44 lines
2.4 KiB
Plaintext
44 lines
2.4 KiB
Plaintext
|
This file contains API information of the initialization code written for
|
||
|
|
Vitesse cross-point devices, VSC3316 and VSC3308 for board B4860QDS
|
||
|
|
|
||
|
|
Author: Shaveta Leekha <shaveta@freescale.com>
|
||
|
|
|
||
|
|
About Device:
|
||
|
|
=============
|
||
|
|
VSC 3316/3308 is a low-power, low-cost asynchronous crosspoint switch capable of data rates upto 11.5Gbps.
|
||
|
|
|
||
|
|
VSC3316 has 16 input and 16 output ports whereas VSC3308 has 8 input and 8 output ports. Programming of these devices are performed by two-wire or four-wire serial interface.
|
||
|
|
|
||
|
|
Initialization:
|
||
|
|
===============
|
||
|
|
On reset, VSC devices are in low-power state with all inputs, outputs and connections in an off state.
|
||
|
|
First thing required is to program it to interface with either two-wire or four-wire interface.
|
||
|
|
In our case the interface is two-wire I2C serial interface. So the value in Interface mode register at address 79.h to be written is 0x02 for two-wire interface. Also for crosspoint connections to be activated, 01.h value need to be written in 75.h (core configuration register).
|
||
|
|
|
||
|
|
API Overview:
|
||
|
|
=============
|
||
|
|
|
||
|
|
vsc_if_enable(u8 vsc_addr):
|
||
|
|
--------------------------
|
||
|
|
This API programs VSC to interface with either two-wire or four-wire interface. In our case the interface is two-wire I2C serial interface. So the value in Interface mode register at address 79.h to be written is 0x02 for two-wire interface.
|
||
|
|
Parameters:
|
||
|
|
vsc_addr - Address of the VSC device on board.
|
||
|
|
|
||
|
|
|
||
|
|
vsc3316_config(u8 vsc_addr, int con_arr[][2], u8 num_con):
|
||
|
|
---------------------------------------------------------
|
||
|
|
This API configures the VSC3316 device for required connections. Connection through the VSC device requires the inputs and outputs to be properly configured.
|
||
|
|
Connection registers are on page 00. It Configures the selected input and output correctly and join them to make a connection. It also program Input state register, Global input ISE, Global input LOS, Global core control, Output mode register and core control registers etc.
|
||
|
|
vsc3308_config(u8 vsc_addr, int con_arr[][2], u8 num_con) does the essential configurations for VSC3308.
|
||
|
|
|
||
|
|
Parameters:
|
||
|
|
vsc_addr - Address of the VSC device on board.
|
||
|
|
con_arr - connection array
|
||
|
|
num_con - number of connections to be configured
|
||
|
|
|
||
|
|
vsc_wp_config(u8 vsc_addr):
|
||
|
|
--------------------------
|
||
|
|
For crosspoint connections to be activated, 01.h value need to be written in 75.h (core configuration register), which is done by this API.
|
||
|
|
Parameters:
|
||
|
|
vsc_addr - Address of the VSC device on board.
|