leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
2ddf84679d
u-boot/configs/imx6dl_mamoj_defconfig

65 lines
1.5 KiB
Plaintext
Raw Normal View History

i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_SYS_TEXT_BASE=0x17800000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-01 12:19:22 +00:00
CONFIG_SYS_MALLOC_LEN=0x2300000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-10 19:31:07 +00:00
CONFIG_NR_DRAM_BANKS=1
env: Finish migration of common ENV options - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-19 01:02:10 +00:00
CONFIG_ENV_SIZE=0x20000
CONFIG_ENV_OFFSET=0x100000
arm: mx6: Make all i.MX6 SoCs user-selectable We have a number of platforms that are a combination of a carrier board and System-on-Module (SoM) that in turn allows for the board to have different SoCs on it. In some cases, this is handled via board-specific Kconfig options. In other cases we make use of CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid configurations as we will not in turn get options that in Kconfig are selected by or depend on that setting. To resolve this, make the SoC option a choice in Kconfig and make boards depend on what they can support. This change opens us up for further clean-ups in the cases where a single CONFIG_TARGET_xxx can support different SoCs and today they do not, or do not cleanly do so. Reported-by: Matt Porter <mporter@konsulko.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Soeren Moch <smoch@web.de> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Heiko Schocher <hs@denx.de> Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Lukasz Majewski <lukma@denx.de> Cc: Akshay Bhat <akshaybhat@timesys.com> Cc: Ken Lin <Ken.Lin@advantech.com.tw> Cc: Ian Ray <ian.ray@ge.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Cc: Simone CIANNI <simone.cianni@bticino.it> Cc: Adam Ford <aford173@gmail.com> Cc: Marcin Niestroj <m.niestroj@grinn-global.com> Cc: "Eric Bénard" <eric@eukrea.com> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Jason Liu <jason.hui.liu@nxp.com> Cc: Ye Li <ye.li@nxp.com> Cc: Eric Nelson <eric@nelint.com> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Parthiban Nallathambi <parthiban@linumiz.com> Cc: Marek Vasut <marex@denx.de> Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Niel Fourie <lusus@denx.de> Cc: Martyn Welch <martyn.welch@collabora.com> Cc: Richard Hu <richard.hu@technexion.com> Cc: Stefan Roese <sr@denx.de> Cc: Boris Brezillon <bbrezillon@kernel.org> Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com> Cc: Breno Lima <breno.lima@nxp.com> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org> Cc: Silvio Fricke <open-source@softing.de> Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2020-08-18 11:43:50 +00:00
CONFIG_MX6QDL=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 20:15:47 +00:00
CONFIG_TARGET_MX6DL_MAMOJ=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28 14:17:29 +00:00
CONFIG_DEFAULT_DEVICE_TREE="imx6dl-mamoj"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-06 17:54:25 +00:00
CONFIG_SPL_TEXT_BASE=0x00908000
Convert CONFIG_SPL_DRIVERS_MISC et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_DRIVERS_MISC CONFIG_SPL_ENV_SUPPORT CONFIG_SPL_GPIO CONFIG_SPL_I2C CONFIG_SPL_LDSCRIPT CONFIG_SPL_LIBCOMMON_SUPPORT CONFIG_SPL_LIBGENERIC_SUPPORT CONFIG_SPL_LOAD_FIT_ADDRESS CONFIG_SPL_MMC CONFIG_SPL_NAND_SUPPORT CONFIG_SPL_NO_CPU_SUPPORT CONFIG_SPL_OS_BOOT CONFIG_SPL_POWER CONFIG_SPL_STACK_R CONFIG_SPL_STACK_R_ADDR CONFIG_SPL_WATCHDOG CONFIG_SPL_TEXT_BASE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-31 03:03:56 +00:00
CONFIG_SPL_DRIVERS_MISC=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07 19:25:00 +00:00
CONFIG_IMX_HAB=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
# CONFIG_CMD_BMODE is not set
configs: imx6dl_mamoj_defconfig: Enable LTO on imx6dl_mamoj board Enable LTO on mamoj to reduce SPL and uboot size. Tested with gcc gcc-11.1.0 U-Boot 2022.04-rc4-00051-g17fc5facd0 (Mar 23 2022 - 16:43:43 +0100) CPU: Freescale i.MX6DL rev1.3 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 40C Reset cause: POR Model: BTicino i.MX6DL Mamoj board DRAM: 512 MiB Core: 29 devices, 12 uclasses, devicetree: separate MMC: FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Net: Error: ethernet@2188000 address not set. No ethernet found. Tested-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-03-23 16:52:17 +00:00
CONFIG_LTO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 14:33:18 +00:00
CONFIG_SYS_MEMTEST_START=0x80000000
CONFIG_SYS_MEMTEST_END=0x88000000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 15:57:37 +00:00
CONFIG_DISTRO_DEFAULTS=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_BOOTDELAY=3
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 15:57:37 +00:00
CONFIG_SPL_OS_BOOT=y
