Coding Style cleanup: drop some excessive empty lines

Signed-off-by: Wolfgang Denk <wd@denx.de>

board/LEOX/elpt860/README.LEOX

@@ -46,7 +46,6 @@ U-Boot, at the address of 0x03000000.
 
 =============================================================================
 
-
 ##################################################
 # Operation on the serial console (SMC1)
 ##############################

board/palmtreo680/README

@@ -30,7 +30,6 @@ go wrong, but please tell me what happened exactly.  For that matter, I'd love
 to hear from you if you succeed.
 
 
-
 Details on the SPL
 ==================
 
@@ -51,7 +50,6 @@ IPL has already loaded to its correct SDRAM address, and then loads the
 remainder of u-boot and jumps to it.
 
 
-
 The docg4's "reliable mode"
 ===========================
 
@@ -79,7 +77,6 @@ module parameter), but not reading.  However, the u-boot docg4_spl driver does
 read in reliable mode, in the same fashion as the IPL.
 
 
-
 Details on the IPL and its data format
 ======================================
 
@@ -105,7 +102,6 @@ For the sake of simplicity and uniformity, the u-boot SPL mimics the operation
 of the IPL, and expects the image to be stored in the same format.
 
 
-
 Instructions on Programming u-boot to flash
 ===========================================
 
@@ -117,7 +113,6 @@ remainder of this document describes in detail how to program u-boot to the
 flash using Linux running on the Treo.
 
 
-
 Hardware Prerequisites
 ======================
 
@@ -136,7 +131,6 @@ A Linux desktop PC.
   to flash, you'll really want to use a Linux PC.
 
 
-
 Treo-side Software Prerequisites
 ================================
 
@@ -152,7 +146,6 @@ Linux bootloader for PalmOS:
   parameters passed to the kernel.
 
 
-
 Linux kernel:
 
   The kernel on the Treo 680 is still a little rough around the edges, and the
@@ -200,7 +193,6 @@ Linux kernel:
   and /dev/mtd2 for these partitions, respectively.  Ensure that your root file
   system at least has /dev/mtd1 if you are not running udev or mdev.
 
-
 Userspace Utilities:
 
   In addition to everything necessary to provide a useful userspace environment
@@ -221,19 +213,16 @@ Userspace Utilities:
   from the mtd-utils package.
 
 
-
 Desktop PC-side Software Prerequisites
 ======================================
 
 Terminal emulator application:
   minicom, kermit, etc.
 
-
 Linux kernel:
   Compiled with CONFIG_USB_SERIAL enabled.  Build this as a module.
 
 
-
 Recommended (Not directly related to u-boot)
 ============================================
 
@@ -275,7 +264,6 @@ configure the usb0 interface on the desktop.)  Use the nfs 'nolock' option when
 mounting to avoid the need to run a portmapper like rpcbind.
 
 
-
 Preliminaries
 =============
 
@@ -397,7 +385,6 @@ forget to copy the file to permanent storage, such as an mmc card.
 If all of the above went well, you can now program u-boot.
 
 
-
 Programming u-boot
 ==================
 
@@ -438,7 +425,6 @@ four blocks in /dev/mtd1; i.e., at offsets 0x00000, 0x40000, 0x80000, 0xc0000.
 Shutdown linux, remove and re-insert the battery, hold your breath...
 
 
-
 Enjoying u-boot
 ===============
 
@@ -478,7 +464,6 @@ support for reliable mode in u-boot's docg4 flash driver.  This should be
 corrected soon.
 
 
-
 Customizing
 ===========
 
@@ -511,7 +496,6 @@ in flash did not seem worth the cost of a 256k flash block.  But adding this
 should be straightforward.
 
 
-
 Restoring PalmOS
 ================
 
@@ -568,7 +552,6 @@ modprobe docg4 ignore_badblocks=1 || exit 1
 dd if=$1 bs=1 skip=$file_ofs count=540672 | nandwrite -o -n -s 0x80000 $2 - || exit 1
 modprobe -r docg4
 
-
 TODO
 ====
 

board/sandpoint/README

@@ -15,8 +15,6 @@ tkoeller@gmx.net.
 Thomas Koeller
 
 
-
-
 The port was tested on a Sandpoint 8240 X3 board, with U-Boot
 installed in the flash memory of the CPU card. Please use the
 following DIP switch settings:

board/siemens/rut/board.c

@@ -328,8 +328,6 @@ static int get_clk(struct dpll_regs *dpll_regs)
 	return f;
 };
 
-
-
 int clk_get(int clk)
 {
 	return get_clk(&dpll_lcd_regs);
@@ -426,7 +424,5 @@ static int board_video_init(void)
 
 	return 0;
 }
-
-
 #endif /* ifdef CONFIG_VIDEO */
 #include "../common/board.c"