2005-09-23 09:05:55 +00:00
|
|
|
AMCC Ocotea Board
|
2004-03-14 00:59:59 +00:00
|
|
|
|
|
|
|
|
Last Update: March 2, 2004
|
|
|
|
|
=======================================================================
|
|
|
|
|
|
2005-09-23 09:05:55 +00:00
|
|
|
This file contains some handy info regarding U-Boot and the AMCC
|
2004-03-14 00:59:59 +00:00
|
|
|
Ocotea 440gx evalutation board. See the README.ppc440 for additional
|
|
|
|
|
information.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SWITCH SETTINGS & JUMPERS
|
|
|
|
|
==========================
|
|
|
|
|
|
|
|
|
|
Here's what I've been using successfully. If you feel inclined to
|
|
|
|
|
change things ... please read the docs!
|
|
|
|
|
|
|
|
|
|
DIPSW U46 U80
|
|
|
|
|
------------------------
|
|
|
|
|
SW 1 off off
|
|
|
|
|
SW 2 on off
|
|
|
|
|
SW 3 off off
|
|
|
|
|
SW 4 off off
|
|
|
|
|
SW 5 off off
|
|
|
|
|
SW 6 on on
|
|
|
|
|
SW 7 on off
|
|
|
|
|
SW 8 on off
|
|
|
|
|
|
|
|
|
|
J41: strapped
|
|
|
|
|
J42: open
|
|
|
|
|
|
|
|
|
|
All others are factory default.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
I2C Information
|
|
|
|
|
=====================
|
|
|
|
|
|
|
|
|
|
See README.ebony for information.
|
|
|
|
|
|
|
|
|
|
PCI
|
|
|
|
|
===========================
|
|
|
|
|
|
|
|
|
|
Untested at the time of writing.
|
|
|
|
|
|
|
|
|
|
PPC440GX Ethernet EMACs
|
|
|
|
|
===========================
|
|
|
|
|
|
|
|
|
|
All EMAC ports have been tested and are known to work
|
|
|
|
|
with EPS Group 4.
|
|
|
|
|
|
|
|
|
|
Special note about the Cicada CIS8201:
|
|
|
|
|
The CIS8201 Gigabit PHY comes up in GMII mode by default.
|
|
|
|
|
One must hit an extended register to allow use of RGMII mode.
|
|
|
|
|
This has been done in the 440gx_enet.c file with a #ifdef/endif
|
|
|
|
|
pair.
|
|
|
|
|
|
2005-09-23 09:05:55 +00:00
|
|
|
AMCC does not store the EMAC ethernet addresses within their PIBS bootloader.
|
2004-03-14 00:59:59 +00:00
|
|
|
The addresses contained in the config header file are from my particular
|
|
|
|
|
board and you _*should*_ change them to reflect your board either in the
|
|
|
|
|
config file and/or in your environment variables. I found the addresses on
|
|
|
|
|
labels on the bottom side of the board.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BDI2k or JTAG Debugging
|
|
|
|
|
===========================
|
|
|
|
|
|
|
|
|
|
For ease of debugging you can swap the small boot flash and external SRAM
|
|
|
|
|
by changing U46:3 to on. You can then use the sram as your boot flash by
|
|
|
|
|
loading the sram via the jtag debugger.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Regards,
|
|
|
|
|
--Travis
|
|
|
|
|
<tsawyer@sandburst.com>
|
