Merge git://git.denx.de/u-boot-fsl-qoriq

board/freescale/common/Makefile

@@ -61,6 +61,7 @@ obj-$(CONFIG_VSC_CROSSBAR)    += vsc3316_3308.o
 obj-$(CONFIG_IDT8T49N222A)	+= idt8t49n222a_serdes_clk.o
 obj-$(CONFIG_ZM7300)		+= zm7300.o
 obj-$(CONFIG_POWER_PFUZE100)	+= pfuze.o
+obj-$(CONFIG_POWER_MC34VR500)	+= mc34vr500.o
 
 obj-$(CONFIG_LS102XA_STREAM_ID)	+= ls102xa_stream_id.o
 

board/freescale/common/mc34vr500.c

@@ -0,0 +1,95 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ * Hou Zhiqiang <Zhiqiang.Hou@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <i2c.h>
+#include <power/pmic.h>
+#include <power/mc34vr500_pmic.h>
+
+static uint8_t swxvolt_addr[4] = { MC34VR500_SW1VOLT,
+				   MC34VR500_SW2VOLT,
+				   MC34VR500_SW3VOLT,
+				   MC34VR500_SW4VOLT };
+
+static uint8_t swx_set_point_base[4] = { 13, 9, 9, 9 };
+
+int mc34vr500_get_sw_volt(uint8_t sw)
+{
+	struct pmic *p;
+	u32 swxvolt;
+	uint8_t spb;
+	int sw_volt;
+	int ret;
+
+	debug("%s: Get SW%u volt from swxvolt_addr = 0x%x\n",
+	      __func__, sw + 1, swxvolt_addr[sw]);
+	if (sw > SW4) {
+		printf("%s: Unsupported SW(sw%d)\n", __func__, sw + 1);
+		return -EINVAL;
+	}
+
+	p = pmic_get("MC34VR500");
+	if (!p) {
+		printf("%s: Did NOT find PMIC MC34VR500\n", __func__);
+		return -ENODEV;
+	}
+
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	ret = pmic_reg_read(p, swxvolt_addr[sw], &swxvolt);
+	if (ret) {
+		printf("%s: Failed to get SW%u volt\n", __func__, sw + 1);
+		return ret;
+	}
+
+	debug("%s: SW%d step point swxvolt = %u\n", __func__, sw + 1, swxvolt);
+	spb = swx_set_point_base[sw];
+	/* The base of SW volt is 625mV and increase by step 25mV */
+	sw_volt = 625 + (swxvolt - spb) * 25;
+
+	debug("%s: SW%u volt = %dmV\n", __func__, sw + 1, sw_volt);
+	return sw_volt;
+}
+
+int mc34vr500_set_sw_volt(uint8_t sw, int sw_volt)
+{
+	struct pmic *p;
+	u32 swxvolt;
+	uint8_t spb;
+	int ret;
+
+	debug("%s: Set SW%u volt to %dmV\n", __func__, sw + 1, sw_volt);
+	/* The least SW volt is 625mV, and only 4 SW outputs */
+	if (sw > SW4 || sw_volt < 625)
+		return -EINVAL;
+
+	p = pmic_get("MC34VR500");
+	if (!p) {
+		printf("%s: Did NOT find PMIC MC34VR500\n", __func__);
+		return -ENODEV;
+	}
+
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	spb = swx_set_point_base[sw];
+	/* The base of SW volt is 625mV and increase by step 25mV */
+	swxvolt = (sw_volt - 625) / 25 + spb;
+	debug("%s: SW%d step point swxvolt = %u\n", __func__, sw + 1, swxvolt);
+	if (swxvolt > 63)
+		return -EINVAL;
+
+	ret = pmic_reg_write(p, swxvolt_addr[sw], swxvolt);
+	if (ret)
+		return ret;
+
+	return 0;
+}

board/freescale/ls1012aqds/ls1012aqds.c

@@ -121,6 +121,34 @@ int board_eth_init(bd_t *bis)
 	return pci_eth_init(bis);
 }
 