spl: Convert SYS_MMCSD_RAW_MODE_KERNEL_SECTOR to Kconfig Falcon mode is very useful in improving boot speed. A question that Falcon mode asks is "Where do I look for the kernel". With MMC boot media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. The scope of this patch is to move this to Kconfig. It is possible for a system to support Falcon mode from NOR but not MMC. In that case, mmc_load_image_raw_os() would not be used. To address this, conditionally compile mmc_load_image_raw_os() when SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> [trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-30 16:39:59 +00:00
CONFIG_SPL_FALCON_BOOT_MMCSD=y
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x1000
Convert CONFIG_CMD_ASKENV et al to Kconfig This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-26 19:06:18 +00:00
CONFIG_CMD_SPL=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_CRC32_VERIFY=y
CONFIG_CMD_MEMTEST=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 15:57:37 +00:00
CONFIG_CMD_DFU=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_CMD_GPIO=y
i.MX6DL: mamoj: Add I2C support i.MX6DL Mamoj has i2c3 and i2c4 buses, add support through DM_I2C with dt definition. i2c log: Reviewed-by: Stefano Babic <sbabic@denx.de> ======= => i2c bus Bus 2: i2c@021a8000 Bus 3: i2c@021f8000 => i2c dev 2 Setting bus to 2 => i2c speed 400000 Setting bus speed to 400000 Hz => i2c probe Valid chip addresses: 20 51 53 => i2c md 53 0xff 00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ => i2c md 51 0xff 00ff: a8 08 40 50 09 43 46 52 42 18 80 8e ae a9 d0 53 ..@P.CFRB......S => i2c dev 3 Setting bus to 3 => i2c speed 100000 Setting bus speed to 100000 Hz => i2c probe Valid chip addresses: 08 40 48 4B => i2c md 08 0xff 00ff: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
2018-05-07 05:51:35 +00:00
CONFIG_CMD_I2C=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
configs: imx6dl_mamoj: Enable fastboot and ums Enable fastboot and ums for host to interact eMMC on Mamoj board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
2018-05-07 05:51:37 +00:00
CONFIG_CMD_USB_MASS_STORAGE=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 15:57:37 +00:00
CONFIG_CMD_CACHE=y
CONFIG_CMD_PMIC=y
CONFIG_CMD_EXT4_WRITE=y
Convert CONFIG_ENV_OVERWRITE to Kconfig This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-03 11:48:56 +00:00
CONFIG_ENV_OVERWRITE=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_ENV_IS_IN_MMC=y
env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-13 03:46:36 +00:00
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-24 21:14:47 +00:00
CONFIG_SYS_MMC_ENV_DEV=2
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09 16:22:06 +00:00
CONFIG_BOUNCE_BUFFER=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 15:57:37 +00:00
CONFIG_DFU_MMC=y
CONFIG_USB_FUNCTION_FASTBOOT=y
CONFIG_FASTBOOT_BUF_ADDR=0x12000000
CONFIG_FASTBOOT_BUF_SIZE=0x10000000
CONFIG_FASTBOOT_FLASH=y
CONFIG_FASTBOOT_FLASH_MMC_DEV=2
CONFIG_SYS_I2C_MXC=y
Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-01 07:58:27 +00:00
CONFIG_SUPPORT_EMMC_BOOT=y
Convert CONFIG_FSL_USDHC to Kconfig This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-14 12:23:43 +00:00
CONFIG_FSL_USDHC=y
mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD Like in Linux, just use CONFIG_MTD to compile the MTD stack. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-10-03 17:50:05 +00:00
CONFIG_MTD=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-03-06 12:48:27 +00:00
CONFIG_PHY_MICREL_KSZ8XXX=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_FEC_MXC=y
Convert CONFIG_MII et al to Kconfig This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-21 04:03:57 +00:00
CONFIG_MII=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 15:57:37 +00:00
CONFIG_IMX_THERMAL=y
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_USB=y
usb: Enforce DM_USB migration for USB_HOST devices. As the deadline for migration to DM_USB, when using a USB host controller has now gone two years past the deadline, enforce migration. This is done by: - Ensuring that all host controller options (other than the very legacy old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and OF_CONTROL. - Remove other parts of Kconfig logic that had platforms pick DM_USB. - To keep Kconfig happy, have some select statements test for USB_HOST as well. - Re-order some Kconfig entries and menus so that we can cleanly pick host or gadget roles. For the various HCD options that have platform glue options, group them together and update dependencies in some cases. - As SPL_DM_USB is not required, on platforms that had not yet enabled it, disable it. Cc: Marek Vasut <marex@denx.de> Cc: Icenowy Zheng <icenowy@aosc.io> Cc: Samuel Holland <samuel@sholland.org> Cc: FUKAUMI Naoki <naobsd@gmail.com> Cc: Andre Przywara <andre.przywara@arm.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-09 14:11:56 +00:00
# CONFIG_SPL_DM_USB is not set
i.MX6: board: Add BTicino i.MX6DL Mamoj initial support Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-07 05:51:34 +00:00
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="FSL"
CONFIG_USB_GADGET_VENDOR_NUM=0x0525
CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
CONFIG_CI_UDC=y
Reference in New Issue Copy Permalink