate_defconfig
index bba1bbeb7a..156fa3ff1f 100644
--- a/configs/openrd_ultimate_defconfig
+++ b/configs/openrd_ultimate_defconfig
@@ -4,6 +4,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_OPENRD=y
CONFIG_IDENT_STRING="\nOpenRD-Ultimate"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-ultimate"
CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_ULTIMATE"
CONFIG_BOOTDELAY=3
CONFIG_LOGLEVEL=2
@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd"
CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000@0x000000(uboot),0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC_HW_PARTITIONING is not set
@@ -33,4 +35,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/pogo_e02_defconfig b/configs/pogo_e02_defconfig
index 6d1af7748d..0c4c023406 100644
--- a/configs/pogo_e02_defconfig
+++ b/configs/pogo_e02_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_POGO_E02=y
CONFIG_IDENT_STRING="\nPogo E02"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogo_e02"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_PROMPT="PogoE02> "
@@ -18,6 +19,7 @@ CONFIG_CMD_FAT=y
CONFIG_CMD_JFFS2=y
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
# CONFIG_MMC is not set
CONFIG_NETDEVICES=y
@@ -26,4 +28,3 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/sheevaplug_defconfig b/configs/sheevaplug_defconfig
index 25a8e5340e..608e05e64e 100644
--- a/configs/sheevaplug_defconfig
+++ b/configs/sheevaplug_defconfig
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_SHEEVAPLUG=y
CONFIG_IDENT_STRING="\nMarvell-Sheevaplug"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-sheevaplug"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -25,6 +26,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:512K(uboot),512K(env),4M(kernel),-(rootfs)"
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_MVSATA_IDE=y
CONFIG_NETDEVICES=y
@@ -34,4 +36,3 @@ CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index c962d7a72c..f2cc75f494 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -181,7 +181,6 @@ config FTMAC100
config MVGBE
bool "Marvell Orion5x/Kirkwood network interface support"
depends on KIRKWOOD || ORION5X
- select PHYLIB
help
This driver supports the network interface units in the
Marvell Orion5x and Kirkwood SoCs