leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
c3c19c2743
u-boot/configs/gt90h_v4_defconfig

27 lines
823 B
Plaintext
Raw Normal View History

sunxi: Add support for gt90h-v4 tablets The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot. The pmic setup on this board is somewhat special, dcdc2 MUST be set to 1.1V instead of the usual 1.2V otherwise the board is very unstable. aldo1 is used to power the micro sd slot, dldo1 is used for wifi. This commit adds a defconfig + dts (as submitted to the kernel) for the gt90h-v4 pcb. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 14:13:03 +00:00
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08 00:27:54 +00:00
CONFIG_SPL=y
sunxi: Add support for gt90h-v4 tablets The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot. The pmic setup on this board is somewhat special, dcdc2 MUST be set to 1.1V instead of the usual 1.2V otherwise the board is very unstable. aldo1 is used to power the micro sd slot, dldo1 is used for wifi. This commit adds a defconfig + dts (as submitted to the kernel) for the gt90h-v4 pcb. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 14:13:03 +00:00
CONFIG_MACH_SUN8I_A23=y
CONFIG_DRAM_CLK=480
CONFIG_DRAM_ZQ=32767
CONFIG_MMC0_CD_PIN="PB4"
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
CONFIG_USB0_ID_DET="PH8"
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:55000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_EN="PH6"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-gt90h-v4"
configs: Migrate CONFIG_NR_DRAM_BANKS We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 12:16:24 +00:00
CONFIG_NR_DRAM_BANKS=1
sunxi: Add support for gt90h-v4 tablets The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot. The pmic setup on this board is somewhat special, dcdc2 MUST be set to 1.1V instead of the usual 1.2V otherwise the board is very unstable. aldo1 is used to power the micro sd slot, dldo1 is used for wifi. This commit adds a defconfig + dts (as submitted to the kernel) for the gt90h-v4 pcb. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 14:13:03 +00:00
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
# CONFIG_CMD_FLASH is not set
disk: convert CONFIG_DOS_PARTITION to Kconfig Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-27 10:00:37 +00:00
# CONFIG_SPL_DOS_PARTITION is not set
disk: convert CONFIG_EFI_PARTITION to Kconfig Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-27 10:00:41 +00:00
# CONFIG_SPL_EFI_PARTITION is not set
sunxi: power: Make all voltages configurable through Kconfig On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-30 13:22:42 +00:00
CONFIG_AXP_DLDO1_VOLT=3300
Convert all of CONFIG_CONS_INDEX to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-07 00:02:27 +00:00
CONFIG_CONS_INDEX=5
Reorder defconfigs with 'savedefconfig' Some boards' defconfigs are disordered. Reorder them. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-09-28 12:14:15 +00:00
CONFIG_USB_MUSB_HOST=y
configs: Migrate all of the existing USB symbols, except fastboot This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-25 21:50:26 +00:00
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
Reference in New Issue Copy Permalink