+int esdhc_status_fixup(void *blob, const char *compat)
+{
+	char esdhc0_path[] = "/soc/esdhc@1560000";
+	char esdhc1_path[] = "/soc/esdhc@1580000";
+	u8 card_id;
+
+	do_fixup_by_path(blob, esdhc0_path, "status", "okay",
+			 sizeof("okay"), 1);
+
+	/*
+	 * The Presence Detect 2 register detects the installation
+	 * of cards in various PCI Express or SGMII slots.
+	 *
+	 * STAT_PRS2[7:5]: Specifies the type of card installed in the
+	 * SDHC2 Adapter slot. 0b111 indicates no adapter is installed.
+	 */
+	card_id = (QIXIS_READ(present2) & 0xe0) >> 5;
+
+	/* If no adapter is installed in SDHC2, disable SDHC2 */
+	if (card_id == 0x7)
+		do_fixup_by_path(blob, esdhc1_path, "status", "disabled",
+				 sizeof("disabled"), 1);
+	else
+		do_fixup_by_path(blob, esdhc1_path, "status", "okay",
+				 sizeof("okay"), 1);
+	return 0;
+}
+
 #ifdef CONFIG_OF_BOARD_SETUP
 int ft_board_setup(void *blob, bd_t *bd)
 {

board/freescale/ls1012ardb/ls1012ardb.c

@@ -113,6 +113,44 @@ int board_init(void)
 	return 0;
 }
 
+int esdhc_status_fixup(void *blob, const char *compat)
+{
+	char esdhc0_path[] = "/soc/esdhc@1560000";
+	char esdhc1_path[] = "/soc/esdhc@1580000";
+	u8 io = 0;
+	u8 mux_sdhc2;
+
+	do_fixup_by_path(blob, esdhc0_path, "status", "okay",
+			 sizeof("okay"), 1);
+
+	i2c_set_bus_num(0);
+
+	/*
+	 * The I2C IO-expander for mux select is used to control the muxing
+	 * of various onboard interfaces.
+	 *
+	 * IO1[3:2] indicates SDHC2 interface demultiplexer select lines.
+	 *	00 - SDIO wifi
+	 *	01 - GPIO (to Arduino)
+	 *	10 - eMMC Memory
+	 *	11 - SPI
+	 */
+	if (i2c_read(I2C_MUX_IO1_ADDR, 0, 1, &io, 1) < 0) {
+		printf("Error reading i2c boot information!\n");
+		return 0; /* Don't want to hang() on this error */
+	}
+
+	mux_sdhc2 = (io & 0x0c) >> 2;
+	/* Enable SDHC2 only when use SDIO wifi and eMMC */
+	if (mux_sdhc2 == 2 || mux_sdhc2 == 0)
+		do_fixup_by_path(blob, esdhc1_path, "status", "okay",
+				 sizeof("okay"), 1);
+	else
+		do_fixup_by_path(blob, esdhc1_path, "status", "disabled",
+				 sizeof("disabled"), 1);
+	return 0;
+}
+
 int ft_board_setup(void *blob, bd_t *bd)
 {
 	arch_fixup_fdt(blob);

board/freescale/ls1046ardb/cpld.c

@@ -82,6 +82,15 @@ void cpld_set_sd(void)
 
 	CPLD_WRITE(system_rst, 1);
 }
+
+void cpld_select_core_volt(bool en_0v9)
+{
+	u8 reg17 = en_0v9;
+
+	CPLD_WRITE(vdd_en, 1);
+	CPLD_WRITE(vdd_sel, reg17);
+}
+
 #ifdef DEBUG
 static void cpld_dump_regs(void)
 {

board/freescale/ls1046ardb/cpld.h

@@ -35,6 +35,7 @@ struct cpld_data {
 u8 cpld_read(unsigned int reg);
 void cpld_write(unsigned int reg, u8 value);
 void cpld_rev_bit(unsigned char *value);
+void cpld_select_core_volt(bool en_0v9);
 
 #define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
 #define CPLD_WRITE(reg, value)  \

board/freescale/ls1046ardb/ls1046ardb.c

@@ -19,6 +19,7 @@
 #include <fm_eth.h>
 #include <fsl_csu.h>
 #include <fsl_esdhc.h>
+#include <power/mc34vr500_pmic.h>
 #include "cpld.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -87,6 +88,39 @@ int board_init(void)
 	return 0;
 }
 
+int board_setup_core_volt(u32 vdd)
+{
+	bool en_0v9;
+
+	en_0v9 = (vdd == 900) ? true : false;
+	cpld_select_core_volt(en_0v9);
+
+	return 0;
+}
+
+int get_serdes_volt(void)
+{
+	return mc34vr500_get_sw_volt(SW4);
+}
+
+int set_serdes_volt(int svdd)
+{
+	return mc34vr500_set_sw_volt(SW4, svdd);
+}
+
+int power_init_board(void)
+{
+	int ret;
+
+	ret = power_mc34vr500_init(0);
+	if (ret)
+		return ret;
+
+	setup_chip_volt();
+
+	return 0;
+}
+
 void config_board_mux(void)
 {
 #ifdef CONFIG_HAS_FSL_XHCI_USB