forked from Minki/linux
a4240d3af6
DRA72-EVM now has an upgrade to Rev C with SR2.0 silicon. As part of this change, a few updates were factored in that were software incompatible with previous board in few areas: - We now use DP83867 ethernet phy instead of older DP838865 which fails in certain use cases. - Two Ethernet ports now instead of the single one in rev B. - polarities changed for certain pcf gpios - Due to SoC phy current requirements, VDDA supplies are split between ldo3 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is still supplied by ldo5, HDMI is now supplied by LDO2 instead of using LDO3. NOTE: It does not make much sense to spin off a new board compatible flag since there is no real benefit for the same. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
74 lines
1.6 KiB
Plaintext
74 lines
1.6 KiB
Plaintext
/*
|
|
* Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
#include "dra72-evm-common.dtsi"
|
|
#include <dt-bindings/net/ti-dp83867.h>
|
|
|
|
/ {
|
|
model = "TI DRA722 Rev C EVM";
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */
|
|
};
|
|
};
|
|
|
|
&tps65917_regulators {
|
|
ldo2_reg: ldo2 {
|
|
/* LDO2_OUT --> VDDA_1V8_PHY2 */
|
|
regulator-name = "ldo2";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
};
|
|
|
|
&hdmi {
|
|
vdda-supply = <&ldo2_reg>;
|
|
};
|
|
|
|
&pcf_gpio_21 {
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
|
|
};
|
|
|
|
&mac {
|
|
mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
|
|
<&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */
|
|
<&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */
|
|
dual_emac;
|
|
};
|
|
|
|
&cpsw_emac0 {
|
|
phy_id = <&davinci_mdio>, <2>;
|
|
phy-mode = "rgmii-id";
|
|
dual_emac_res_vlan = <1>;
|
|
};
|
|
|
|
&cpsw_emac1 {
|
|
phy_id = <&davinci_mdio>, <3>;
|
|
phy-mode = "rgmii-id";
|
|
dual_emac_res_vlan = <2>;
|
|
};
|
|
|
|
&davinci_mdio {
|
|
dp83867_0: ethernet-phy@2 {
|
|
reg = <2>;
|
|
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
|
|
ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_NS>;
|
|
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
|
|
};
|
|
|
|
dp83867_1: ethernet-phy@3 {
|
|
reg = <3>;
|
|
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
|
|
ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_NS>;
|
|
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
|
|
};
|
|
};
|