leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
master
u-boot/configs/Mele_A1000G_quad_defconfig

22 lines
526 B
Plaintext
Raw Permalink Normal View History

sunxi: Add new Mele_A1000G_quad defconfig The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using the same defconfig (and dts on the kernel side) for both models. Unfortunately this does not work for the otg controller, on the M9 this is routed to a micro-usb connector on the outside, while as on the A1000G-quad it is connected to an usb to sata bridge. This commit adds a new defconfig for the Mele-A1000G-quad to allow using different otg controller settings on the 2 boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-06-01 14:37:24 +00:00
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28 14:17:29 +00:00
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-mele-a1000g-quad"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08 00:27:54 +00:00
CONFIG_SPL=y
sunxi: Add new Mele_A1000G_quad defconfig The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using the same defconfig (and dts on the kernel side) for both models. Unfortunately this does not work for the otg controller, on the M9 this is routed to a micro-usb connector on the outside, while as on the A1000G-quad it is connected to an usb to sata bridge. This commit adds a new defconfig for the Mele-A1000G-quad to allow using different otg controller settings on the 2 boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-06-01 14:37:24 +00:00
CONFIG_MACH_SUN6I=y
CONFIG_DRAM_ZQ=120
CONFIG_USB1_VBUS_PIN="PC27"
CONFIG_USB2_VBUS_PIN=""
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 12:46:52 +00:00
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
Convert CONFIG_PHYLIB et al to Kconfig This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-24 19:35:53 +00:00
CONFIG_PHY_REALTEK=y
sunxi: Add new Mele_A1000G_quad defconfig The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using the same defconfig (and dts on the kernel side) for both models. Unfortunately this does not work for the otg controller, on the M9 this is routed to a micro-usb connector on the outside, while as on the A1000G-quad it is connected to an usb to sata bridge. This commit adds a new defconfig for the Mele-A1000G-quad to allow using different otg controller settings on the 2 boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-06-01 14:37:24 +00:00
CONFIG_ETH_DESIGNWARE=y
Convert CONFIG_MII et al to Kconfig This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-21 04:03:57 +00:00
CONFIG_MII=y
sunxi: Move SUNXI_GMAC to Kconfig Move the SUNXI_GMAC config option to Kconfig, remove it from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC. Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-02 10:59:03 +00:00
CONFIG_SUN7I_GMAC=y
configs: Resync with savedefconfig Resync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-25 21:19:18 +00:00
CONFIG_INITIAL_USB_SCAN_DELAY=2000
sunxi: power: Make all voltages configurable through Kconfig On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-30 13:22:42 +00:00
CONFIG_AXP_DCDC1_VOLT=3300
common: add CMD_GPIO to Kconfig Add CMD_GPIO to Kconfig and run tools/moveconfig.py . Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-11 13:39:33 +00:00
CONFIG_AXP_ALDO1_VOLT=3300
sunxi: power: Make all voltages configurable through Kconfig On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-30 13:22:42 +00:00
CONFIG_AXP_DLDO1_VOLT=3300
CONFIG_AXP_DLDO4_VOLT=3300
sunxi: Update selects in arch/arm/Kconfig for DM conversions With certain features being convert to DM now we want sunxi to default to having DM enabled for ETH/SERIAL and USB in some cases. Cc: Hans de Goede <hdegoede@redhat.com> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Tom Rini <trini@konsulko.com> [hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-06-30 20:51:15 +00:00
CONFIG_USB_EHCI_HCD=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-02-07 19:53:03 +00:00
CONFIG_USB_OHCI_HCD=y
sunxi: usb: USB_MUSB_SUNXI move to musb-new Kconfig Now that the musb-new driver has a Kconfig, we can move Kconfig options to enable controllers to it, so that it's easier in e.g. menuconfig. In addition, this allows declaring support for USB_MUSB_HOST/GADGET in defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected automatically when needed. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-08-04 15:04:08 +00:00
CONFIG_USB_MUSB_HOST=y
Reference in New Issue Copy Permalink