Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze

Xilinx/FPGA changes for v2019.07

fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq

arm:
- Tune zynq command functions
- Fix internal variable setting

arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case

spi:
- Fix tap delay programming

clk:
- Enable i2c in SPL

net:
- Fix gem phydev handling
- Remove phy detection code from gem driver

general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration

include/configs/xilinx_zynqmp.h

@@ -108,15 +108,6 @@
 # define PHY_ANEG_TIMEOUT       20000
 #endif
 
-/* EEPROM */
-#ifdef CONFIG_ZYNQMP_EEPROM
-# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-# define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
-# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
-# define CONFIG_SYS_EEPROM_SIZE			(64 * 1024)
-#endif
-
 #define CONFIG_SYS_BOOTM_LEN	(60 * 1024 * 1024)
 
 #define CONFIG_CLOCKS

include/configs/zynq-common.h

@@ -69,7 +69,7 @@
 # define CONFIG_THOR_RESET_OFF
 # define DFU_ALT_INFO_RAM \
 	"dfu_ram_info=" \
-	"set dfu_alt_info " \
+	"setenv dfu_alt_info " \
 	"${kernel_image} ram 0x3000000 0x500000\\\\;" \
 	"${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
 	"${ramdisk_image} ram 0x2000000 0x600000\0" \
@@ -79,7 +79,7 @@
 # if defined(CONFIG_MMC_SDHCI_ZYNQ)
 #  define DFU_ALT_INFO_MMC \
 	"dfu_mmc_info=" \
-	"set dfu_alt_info " \
+	"setenv dfu_alt_info " \
 	"${kernel_image} fat 0 1\\\\;" \
 	"${devicetree_image} fat 0 1\\\\;" \
 	"${ramdisk_image} fat 0 1\0" \
@@ -227,9 +227,9 @@
 				"env run importbootenv; " \
 			"fi; " \
 		"fi; \0" \
-	"sd_loadbootenv=set bootenv_dev mmc && " \
+	"sd_loadbootenv=setenv bootenv_dev mmc && " \
 			"run setbootenv \0" \
-	"usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \
+	"usb_loadbootenv=setenv bootenv_dev usb && usb start && run setbootenv \0" \
 	"preboot=if test $modeboot = sdboot; then " \
 			"run sd_loadbootenv; " \
 			"echo Checking if uenvcmd is set ...; " \